scholarly journals Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 879
Author(s):  
Monika Michalak ◽  
Paweł Sokołowski ◽  
Mirosław Szala ◽  
Mariusz Walczak ◽  
Leszek Łatka ◽  
...  
Keyword(s):  
Plasma Spraying ◽  
Wear Behavior ◽  
Ceramic Coatings ◽  
Suspension Plasma Spraying ◽  
Atmospheric Plasma ◽  
Hvof Spraying ◽  
The Coefficient Of Friction ◽  
Wear Mode ◽  
Α Al2o3 ◽  
Plasma Sprayed

Thermally sprayed ceramic coatings are applied for the protection of surfaces that are exposed mainly to wear, high temperatures, and corrosion. In recent years, great interest has been garnered by spray processes with submicrometric and nanometric feedstock materials, due to the refinement of the structure and improved coating properties. This paper compares the microstructure and tribological properties of alumina coatings sprayed using conventional atmospheric plasma spraying (APS), and various methods that use finely grained suspension feedstocks, namely, suspension plasma spraying (SPS) and suspension high-velocity oxy-fuel spraying (S-HVOF). Furthermore, the suspension plasma-sprayed Al2O3 coatings have been deposited with radial (SPS) and axial (A-SPS) feedstock injection. The results showed that all suspension-based coatings demonstrated much better wear resistance than the powder-sprayed ones. S-HVOF and axial suspension plasma spraying (A-SPS) allowed for the deposition of the most dense and homogeneous coatings. Dense-structured coatings with low porosity (4 vol.%) and good cohesion to the metallic substrate, containing a high content of α–Al2O3 phase (56 vol.%) and a very low wear rate (0.2 ± 0.04 mm3 × 10−6/(N∙m)), were produced with the S-HVOF method. The wear mechanism of ceramic coatings included the adhesive wear mode supported by the fatigue-induced material delamination. Moreover, the presence of wear debris and tribofilm was confirmed. Finally, the coefficient of friction for the coatings was in the range between 0.44 and 0.68, with the highest values being recorded for APS sprayed coatings.

scholarly journals Microstructure and Wear Behaviors of Plasma-Sprayed MoAlB Ceramic Coating

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 474
Author(s):  
Fuzhu Li ◽  
Shengnan Sun ◽  
Yong Xu ◽  
Lihui Tian ◽  
Yun Wang ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Plasma Spraying ◽  
Ceramic Coating ◽  
Adhesive Wear ◽  
Ceramic Coatings ◽  
Atmospheric Plasma ◽  
Wear Rates ◽  
Arc Power ◽  
Plasma Sprayed

MoAlB ceramic coatings were prepared on a 316 steel surface by atmospheric plasma spraying with different arc power levels. The phase composition, microstructure and wear resistance of coatings against GCr15 and Si3N4 counterparts were studied. The MoAlB ceramic decomposed and was oxidized to form MoB and Al2O3 during plasma spraying. With the increase of the arc power, MoAlB experienced more decomposition, but the coatings became denser. When the arc power increased from 30 to 36 kW, the wear rates of coatings against GCr15 and Si3N4 balls reduced by 91% and 78%, respectively. The characterization of wear tracks shows that when against GCr15 counterparts, the main wear mechanisms are abrasive and adhesive wear, and when against Si3N4 counterparts, fatigue and abrasive wear are dominant. The refinement of wear resistance by increasing arc power can be attributed to the improvement of density and adhesive strength among splats.

Electron microscopy studies of plasma-sprayed materials

1983 ◽  
Vol 41 ◽  
pp. 70-71
Author(s):  
K.R. Subramanian ◽  
A.H. King ◽  
H. Herman
Keyword(s):  
Plasma Spraying ◽  
Substrate Surface ◽  
Flame Temperature ◽  
Ceramic Coatings ◽  
Metallic Substrates ◽  
Hot Plasma ◽  
Almost All ◽  
Plasma Sprayed ◽  
Hostile Environments ◽  
Plasma Spraying Process

Plasma spraying is a technique which is used to apply coatings to metallic substrates for a variety of purposes, including hardfacing, corrosion resistance and thermal barrier applications. Almost all of the applications of this somewhat esoteric fabrication technique involve materials in hostile environments and the integrity of the coatings is of paramount importance: the effects of process variables on such properties as adhesive strength, cohesive strength and hardness of the substrate/coating system, however, are poorly understood.Briefly, the plasma spraying process involves forming a hot plasma jet with a maximum flame temperature of approximately 20,000K and a gas velocity of about 40m/s. Into this jet the coating material is injected, in powder form, so it is heated and projected at the substrate surface. Relatively thick metallic or ceramic coatings may be speedily built up using this technique.

