Polylactic acid/kenaf cellulose biocomposite filaments for melt extrusion based-3D printing

Cellulose ◽  
2021 ◽  
Author(s):  
Chuanchom Aumnate ◽  
Niphaphun Soatthiyanon ◽  
Thidarat Makmoon ◽  
Pranut Potiyaraj
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Melt Extrusion

High thermal conductivity polylactic acid composite for 3D printing: Synergistic effect of graphene and alumina

2020 ◽  
Vol 31 (6) ◽  
pp. 1291-1299 ◽  
Author(s):  
Jun Jiang ◽  
Shuangqiao Yang ◽  
Linhuan Li ◽  
Shibing Bai
Keyword(s):  
Thermal Conductivity ◽  
3D Printing ◽  
Synergistic Effect ◽  
Polylactic Acid ◽  
High Thermal Conductivity

Fused Filament Fabrication 3D Printed Polylactic Acid Electroosmotic Pumps

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Liang Wu ◽  
Stephen Beirne ◽  
Joan-Marc Cabot Canyelles ◽  
Brett Paull ◽  
Gordon G. Wallace ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Fused Filament Fabrication ◽  
Flexible Approach ◽  
Electroosmotic Pump ◽  
3D Printed ◽  
Electroosmotic Pumps

Additive manufacturing (3D printing) offers a flexible approach for the production of bespoke microfluidic structures such as the electroosmotic pump. Here a readily accessible fused filament fabrication (FFF) 3D printing...

3D-printing in forensic electrochemistry: Atropine determination in beverages using an additively manufactured graphene-polylactic acid electrode

2021 ◽  
pp. 106324
Author(s):  
Afonso F. João ◽  
Raquel G. Rocha ◽  
Tiago A. Matias ◽  
Eduardo M. Richter ◽  
João Flávio S. Petruci ◽  
...  
Keyword(s):  
3D Printing ◽  
Polylactic Acid

scholarly journals Supercritical Impregnation of PLA Filaments with Mango Leaf Extract to Manufacture Functionalized Biomedical Devices by 3D Printing

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2125
Author(s):  
José María Rosales ◽  
Cristina Cejudo ◽  
Lidia Verano ◽  
Lourdes Casas ◽  
Casimiro Mantell ◽  
...  
Keyword(s):  
Antioxidant Activity ◽  
3D Printing ◽  
Polylactic Acid ◽  
Leaf Extract ◽  
Three Dimensional ◽  
3D Printer ◽  
Pharmacological Properties ◽  
Bioactive Properties ◽  
Supercritical Impregnation ◽  
Mango Leaves

Polylactic Acid (PLA) filaments impregnated with ethanolic mango leaves extract (MLE) with pharmacological properties were obtained by supercritical impregnation. The effects of pressure, temperature and amount of extract on the response variables, i.e., swelling, extract loading and bioactivity of the PLA filaments, were determined. The analysis of the filaments biocapacities revealed that impregnated PLA filaments showed 11.07% antidenaturant capacity and 88.13% antioxidant activity, which after a 9-day incubation shifted to 30.10% and 9.90%, respectively. Subsequently, the same tests were conducted on printed samples. Before their incubation, the printed samples showed 79.09% antioxidant activity and no antidenaturant capacity was detected. However, after their incubation, the antioxidant activity went down to only 2.50%, while the antidenaturant capacity raised up to 23.50%. The persistence of the bioactive properties after printing opens the possibility of using the functionalized PLA filaments as the feed for a three-dimensional (3D) printer.

Effect of silane coupling on the properties of polylactic acid/barium ferrite magnetic composite filament for the 3D printing process

2021 ◽  
pp. 50965
Author(s):  
Kankavee Sukthavorn ◽  
Natkritta Phengphon ◽  
Nollapan Nootsuwan ◽  
Pongsakorn Jantaratana ◽  
Chatchai Veranitisagul ◽  
...  
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Barium Ferrite ◽  
Magnetic Composite ◽  
Printing Process ◽  
Silane Coupling ◽  
Composite Filament

The Influence of the 3D Printing Infill and Printing Direction on Friction and Wear of Polylactic Acid (PLA) under Rotational Sliding

2021 ◽  
Vol 42 (2) ◽  
pp. 106-111
Author(s):  
F. Zivic ◽  
S. Mitrovic ◽  
N. Grujovic ◽  
Z. Jovanovic ◽  
D. Dzunic ◽  
...  
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Friction And Wear ◽  
Printing Direction

Thermal, structural, and mechanical effects of nanofibrillated cellulose in polylactic acid filaments for additive manufacturing

