Multi-Criteria Selection of Quantitative Composition of Alloying Elements of Maraging Steels of the Fe–Cr–Ni–Mo System with an Improved Set of Mechanical Properties

Metallurgist ◽  
2021 ◽  
Author(s):  
D. A. Dvoynikov ◽  
S. V. Gladkovsky
Keyword(s):  
Mechanical Properties ◽  
Alloying Elements ◽  
Quantitative Composition ◽  
Maraging Steels ◽  
Selection Of

Elaboration and Characterization of the Properties of Refractory Cr Base Alloys

2010 ◽  
Vol 72 ◽  
pp. 46-52 ◽  
Author(s):  
Laurent Royer ◽  
Stéphane Mathieu ◽  
Christophe Liebaut ◽  
Pierre Steinmetz
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Molten Glass ◽  
Energy Production ◽  
Creep Properties ◽  
Refractory Alloys ◽  
Industrial Use ◽  
Kinetics Of ◽  
Selection Of

For energy production and also for the glass industry, finding new refractory alloys which could permit to increase the process temperatures to 1200°C or more is a permanent challenge. Chromium base alloys can be good candidates, considering the melting point of Cr itself, and also its low corrosion rate in molten glass. Two families of alloys have been studied for this purpose, Cr-Mo-W and Cr-Ta-X alloys (X= Mo, Si..). A finer selection of compositions has been done, to optimize their chemical and mechanical properties. Kinetics of HT oxidation by air, of corrosion by molten glass and also creep properties of several alloys have been measured up to 1250°C. The results obtained with the best alloys (Cr-Ta base) give positive indications as regards the possibility of their industrial use.

scholarly journals Advances in Fabricating the Electrospun Biopolymer-Based Biomaterials

2021 ◽  
Vol 12 (2) ◽  
pp. 26
Author(s):  
Sebastian Wilk ◽  
Aleksandra Benko
Keyword(s):  
Mechanical Properties ◽  
Whey Protein ◽  
Antimicrobial Properties ◽  
Protein Isolate ◽  
Review Article ◽  
Animal Tissues ◽  
Green Material ◽  
Good Potential ◽  
Fibrous Morphology ◽  
Selection Of

Biopolymers formed into a fibrous morphology through electrospinning are of increasing interest in the field of biomedicine due to their intrinsic biocompatibility and biodegradability and their ability to be biomimetic to various fibrous structures present in animal tissues. However, their mechanical properties are often unsatisfactory and their processing may be troublesome. Thus, extensive research interest is focused on improving these qualities. This review article presents the selection of the recent advances in techniques aimed to improve the electrospinnability of various biopolymers (polysaccharides, polynucleotides, peptides, and phospholipids). The electrospinning of single materials, and the variety of co-polymers, with and without additives, is covered. Additionally, various crosslinking strategies are presented. Examples of cytocompatibility, biocompatibility, and antimicrobial properties are analyzed. Special attention is given to whey protein isolate as an example of a novel, promising, green material with good potential in the field of biomedicine. This review ends with a brief summary and outlook for the biomedical applicability of electrospinnable biopolymers.

scholarly journals A Short Review on the Phase Structures, Oxidation Kinetics, and Mechanical Properties of Complex Ti-Al Alloys

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1677
Author(s):  
Hooi Peng Lim ◽  
Willey Yun Hsien Liew ◽  
Gan Jet Hong Melvin ◽  
Zhong-Tao Jiang
Keyword(s):  
Mechanical Properties ◽  
Oxidation Kinetics ◽  
Mass Gain ◽  
Short Review ◽  
Al Alloys ◽  
Alloying Elements ◽  
Isothermal Exposure ◽  
Solid Solution Strengthening ◽  
Phase Structures ◽  
Solution Strengthening

This paper reviews the phase structures and oxidation kinetics of complex Ti-Al alloys at oxidation temperatures in the range of 600–1000 °C. The mass gain and parabolic rate constants of the alloys under isothermal exposure at 100 h (or equivalent to cyclic exposure for 300 cycles) is compared. Of the alloying elements investigated, Si appeared to be the most effective in improving the oxidation resistance of Ti-Al alloys at high temperatures. The effect of alloying elements on the mechanical properties of Ti-Al alloys is also discussed. Significant improvement of the mechanical properties of Ti-Al alloys by element additions has been observed through the formation of new phases, grain refinement, and solid solution strengthening.

