Microstructural stability of rapidly-solidified CuB alloys

1988 ◽  
Vol 98 ◽  
pp. 161-164 ◽  
Author(s):  
E. Batawi ◽  
M.A. Morris ◽  
D.G. Morris
Keyword(s):  
Microstructural Stability ◽  
Rapidly Solidified

Microstructural stability in rapidly solidified ternary iron aluminides

1990 ◽  
Vol 48 (4) ◽  
pp. 988-989
Author(s):  
Allan J. Morton ◽  
Brigitte Décamps ◽  
Mark A. Gibson ◽  
Alan Wolfenden
Keyword(s):  
Grain Size ◽  
Cross Sections ◽  
Elevated Temperatures ◽  
Low Cost ◽  
Strip Thickness ◽  
Iron Aluminides ◽  
Grain Structure ◽  
Microstructural Stability ◽  
Cast Strip ◽  
Rapidly Solidified

Iron aluminides containing ternary additions of Cr, Si and other alloying elements offer good oxidation and sulphidation resistance at a relatively low cost but these alloys have only moderate strength at elevated temperatures and are of limited ductility. The generation of a distribution of fine dispersoids throughout the matrix of these alloys can provide increased strength and also improve ductility by reducing grain size.We report a study of the microstructural stability of rapidly solidified strip of iron aluminides containing chromium and minor additions of both titanium and boron. As cast strip thickness was in the range 80-120μm.Figure 1 shows the grain structure near the centre of the as cast strip of a 66.5Fe-28.5Al-5.0Cr (at.%) alloy. The grain size in this view of the strip is quite small (2-5μm) although optical metallography of the longitudinal and transverse cross sections show that the grain structure is columnar through much of the strip thickness.

scholarly journals Effect of Aging Treatment on Microstructural Evolution of Rapidly Solidified Eutectic Sn-Pb Alloy Powders

2019 ◽  
Vol 9 (3) ◽  
pp. 392 ◽  
Author(s):  
Jianfeng Yan ◽  
Dezhi Zhu ◽  
Yingjie Liu ◽  
Jun Xu
Keyword(s):  
Elevated Temperatures ◽  
Aging Treatment ◽  
Microstructural Stability ◽  
Rich Phase ◽  
Phase Coarsening ◽  
Coarsening Behavior ◽  
Alloy Solder ◽  
Different Temperatures ◽  
Rate Kinetics ◽  
Rapidly Solidified

The microstructural stability of rapidly solidified eutectic Sn–Pb alloy solder powders was investigated through aging at room temperature (25 °C) and temperatures of 40 °C–120 °C. The coarsening behavior of the Pb-rich phase both at room and elevated temperatures was observed. The evident coarsening of the Pb-rich phase was detected upon storage after 40 days. At elevated temperatures, a similar sequence of Pb-rich phase coarsening was observed; however, it occurred substantially more quickly. Pb-rich coarsening rate kinetics at different temperatures were estimated using the Arrhenius equation. The apparent activation energy was 45.53 ± 4.23 KJ/mol, which indicates that grain boundary diffusion is a crucial mass transport mechanism controlling Pb-rich phase coarsening under annealing.

An investigation on the microstructural stability of rapidly solidified AlFeVSi alloy ribbon

1994 ◽  
Vol 179-180 ◽  
pp. 412-415 ◽  
Author(s):  
Jian-Qiang Wang ◽  
Mei-Kuang Tseng ◽  
Xiu-Fang Chen ◽  
Bao-Jin Zhang ◽  
Ze Xianyu
Keyword(s):  
Alloy Ribbon ◽  
Microstructural Stability ◽  
Rapidly Solidified

Suppression of γ’ Precipitation in a Laser-Melted Nickel-Base Alloy

1977 ◽  
Vol 35 ◽  
pp. 270-271
Author(s):  
J. M. Walsh ◽  
J. C. Whittles ◽  
B. H. Kear ◽  
E. M. Breinan
Keyword(s):  
Cooling Rate ◽  
Base Alloy ◽  
Material Surface ◽  
Intimate Contact ◽  
Absorbed Power ◽  
Perfect Contact ◽  
Nickel Base ◽  
Rapidly Solidified ◽  
Limiting Case ◽  
The Heat Transfer Coefficient