scholarly journals Microstructure and Wear Behavior of Plasma-Sprayed TiO2–SiAlON Ceramic Coating

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1268
Author(s):  
Yun Wang ◽  
Weichao Wan ◽  
Junhong Mao ◽  
Lihui Tian ◽  
Ruitao Li
Keyword(s):  
Ceramic Coating ◽  
Wear Behavior ◽  
Rutile Phase ◽  
Atmospheric Plasma ◽  
Tio2 Anatase ◽  
Sialon Ceramic ◽  
Mating Surface ◽  
Starved Lubrication ◽  
Plasma Sprayed ◽  
Lubrication Conditions

In this study, atmospheric plasma spray was employed to deposit TiO2–SiAlON ceramic coating on 316 stainless steel. The phases and microstructure of the ceramic coating were investigated. Additionally, comparative studies on the tribological performances of the substrate and the ceramic coating, under both dry and starved lubrication conditions, were carried out. The SiAlON phase was preserved, while partial TiO2 anatase was transformed to rutile phase. The wear rate of the coating was roughly 1/3 of that of the substrate under both conditions. The wear mechanisms of the ceramic coating were surface fracture and abrasive wear in both cases, and the coating under starved lubrication underwent less abrasion. The pores in the coating served as micro-reservoirs, forming an oil layer on the mating surface, and improving tribological properties during sliding.

Laser Sintering of Nano-Al2O3 Powders on Plasma Sprayed Ceramic Based Coatings

2007 ◽  
Author(s):  
Lida Shen ◽  
Yinhui Huang ◽  
Zongjun Tian ◽  
Guoran Hua
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Plasma Spraying ◽  
Bond Coat ◽  
Continuous Wave ◽  
Ceramic Coatings ◽  
Laser Sintering ◽  
Al2o3 Ceramic ◽  
Plasma Sprayed ◽  
Steel Substrates

This paper describes an investigation of nano-Al2O3 powders reinforced ceramic coatings, which has included NiCrAl and Al2O3+13%wt.TiO2 coats pre-produced by atmosphere plasma spraying, implemented by laser sintering. Commercial NiCrAl powders were plasma sprayed onto 45 Steel substrates to give a bond coat with thickness of ∼100μm. The 600μm thick Al2O3+13%wt.TiO2 based coating was also plasma sprayed on top of the NiCrAl bond coat. With 2.5kw continuous wave CO2 laser, nano-Al2O3 ceramic powders were laser sintered on the based Coatings. The micro structure and chemical composition of the modified Al2O3+13%wt.TiO2 coatings were analyzed by such detection devices as scanning electronic microscope (SEM) and x-ray diffraction (XRD). Microhardness, wear resistance and corrosion resistance of the modified coatings were also tested and compared with that of the unmodified. The results show that the crystal grain size of Al2O3 had no obvious growth. In addition, due to the nanostructured Al2O3 ceramic phases, the coatings exhibited higher microhardness, better wear resistance and corrosion resistance than those unmodified counterparts. The complex process of plasma spraying with laser sintering as a potential effective way of the application of ceramic nano materials was also simply discussed and summarized in the end.

Plasma Spraying of Self-Lubricating Cr2O3-CaF2 Coatings

1997 ◽  
Author(s):  
F. Vos ◽  
L. Delaey ◽  
M. De Bonte ◽  
L. Froyen
Keyword(s):  
Plasma Spraying ◽  
Matrix Material ◽  
Production Method ◽  
Atmospheric Plasma ◽  
Spray Parameters ◽  
The Matrix ◽  
Preparation Step ◽  
Plasma Sprayed ◽  
The Relationship ◽  
Selection Of

Abstract Results are presented of a project analysing the relationship between the production parameters of plasma sprayed self-lubricating Cr2O3-CaF2 coatings and their structural, wear and lubricating properties. The production method consists of a preparation step where a powder blend of the matrix material (Cr203) and solid lubricant (CaF2) is agglomerated, followed by atmospheric plasma spraying (APS) of the agglomerates. Selection of the most appropriate agglomeration and plasma spray parameters as well as the microstructure of the coatings will be discussed.

