Influences of plant spacing on root tensile strength of Schefflera arboricola and soil shear strength

2019 ◽  
Vol 15 (2) ◽  
pp. 223-230 ◽  
Author(s):  
J. J. Ni ◽  
A. K. Leung ◽  
C. W. W. Ng
2008 ◽  
Vol 305 (1-2) ◽  
pp. 207-226 ◽  
Author(s):  
S. De Baets ◽  
J. Poesen ◽  
B. Reubens ◽  
K. Wemans ◽  
J. De Baerdemaeker ◽  
...  

2018 ◽  
Vol 426 (1-2) ◽  
pp. 429-430 ◽  
Author(s):  
S. De Baets ◽  
J. Poesen ◽  
B. Reubens ◽  
K. Wemans ◽  
J. De Baerdemaeker ◽  
...  

2021 ◽  
Author(s):  
Alessandro Fraccica ◽  
Enrique Romero ◽  
Thierry Fourcaud

<p>Soil tensile strength plays an important role in the hydro-mechanical behaviour of earth structures and slopes interacting with the atmosphere. Shrinkage-induced cracking may be generated by drying/wetting cycles, with consequent faster water infiltration from the top of slopes and reduction of the safety factor. Vegetation roots were proven to increase soil shear strength, but less is known about their effects on soil tensile strength. For this purpose, new equipment has been designed and used to induce plant growth in compacted soil samples and to perform uniaxial tensile tests on the reinforced material. The equipment is composed of two cylindrical moulds linked by a soil bridge in which the tensile crack is induced due to geometrical restraints.</p><p>For this study, silty sand was chosen and compacted at a low dry density (ρ<sub>d</sub> = 1.60 Mg/m<sup>3</sup>) and at a water content w = 15%. After compaction, samples were gently poured with water up to a high degree of saturation (S<sub>r</sub> ≈ 0.95) and low suction (s ≈ 1 kPa). Then, six of them were seeded with Cynodon dactilon, adopting fixed seeding density and spacing. Plants were irrigated and let to grow for three months: during this period, suction was monitored by a tensiometer. Seven fallow specimens were prepared following the same procedure, for comparison purposes.</p><p>When ready, samples were dried in a temperature/relative humidity-controlled room and left in the darkness for three hours, to attain and equalise the desired value of initial suction. Finally, the tensile stress was induced on the soil by a displacement rate of 0.080 mm/min. For each test, suction was continuously monitored by a tensiometer while the water content was checked at the beginning and at the end. Moreover, the void ratio and the root volume and area ratio were assessed close to the crack generated, at the end of each test.</p><p>The hydraulic state affected the soil mechanical response upon uniaxial extension: an increase of strength and a more brittle behaviour were observed as suction was increasing. At the same suction, a higher strength was systematically observed in the vegetated soil. In fact, even at very low suction (i.e. s = 1 kPa), vegetation roots induced a considerable increase in soil tensile strength (i.e. 10 kPa). The soil hydraulic state also affected the root failure mechanism. In wet soil, the roots subjected to tension were stretched and pulled-out whereas in dry soil they experienced a more immediate breakage (i.e. in concomitance with the cracking of the surrounding soil). Some preliminary PIV (Particle Image Velocimetry) analyses showed differences among dry/wet and fallow/vegetated soils. Indeed, a more diffuse strain field was observed in vegetated samples, thanks to the redistribution of stresses induced by the roots.</p><p>Results were successfully interpreted by a well-established shear strength criterion for partially saturated soils, considering the degree of saturation, suction and soil microstructure. An increase of the soil shear strength was observed and correlated to the presence of roots and to their geometrical and mechanical features. Moreover, good consistency was detected with results coming from other equipment.</p><p> </p>


Alloy Digest ◽  
1981 ◽  
Vol 30 (8) ◽  

Abstract CENTRI-CAST GRAY IRON 50 is a centrifugally cast gray iron with a nominal tensile strength of 50,000 psi. It is cast in the form of tubing which has a wide range of uses in applications where size and shape are of paramount importance and freedom from pattern cost is an important consideration. Among its many applications are farm machinery, seals, bushings, machine tools and general machinery uses. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on casting, heat treating, machining, and surface treatment. Filing Code: CI-51. Producer or source: Federal Bronze Products Inc..


Alloy Digest ◽  
1979 ◽  
Vol 28 (9) ◽  

Abstract CENTRI-CAST GRAY IRON 55 is a centrifugally cast gray iron with a nominal tensile strength of 55,000 psi. It is produced in the form of tubing which has a wide range of uses in applications where size and shape are of paramount importance and freedom from pattern cost is an important consideration. Typical applications are seals, bushings, farm machinery, casings and general machinery uses. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on casting, heat treating, machining, and surface treatment. Filing Code: CI-48. Producer or source: Federal Bronze Products Inc..


Author(s):  
Andrew Lees ◽  
Michael Dobie

Polymer geogrid reinforced soil retaining walls have become commonplace, with routine design generally carried out by limiting equilibrium methods. Finite element analysis (FEA) is becoming more widely used to assess the likely deformation behavior of these structures, although in many cases such analyses over-predict deformation compared with monitored structures. Back-analysis of unit tests and instrumented walls improves the techniques and models used in FEA to represent the soil fill, reinforcement and composite behavior caused by the stabilization effect of the geogrid apertures on the soil particles. This composite behavior is most representatively modeled as enhanced soil shear strength. The back-analysis of two test cases provides valuable insight into the benefits of this approach. In the first case, a unit cell was set up such that one side could yield thereby reaching the active earth pressure state. Using FEA a test without geogrid was modeled to help establish appropriate soil parameters. These parameters were then used to back-analyze a test with geogrid present. Simply using the tensile properties of the geogrid over-predicted the yield pressure but using an enhanced soil shear strength gave a satisfactory comparison with the measured result. In the second case a trial retaining wall was back-analyzed to investigate both deformation and failure, the failure induced by cutting the geogrid after construction using heated wires. The closest fit to the actual deformation and failure behavior was provided by using enhanced fill shear strength.


2014 ◽  
Vol 635-637 ◽  
pp. 750-754
Author(s):  
Peng Hu ◽  
Qing Li ◽  
Yi Wei Xu ◽  
Nan Ying Shentu ◽  
Quan Yuan Peng

Expound the importance of soil shear strength measurement at mudslide hidden point to release the loss caused by the disaster, explain the relationship between shear wave velocity, moisture content and shear strength, design the shear strength monitoring system combining the shear wave velocity measured by Piezoelectric bender elements and moisture content.


Sign in / Sign up

Export Citation Format

Share Document