Conventionally cast γ’ precipitation hardened nickel-base superalloys possess well-defined dendritic structures and normally exhibit pronounced segregation. Splat quenched, or rapidly solidified alloys, on the other hand, show little or no evidence for phase decomposition and markedly reduced segregation. In what follows, it is shown that comparable results have been obtained in superalloys processed by the LASERGLAZE™ method.In laser glazing, a sharply focused laser beam is traversed across the material surface at a rate that induces surface localized melting, while avoiding significant surface vaporization. Under these conditions, computations of the average cooling rate can be made with confidence, since intimate contact between the melt and the self-substrate ensures that the heat transfer coefficient is reproducibly constant (h=∞ for perfect contact) in contrast to the variable h characteristic of splat quenching. Results of such computations for pure nickel are presented in Fig. 1, which shows that there is a maximum cooling rate for a given absorbed power density, corresponding to the limiting case in which melt depth approaches zero.

On the Origin of the Microscystalline Structure in Rapidly Solidified IN-100 Powder

1977 ◽  
Vol 35 ◽  
pp. 260-261
Author(s):  
J. M. Walsh ◽  
K. P. Gumz ◽  
J. C. Whittles ◽  
B. H. Kear
Keyword(s):  
The Other ◽  
Coarse Grained ◽  
Microcrystalline Structure ◽  
Routine Examination ◽  
Atomization Process ◽  
Centrifugal Atomization ◽  
Splat Quenching ◽  
Powder Particles ◽  
Dendritic Microstructures ◽  
Rapidly Solidified

During a routine examination of the microstructure of rapidly solidified IN-100 powder, produced by a newly-developed centrifugal atomization process1, essentially two distinct types of microstructure were identified. When a high melt superheat is maintained during atomization, the powder particles are predominantly coarse-grained, equiaxed or columnar, with distinctly dendritic microstructures, Figs, la and 4a. On the other hand, when the melt superheat is reduced by increasing the heat flow to the disc of the rotary atomizer, the powder particles are predominantly microcrystalline in character, with typically one dendrite per grain, Figs, lb and 4b. In what follows, evidence is presented that strongly supports the view that the unusual microcrystalline structure has its origin in dendrite erosion occurring in a 'mushy zone' of dynamic solidification on the disc of the rotary atomizer.The critical observations were made on atomized material that had undergone 'splat-quenching' on previously solidified, chilled substrate particles.

Lorentz electron microscopy of magnetic domains in rapidly solidified and annealed Pt-Co-B alloys

1991 ◽  
Vol 49 ◽  
pp. 784-785
Author(s):  
N. Qiu ◽  
J. E. Wittig
Keyword(s):  
Rapid Solidification ◽  
Ion Beam ◽  
Magnetic Behavior ◽  
High Coercivity ◽  
Magnetic Domains ◽  
Beam Angle ◽  
Tem Analysis ◽  
Intrinsic Coercivity ◽  
Hard Magnets ◽  
Rapidly Solidified

PtCo hard magnets have specialized applications owing to their relatively high coercivity combined with corrosion resistance and ductility. Increased intrinsic coercivity has been recently obtained by rapid solidification processing of PtCo alloys containing boron. After rapid solidification by double anvil splat quenching and subsequent annealing for 30 minutes at 650°C, an alloy with composition Pt42Co45B13 (at.%) exhibited intrinsic coercivity up to 14kOe. This represents a significant improvement compared to the average coercivities in conventional binary PtCo alloys of 5 to 8 kOe.Rapidly solidified specimens of Pt42Co45B13 (at.%) were annealed at 650°C and 800°C for 30 minutes. The magnetic behavior was characterized by measuring the coercive force (Hc). Samples for TEM analysis were mechanically thinned to 100 μm, dimpled to about 30 nm, and ion milled to electron transparency in a Gatan Duomill at 5 kV and 1 mA gun current. The incident ion beam angle was set at 15° and the samples were liquid nitrogen cooled during milling. These samples were analyzed with a Philips CM20T TEM/STEM operated at 200 kV.

