Evolution of microstructure during annealing of Mn1.5Co1.5O4 spinel coatings deposited by atmospheric plasma spray

2014 ◽  
Vol 39 (25) ◽  
pp. 13844-13851 ◽  
Author(s):  
Ying-Zhen Hu ◽  
Cheng-Xin Li ◽  
Guan-Jun Yang ◽  
Chang-Jiu Li
Keyword(s):  
Plasma Spray ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Evolution Of Microstructure

Fabrication and Ablation Behavior of Plasma Sprayed ZrC-W Composite Coatings

2014 ◽  
Vol 602-603 ◽  
pp. 552-555
Author(s):  
Dan Lu ◽  
Ya Ran Niu ◽  
Xue Lian Ge ◽  
Xue Bing Zheng ◽  
Guang Chen
Keyword(s):  
Thermal Conductivity ◽  
Thermal Shock ◽  
Plasma Spray ◽  
Composite Coatings ◽  
Lamellar Microstructure ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Plasma Flame ◽  
Plasma Sprayed ◽  
Zrc Coating

In this work, atmospheric plasma spray (APS) technology was applied to fabricate ZrC-W composite coatings. The microstructure of the composite coatings was characterized. The influence of W content on the ablation-resistant and thermal shock properties of ZrC-W composite coatings was evaluated using a plasma flame. The results show that the ZrC-W composite coatings had typically lamellar microstructure, which was mainly made up of cubic ZrC, cubic W and a small amount of tetragonal ZrO2. The ZrC-W coatings had improved ablation resistant and thermal shock properties compared with those of the pure ZrC coating. It was supposed that the improved density, thermal conductivity and toughness of the composite coatings contributed to this phenomenon.

scholarly journals Mechanical Properties of Strontium–Hardystonite–Gahnite Coating Formed by Atmospheric Plasma Spray

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 759
Author(s):  
Duy Quang Pham ◽  
Christopher C. Berndt ◽  
Ameneh Sadeghpour ◽  
Hala Zreiqat ◽  
Peng-Yuan Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Plasma Spray ◽  
Elastic Moduli ◽  
Cell Attachment ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Wear Volume ◽  
Marrow Mesenchymal Stem Cells ◽  
Good Biocompatibility

In this work, we measured the mechanical properties and tested the cell viability of a bioceramic coating, strontium–hardystonite–gahnite (Sr–HT–G, Sr–Ca2ZnSi2O7–ZnAl2O4), to evaluate potential use of this novel bioceramic for bone regeneration applications. The evaluation of Sr–HT–G coatings deposited via atmospheric plasma spray (APS) onto Ti–6Al–4V substrates have been contrasted to the properties of the well-known commercial standard coating of hydroxyapatite (HAp: Ca10(PO4)6(OH)2). The Sr–HT–G coating exhibited uniform distribution of hardness and elastic moduli across its cross-section; whereas the HAp coating presented large statistical variations of these distributions. The Sr–HT–G coating also revealed higher results of microhardness, nanohardness and elastic moduli than those shown for the HAp coating. The nanoscratch tests for the Sr–HT–G coating presented a low volume of material removal without high plastic deformation, while the HAp coating revealed ploughing behaviour with a large pileup of materials and plastic deformation along the scratch direction. Furthermore, nanoscanning wear tests indicated that Sr–HT–G had a lower wear volume than the HAp coating. The Sr–HT–G coating had slightly higher cell attachment density and spreading area compared to the HAp coating indicating that both coatings have good biocompatibility for bone marrow mesenchymal stem cells (BMSCs).

scholarly journals Graphitization Potential of Cast Iron Powder in Atmospheric Plasma Spray Conditions

2006 ◽  
Vol 47 (7) ◽  
pp. 1710-1716 ◽  
Author(s):  
I. Ozdemir ◽  
Y. Tsunekawa ◽  
M. Okumiya ◽  
T. Ueno
Keyword(s):  
Cast Iron ◽  
Iron Powder ◽  
Plasma Spray ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Cast Iron Powder
Sign in / Sign up

Export Citation Format

Share Document