Development & Characterization of Alumina Coating by Atmospheric Plasma Spraying

2018 ◽  
Vol 877 ◽  
pp. 104-109 ◽  
Author(s):  
Jobin Sebastian ◽  
Abyson Scaria ◽  
Don George Kurian
Keyword(s):  
Plasma Spraying ◽  
Elevated Temperatures ◽  
Steel Substrate ◽  
Oxide Coating ◽  
Ceramic Coatings ◽  
Substrate Material ◽  
Atmospheric Plasma ◽  
Flame Spraying ◽  
Alumina Coating ◽  
Spray Process

Ceramic coatings are applied on metals to prevent them from oxidation and corrosion at room as well as elevated temperatures. The service environment, mechanisms of protection, chemical and mechanical compatibility, application method, control of coating quality and ability of the coating to be repaired are the factors that need to be considered while selecting the required coating. The coatings based on oxide materials provides high degree of thermal insulation and protection against oxidation at high temperatures for the underlying substrate materials. These coatings are usually applied by the flame or plasma spraying methods. The surface cleanliness needs to be ensured before spraying. Abrasive blasting can be used to provide the required surface roughness for good adhesion between the substrate and the coating. A pre bond coat like Nickel Chromium can be applied on to the substrate material before spraying the oxide coating to avoid chances of poor adhesion between the oxide coating and the metallic substrate. Plasma spraying produces oxide coatings of greater density, higher hardness, and smooth surface finish than that of the flame spraying process Inert gas is often used for generation of plasma gas so as to avoid the oxidation of the substrate material. The work focuses to develop, characterize and optimize the parameters used in Al2O3 coating on transition stainless steel substrate material for minimizing the wear rate and maximizing the leak tightness using plasma spray process. The experiment is designed using Taguchi’s L9 orthogonal array. The parameters that are to be optimized are plasma voltage, spraying distance and the cooling jet pressure. The characterization techniques includes micro-hardness and porosity tests followed by Grey relational analysis of the results

Investigation of the friction behavior of plasma spray Mo/NiCrBSi coated brake discs

2021 ◽  
Vol 63 (3) ◽  
pp. 259-265
Author(s):  
Halil Kılıç ◽  
Cenk Mısırlı ◽  
İbrahim Mutlu
Keyword(s):  
Coefficient Of Friction ◽  
Plasma Spray ◽  
Wear Behavior ◽  
Atmospheric Plasma ◽  
Brake Disc ◽  
Friction Behavior ◽  
Braking Performance ◽  
Spray Process ◽  
The Coefficient Of Friction ◽  
Nicrbsi Coating

Abstract This paper presents the findings of comparative research conducted to find out the braking performance of a Mo/NiCrBSi coated automobile brake disc. The friction and wear behavior of the Mo/NiCrBSi coating (CD) used for the disc material was evaluated using a laboratory scale disc-pad dynamometer and compared with a reference disc (RD). The coating was deposited by means of the atmospheric plasma spray process on a grey cast iron substrate. Braking tests were performed according to the SAE-J2430 test standard. Disc microstructures were characterized by SEM and XRD. It was found that the bonding strength was good with an infinite rating between the accumulated coating layer and the substrate. The results show that the coated brake disc has a comparable coefficient of friction and that the amount of wear is lower than that of the reference disc. The addition of ductile phases to the disc coating was beneficial in reducing the coefficient of friction to an acceptable degree and also effectively improving wear resistance.

Comparative analysis of tribological behavior of plasma- and high-velocity oxygen fuel-sprayed WC-10Co-4Cr coatings

2017 ◽  
Vol 69 (2) ◽  
pp. 325-332 ◽  
Author(s):  
Shiyu Cui ◽  
Qiang Miao ◽  
Wenping Liang ◽  
Yi Xu ◽  
Baiqiang Li
Keyword(s):  
Plasma Spraying ◽  
High Velocity ◽  
Wear Mechanisms ◽  
Wear Behavior ◽  
High Velocity Oxygen Fuel ◽  
Hvof Spraying ◽  
Content Type ◽  
Q235 Steel ◽  
Oxygen Fuel ◽  
Sprayed Coatings

Purpose The purpose of this study is to prepare WC-10Co-4Cr coatings using two processes of plasma spraying and high-velocity oxygen fuel (HVOF) spraying. The decarburization behaviors of the different processes are analyzed individually. The microstructural characteristics of the as-sprayed coatings are presented and the wear mechanisms of the different WC–10Co–4Cr coatings are discussed in detail. Design/methodology/approach The WC–10Co–4Cr coatings were formed on the surface of Q235 steel by plasma and HVOF spraying. Findings Plasma spraying causes more decarburizing decomposition of the WC phase than HVOF spraying. In the plasma spraying process, η(Cr25Co25W8C2) phase appears and the C content decreases from the top surface of the coating to the substrate. Practical implications In this study, two WC–10Co–4Cr coatings on Q235 steel prepared by plasma and HVOF spraying were compared with respect to the sliding wear behavior. Originality/value The wear mechanisms of the plasma- and HVOF-sprayed coatings were abrasive and oxidation, respectively.

Sign in / Sign up

Export Citation Format

Share Document