Effect of Small Iron, Chromium and Boron Additions as Alloying Elements on Microstructure and Mechanical Properties of Ni3Al

2007 ◽  
Vol 23 ◽  
pp. 123-126
Author(s):  
Radu L. Orban ◽  
Mariana Lucaci
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Room Temperature ◽  
Alloying Elements ◽  
Alloyed Powder ◽  
Mechanically Alloyed ◽  
Powder Mixtures ◽  
B Additions ◽  
Strength And Ductility ◽  
Iron Chromium

This paper investigates the effect of Fe, Cr and B additions, in small proportions, as alloying elements in Ni3Al with the purpose to reduce its intrinsic fragility and extrinsic embrittlement and to enhance, in the same time, its mechanical properties. It represents a development of some previous research works of the authors, proving that Ni3Al-Fe-Cr-B alloys obtained by reactive synthesis (SHS) starting from Mechanically Alloyed powder mixtures have superior both room temperature tensile strength and ductility, and compression ones at temperatures up to 800 °C, than pure Ni3Al. These create premises for their using as superalloys substitutes.

scholarly journals Mechanical properties of dental restorative materials: relative contribution of laboratory tests

2003 ◽  
Vol 11 (3) ◽  
pp. 162-167 ◽  
Author(s):  
Linda Wang ◽  
Paulo Henrique Perlatti D'Alpino ◽  
Lawrence Gonzaga Lopes ◽  
José Carlos Pereira
Keyword(s):  
Mechanical Properties ◽  
Laboratory Tests ◽  
Clinical Performance ◽  
Dental Materials ◽  
Correct Selection ◽  
Relative Contribution ◽  
Dental Restorative Materials ◽  
Restorative Materials ◽  
Dental Restorative ◽  
Selection Of

A wide variety of dental products that are launched on the market becomes the correct selection of these materials a difficult task. Although the mechanical properties do not necessarily represent their actual clinical performance, they are used to guide the effects of changes in their composition or processing on these properties. Also, these tests might help somehow the clinician to choose once comparisons between former formulations and new ones, as well as, with the leading brand, are highlighted by manufactures. This paper presents a review of the most important laboratory tests. In this manner, the knowledge of these tests will provide a critical opinion related to the properties of different dental materials.

scholarly journals The impact of the health condition of oaks from the Krotoszyn Plateau on the mechanical properties of timber structures

2015 ◽  
Vol 57 (4) ◽  
pp. 224-232
Author(s):  
Jarosław Siwiński ◽  
Katarzyna Kubiak ◽  
Miłosz Tkaczyk ◽  
Anna Mazur ◽  
Ryszard Rekucki
Keyword(s):  
Mechanical Properties ◽  
Health Condition ◽  
Health State ◽  
Timber Structures ◽  
Strength Parameters ◽  
Modified Method ◽  
Strength Tests ◽  
Prior Selection ◽  
The Impact ◽  
Selection Of

Abstract The study was conducted to perform a comparative analysis of the mechanical properties of wood samples derived from oaks in the Krotoszyn Plateau, which depend on the health state of the trees. Strength parameters of oak wood were calculated for selected diseased and healthy trees (according to the Roloff classification). The study was conducted by a modified method described in the standard Polish Norm PN EN 408+ A1: 2012. For testing, prior selection of wood samples showed that more wood samples of diseased trees compared with those of healthy oaks did not fulfil the Polish standard requirements. According to the method used, the average results of strength tests of timber structures from healthy oaks exhibited higher strength parameters than those of the diseased trees.

Sign in / Sign up

Export Citation Format

Share Document