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7954-7964
Author(s):  
Diego Gomez-Maldonado ◽  
Maria Soledad Peresin ◽  
Christina Verdi ◽  
Guillermo Velarde ◽  
Daniel Saloni
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Modulus Of Elasticity ◽  
Manufacturing Process ◽  
Thermal Characterization ◽  
Nanofibrillated Cellulose ◽  
Small Decrease ◽  
The Matrix

As the additive manufacturing process gains worldwide importance, the need for bio-based materials, especially for in-home polymeric use, also increases. This work aims to develop a composite of polylactic acid (PLA) and nanofibrillated cellulose (NFC) as a sustainable approach to reinforce the currently commercially available PLA. The studied materials were composites with 5 and 10% NFC that were blended and extruded. Mechanical, structural, and thermal characterization was made before its use for 3D printing. It was found that the inclusion of 10% NFC increased the modulus of elasticity in the filaments from 2.92 to 3.36 GPa. However, a small decrease in tensile strength was observed from 55.7 to 50.8 MPa, which was possibly due to the formation of NFC aggregates in the matrix. This work shows the potential of using PLA mixed with NFC for additive manufacturing.

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

scholarly journals Advanced Pharmaceutical Applications of Hot-Melt Extrusion Coupled with Fused Deposition Modelling (FDM) 3D Printing for Personalised Drug Delivery

Pharmaceutics ◽  
2018 ◽  
Vol 10 (4) ◽  
pp. 203 ◽  
Author(s):  
Deck Tan ◽  
Mohammed Maniruzzaman ◽  
Ali Nokhodchi
Keyword(s):  
3D Printing ◽  
Hot Melt Extrusion ◽  
Pharmaceutical Products ◽  
Fused Deposition Modelling ◽  
Melt Extrusion ◽  
3D Object ◽  
3D Printing Technology ◽  
Fused Deposition ◽  
Pharmaceutical Applications ◽  
Hot Melt

Three-dimensional printing, also known as additive manufacturing, is a fabrication process whereby a 3D object is created layer-by-layer by depositing a feedstock material such as thermoplastic polymer. The 3D printing technology has been widely used for rapid prototyping and its interest as a fabrication method has grown significantly across many disciplines. The most common 3D printing technology is called the Fused Deposition Modelling (FDM) which utilises thermoplastic filaments as a starting material, then extrudes the material in sequential layers above its melting temperature to create a 3D object. These filaments can be fabricated using the Hot-Melt Extrusion (HME) technology. The advantage of using HME to manufacture polymer filaments for FDM printing is that a homogenous solid dispersion of two or more pharmaceutical excipients i.e., polymers can be made and a thermostable drug can even be introduced in the filament composition, which is otherwise impractical with any other techniques. By introducing HME techniques for 3D printing filament development can improve the bioavailability and solubility of drugs as well as sustain the drug release for a prolonged period of time. The latter is of particular interest when medical implants are considered via 3D printing. In recent years, there has been increasing interest in implementing a continuous manufacturing method on pharmaceutical products development and manufacture, in order to ensure high quality and efficacy with less batch-to-batch variations of the pharmaceutical products. The HME and FDM technology can be combined into one integrated continuous processing platform. This article reviews the working principle of Hot Melt Extrusion and Fused Deposition Modelling, and how these two technologies can be combined for the use of advanced pharmaceutical applications.

scholarly journals DESIGN OF A 3D-PRINTED THREE-CLAW ROBOTIC GRIPPER END-EFFECTOR

2021 ◽  
Vol 11 (4) ◽  
pp. 70-79
Author(s):  
Dino Dominic Forte Ligutan ◽  
Argel Alejandro Bandala ◽  
Jason Limon Española ◽  
Richard Josiah Calayag Tan Ai ◽  
Ryan Rhay Ponce Vicerra ◽  
...  
Keyword(s):  
3D Printing ◽  
Polylactic Acid ◽  
Grip Force ◽  
Thermoplastic Polyurethane ◽  
Robotic Arm ◽  
End Effector ◽  
Design Considerations ◽  
3D Printed ◽  
Materials Used ◽  
Metal Work

The development of a novel 3D-printed three-claw robotic gripper shall be described in this paper with the goal of incorporating various design considerations. Such considerations include the grip reliability and stability, grip force maximization, wide object grasping capability. Modularization of its components is another consideration that allows its parts to be easily machined and reusable. The design was realized by 3D printing using a combination of tough polylactic acid (PLA) material and thermoplastic polyurethane (TPU) material. In practice, additional tolerances were also considered for 3D printing of materials to compensate for possible expansion or shrinkage of the materials used to achieve the required functionality. The aim of the study is to explore the design and eventually deploy the three-claw robotic gripper to an actual robotic arm once its metal work fabrication is finished.

Sign in / Sign up

Export Citation Format

Share Document