Comparison of plasma-sprayed alumina coatings by RF and DC plasma spraying

1995 ◽  
Vol 4 (1) ◽  
pp. 59-66 ◽  
Author(s):  
L. Blanchi ◽  
A. Grimaud ◽  
F. Blein ◽  
P. Lucchèse ◽  
P. Fauchais
Keyword(s):  
Plasma Spraying ◽  
Dc Plasma ◽  
Alumina Coatings ◽  
Plasma Sprayed

Electron microscopy studies of plasma-sprayed materials

1983 ◽  
Vol 41 ◽  
pp. 70-71
Author(s):  
K.R. Subramanian ◽  
A.H. King ◽  
H. Herman
Keyword(s):  
Plasma Spraying ◽  
Substrate Surface ◽  
Flame Temperature ◽  
Ceramic Coatings ◽  
Metallic Substrates ◽  
Hot Plasma ◽  
Almost All ◽  
Plasma Sprayed ◽  
Hostile Environments ◽  
Plasma Spraying Process

Plasma spraying is a technique which is used to apply coatings to metallic substrates for a variety of purposes, including hardfacing, corrosion resistance and thermal barrier applications. Almost all of the applications of this somewhat esoteric fabrication technique involve materials in hostile environments and the integrity of the coatings is of paramount importance: the effects of process variables on such properties as adhesive strength, cohesive strength and hardness of the substrate/coating system, however, are poorly understood.Briefly, the plasma spraying process involves forming a hot plasma jet with a maximum flame temperature of approximately 20,000K and a gas velocity of about 40m/s. Into this jet the coating material is injected, in powder form, so it is heated and projected at the substrate surface. Relatively thick metallic or ceramic coatings may be speedily built up using this technique.

scholarly journals Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 879
Author(s):  
Monika Michalak ◽  
Paweł Sokołowski ◽  
Mirosław Szala ◽  
Mariusz Walczak ◽  
Leszek Łatka ◽  
...  
Keyword(s):  
Plasma Spraying ◽  
Wear Behavior ◽  
Ceramic Coatings ◽  
Suspension Plasma Spraying ◽  
Atmospheric Plasma ◽  
Hvof Spraying ◽  
The Coefficient Of Friction ◽  
Wear Mode ◽  
Α Al2o3 ◽  
Plasma Sprayed

Thermally sprayed ceramic coatings are applied for the protection of surfaces that are exposed mainly to wear, high temperatures, and corrosion. In recent years, great interest has been garnered by spray processes with submicrometric and nanometric feedstock materials, due to the refinement of the structure and improved coating properties. This paper compares the microstructure and tribological properties of alumina coatings sprayed using conventional atmospheric plasma spraying (APS), and various methods that use finely grained suspension feedstocks, namely, suspension plasma spraying (SPS) and suspension high-velocity oxy-fuel spraying (S-HVOF). Furthermore, the suspension plasma-sprayed Al2O3 coatings have been deposited with radial (SPS) and axial (A-SPS) feedstock injection. The results showed that all suspension-based coatings demonstrated much better wear resistance than the powder-sprayed ones. S-HVOF and axial suspension plasma spraying (A-SPS) allowed for the deposition of the most dense and homogeneous coatings. Dense-structured coatings with low porosity (4 vol.%) and good cohesion to the metallic substrate, containing a high content of α–Al2O3 phase (56 vol.%) and a very low wear rate (0.2 ± 0.04 mm3 × 10−6/(N∙m)), were produced with the S-HVOF method. The wear mechanism of ceramic coatings included the adhesive wear mode supported by the fatigue-induced material delamination. Moreover, the presence of wear debris and tribofilm was confirmed. Finally, the coefficient of friction for the coatings was in the range between 0.44 and 0.68, with the highest values being recorded for APS sprayed coatings.

Laser Sintering of Nano-Al2O3 Powders on Plasma Sprayed Ceramic Based Coatings

2007 ◽  
Author(s):  
Lida Shen ◽  
Yinhui Huang ◽  
Zongjun Tian ◽  
Guoran Hua
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Plasma Spraying ◽  
Bond Coat ◽  
Continuous Wave ◽  
Ceramic Coatings ◽  
Laser Sintering ◽  
Al2o3 Ceramic ◽  
Plasma Sprayed ◽  
Steel Substrates

This paper describes an investigation of nano-Al2O3 powders reinforced ceramic coatings, which has included NiCrAl and Al2O3+13%wt.TiO2 coats pre-produced by atmosphere plasma spraying, implemented by laser sintering. Commercial NiCrAl powders were plasma sprayed onto 45 Steel substrates to give a bond coat with thickness of ∼100μm. The 600μm thick Al2O3+13%wt.TiO2 based coating was also plasma sprayed on top of the NiCrAl bond coat. With 2.5kw continuous wave CO2 laser, nano-Al2O3 ceramic powders were laser sintered on the based Coatings. The micro structure and chemical composition of the modified Al2O3+13%wt.TiO2 coatings were analyzed by such detection devices as scanning electronic microscope (SEM) and x-ray diffraction (XRD). Microhardness, wear resistance and corrosion resistance of the modified coatings were also tested and compared with that of the unmodified. The results show that the crystal grain size of Al2O3 had no obvious growth. In addition, due to the nanostructured Al2O3 ceramic phases, the coatings exhibited higher microhardness, better wear resistance and corrosion resistance than those unmodified counterparts. The complex process of plasma spraying with laser sintering as a potential effective way of the application of ceramic nano materials was also simply discussed and summarized in the end.