Microstructural characterization of a rapidly solidified Al-Fe-V-Si alloy for elevated temperature applications

1988 ◽  
Vol 46 ◽  
pp. 550-551
Author(s):  
R. E. Franck ◽  
J. A. Hawk ◽  
G. J. Shiflet
Keyword(s):  
High Temperature ◽  
Elevated Temperature ◽  
Grain Growth ◽  
Volume Fraction ◽  
Microstructural Characterization ◽  
Second Phase ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Temperature Applications

Rapid solidification processing (RSP) is one method of producing high strength aluminum alloys for elevated temperature applications. Allied-Signal, Inc. has produced an Al-12.4 Fe-1.2 V-2.3 Si (composition in wt pct) alloy which possesses good microstructural stability up to 425°C. This alloy contains a high volume fraction (37 v/o) of fine nearly spherical, α-Al12(Fe, V)3Si dispersoids. The improved elevated temperature strength and stability of this alloy is due to the slower dispersoid coarsening rate of the silicide particles. Additionally, the high v/o of second phase particles should inhibit recrystallization and grain growth, and thus reduce any loss in strength due to long term, high temperature annealing.The focus of this research is to investigate microstructural changes induced by long term, high temperature static annealing heat-treatments. Annealing treatments for up to 1000 hours were carried out on this alloy at 500°C, 550°C and 600°C. Particle coarsening and/or recrystallization and grain growth would be accelerated in these temperature regimes.

Microstructural Variations in Melt-Spun Rapidly Solidified Ribbons

1985 ◽  
Vol 43 ◽  
pp. 54-55
Author(s):  
L. A. Bendersky ◽  
W. J. Boettinger
Keyword(s):  
Solid State ◽  
Processing Parameters ◽  
Heat Extraction ◽  
Solid State Reactions ◽  
Careful Examination ◽  
Ion Milling ◽  
Melt Spun ◽  
Wheel Side ◽  
Rapidly Solidified ◽  
Heat Extraction Rate

Rapid solidification produces a wide variety of sub-micron scale microstructure. Generally, the microstructure depends on the imposed melt undercooling and heat extraction rate. The microstructure can vary strongly not only due to processing parameters changes but also during the process itself, as a result of recalescence. Hence, careful examination of different locations in rapidly solidified products should be performed. Additionally, post-solidification solid-state reactions can alter the microstructure.The objective of the present work is to demonstrate the strong microstructural changes in different regions of melt-spun ribbon for three different alloys. The locations of the analyzed structures were near the wheel side (W) and near the center (C) of the ribbons. The TEM specimens were prepared by selective electropolishing or ion milling.

Spherulite Structures in a Melt Spun Fe-Ni Austenitic Steel

1985 ◽  
Vol 43 ◽  
pp. 52-53
Author(s):  
G. M. Michal ◽  
T. K. Glasgow ◽  
T. J. Moore
Keyword(s):  
Austenitic Steel ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Large Range ◽  
Amorphous Structure ◽  
Nucleation And Growth ◽  
Ni Alloys ◽  
Melt Spun ◽  
Crystal Fibers ◽  
Rapidly Solidified

Large additions of B to Fe-Ni alloys can lead to the formation of an amorphous structure, if the alloy is rapidly cooled from the liquid state to room temperature. Isothermal aging of such structures at elevated temperatures causes crystallization to occur. Commonly such crystallization pro ceeds by the nucleation and growth of spherulites which are spherical crystalline bodies of radiating crystal fibers. Spherulite features were found in the present study in a rapidly solidified alloy that was fully crysstalline as-cast. This alloy was part of a program to develop an austenitic steel for elevated temperature applications by strengthening it with TiB2. The alloy contained a relatively large percentage of B, not to induce an amorphous structure, but only as a consequence of trying to obtain a large volume fracture of TiB2 in the completely processed alloy. The observation of spherulitic features in this alloy is described herein. Utilization of the large range of useful magnifications obtainable in a modern TEM, when a suitably thinned foil is available, was a key element in this analysis.

Sign in / Sign up

Export Citation Format

Share Document