Use of Different Process Gases for Manufacturing Isolating Alumina Coatings by Flame Spraying with Cords

2021 ◽  
Author(s):  
M. Hauer ◽  
M. Meyer ◽  
D. Billieres ◽  
C. Bricquet ◽  
F. Gerstgrasser ◽  
...  
Keyword(s):  
Volume Resistivity ◽  
Alpha Phase ◽  
Flame Spraying ◽  
Flame Spray ◽  
Alumina Coatings ◽  
Spray Coatings ◽  
Aluminum Hydroxides ◽  
Fine Microstructure ◽  
Plasma Sprayed ◽  
Aluminum Substrates

Abstract This study assesses the quality of flame-sprayed alumina coatings produced from recently developed alumina cord using argon and compressed air as atomizing gases. Coatings of different thicknesses were deposited on aluminum substrates and then analyzed using optical microscopy, X-ray diffraction, and resistivity measurements. The coatings, particularly those sprayed with argon, had fine microstructure and higher surface and volume resistivity than flame-spray coatings made from alumina cord in the past. They were also found to have higher alpha phase content than plasma-sprayed coatings, regardless of the atomizing gas used. The effect of humidity and the possible formation of aluminum hydroxides are also addressed.

Plasma Sprayed Ultra High Temperature Ceramics for Thermal Protection Systems

2000 ◽  
Author(s):  
T. Valente ◽  
C. Bartuli ◽  
G. Visconti ◽  
M. Tului
Keyword(s):  
Plasma Spraying ◽  
High Performance ◽  
Thermal Protection ◽  
Electrical Discharge Machining ◽  
High Heat ◽  
Heat Fluxes ◽  
Space Vehicles ◽  
Ultra High Temperature Ceramics ◽  
Protection Systems ◽  
Plasma Sprayed

Abstract Reusable space vehicles, which must withstand re-entry into the Earth's atmosphere, require external protection systems (TPS) which are usually in the forms of rigid surface in areas of high or moderate working temperature. High heat fluxes and temperatures related to high performance hypervelocity flights also require the use of TPS materials having good oxidation and thermal shock resistance, dimensional stability, and ablation resistance. Components by these materials are usually fabricated, starting from either billets or plate stocks, by uniaxial hot pressing, and complex parts, such as low radius edges, are then obtained by electrical discharge machining technique. This article investigates an alternative fabrication technology, based on plasma spraying, to produce near net shape components. Results of experimental activities, such as optimization of plasma spraying parameters based on a DOE approach, are reported and discussed.

Plasma Spraying of Self-Lubricating Cr2O3-CaF2 Coatings

1997 ◽  
Author(s):  
F. Vos ◽  
L. Delaey ◽  
M. De Bonte ◽  
L. Froyen
Keyword(s):  
Plasma Spraying ◽  
Matrix Material ◽  
Production Method ◽  
Atmospheric Plasma ◽  
Spray Parameters ◽  
The Matrix ◽  
Preparation Step ◽  
Plasma Sprayed ◽  
The Relationship ◽  
Selection Of

Abstract Results are presented of a project analysing the relationship between the production parameters of plasma sprayed self-lubricating Cr2O3-CaF2 coatings and their structural, wear and lubricating properties. The production method consists of a preparation step where a powder blend of the matrix material (Cr203) and solid lubricant (CaF2) is agglomerated, followed by atmospheric plasma spraying (APS) of the agglomerates. Selection of the most appropriate agglomeration and plasma spray parameters as well as the microstructure of the coatings will be discussed.

Ultrasonic technique for measuring porosity of plasma-sprayed alumina coatings

1997 ◽  
Vol 6 (4) ◽  
pp. 486-488 ◽  
Author(s):  
S. Parthasarathi ◽  
B. R. Tittmann ◽  
E. J. Onesto
Keyword(s):  
Ultrasonic Technique ◽  
Alumina Coatings ◽  
Plasma Sprayed

Composite ZrO2-Based Cermet Material Modified with Mo

2015 ◽  
Vol 237 ◽  
pp. 3-8 ◽  
Author(s):  
Adriana Wrona ◽  
Kinga Czechowska ◽  
Małgorzata Osadnik ◽  
Małgorzata Kamińska ◽  
Marcin Lis ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Phase Composition ◽  
Plasma Spraying ◽  
Alloy Coating ◽  
Metallic Material ◽  
Cermet Material ◽  
Powder Composites ◽  
Annealing Procedure ◽  
Plasma Sprayed ◽  
Structure And Microstructure

The work presents studies of a new ceramic-metallic material. The base is a ZrO2-Mo cermet which is modified with metallic Mo or Mo85Re15 alloy coating. The structure and microstructure of Mo85Re15 alloy powders and the composite were characterized. The annealing procedure was found to influence phase composition of powder composites but not their morphology. The plasma sprayed powders, both metallic and alloyed, form coatings that adhere well to the cermet substrate. The coatings show a better homogeneity in comparison to powders and more favourable phase composition.Keywords: cermets, plasma spraying, corrosion resistance

Sign in / Sign up

Export Citation Format

Share Document