Optimization of mechanical properties of high strength bainitic steel using thermo-mechanical control and accelerated cooling process

2015 ◽  
Vol 217 ◽  
pp. 202-210 ◽  
Author(s):  
Xiangwei Kong ◽  
Liangyun Lan ◽  
Zhiyong Hu ◽  
Bin Li ◽  
Tianzhong Sui
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Accelerated Cooling ◽  
Bainitic Steel ◽  
Cooling Process ◽  
Mechanical Control

Effect of Processing Route on Mechanical Behavior of C-Mn Multiphase High Strength Cold Rolled Steel

2007 ◽  
Vol 539-543 ◽  
pp. 4375-4380
Author(s):  
Dagoberto Brandão Santos ◽  
Élida G. Neves ◽  
Elena V. Pereloma
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Quantitative Relationship ◽  
High Strength ◽  
Microstructural Characterization ◽  
Processing Route ◽  
Accelerated Cooling ◽  
Microstructural Parameters ◽  
Transmission Electron

The multiphase steels have complex microstructures containing polygonal ferrite, martensite, bainite, carbide and a small amount of retained austenite. This microstructure provides these steels with a high mechanical strength and good ductility. Different thermal cycles were simulated in the laboratory in order to create the microstructures with improved mechanical properties. The samples were heated to various annealing temperatures (740, 760 or 780°C), held for 300 s, and then quickly cooled to 600 or 500°C, where they were soaked for another 300 s and then submitted to the accelerated cooling process, with the rates in the range of 12-30°C/s. The microstructure was examined at the end of each processing route. The mechanical behavior evaluation was made by microhardness testing. The microstructural characterization involved optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM). The use of multiple regression analysis allowed the establishment of quantitative relationship between the microstructural parameters, cooling rates and mechanical properties of the steel.

Investigation of Microstructure and Mechanical Properties of Ultra High Strength Bainitic Steel

2013 ◽  
Vol 313-314 ◽  
pp. 77-81
Author(s):  
M.H. Sheikh Ansari ◽  
M. Aghaie-Khafri
Keyword(s):  
Mechanical Properties ◽  
Alloy Steel ◽  
High Strength ◽  
Lower Bainite ◽  
Good Combination ◽  
Bainitic Steel ◽  
Low Alloy Steel ◽  
Tempered Martensite ◽  
Medium Carbon ◽  
Bainitic Steels

In this study, medium carbon low alloy steel was used to obtain bainitic structures. The lower bainite and tempered martensite-lower bainite structures were achieved by isothermal austempering and up quenching treatment, respectively. Based on the results obtained these structures showed a very good combination of strength and toughness. Furthermore, it has been shown that austenitization time and temperature, as well as austempering time and temperature play a major role in achieving ultra-high strength bainitic steels.

Air-Cooled Mn-Series Bainitic Steel as 5Mn2SiNbTi of Grade YS 415 to 550MPa for Seamless Steel Pipe

2011 ◽  
Vol 120 ◽  
pp. 471-474
Author(s):  
Chun Feng ◽  
Zhao Xi Shen ◽  
Yan Kang Zheng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Strength ◽  
Control Rolling ◽  
Air Cooling ◽  
Bainitic Steel ◽  
Medium Temperature ◽  
Final Rolling ◽  
And Control ◽  
Seamless Steel

The mechanical properties and microstructure of Mn-series bainitic steel as 5Mn2SiNbTi after air cooling and tempering have been investigated in this paper. The results show that the investigated steel show high strength (tensile strength up to 671MPa), low toughness (20J at -30°C) after hot rolling (final rolling at 1050°C) and air cooling. Medium temperature tempering can improve the toughness, without sacrificing strength of the steel. After tempering at 450°C for 1h, the steel obtained 632MPa tensile strength, 467MPa yield strength, 140J impact energy at -30°C, remaining 25.0% elongation. It is indicated that the tested steel can gain excellent combination of strength and toughness without precious alloy adding, control rolling and control cooling.

scholarly journals Study of the thermal treatment modes influence on the forming of microstructure and specified complex of mechanical properties of high-strength sheet product with guaranteed level of hardness (400–450 HB) of low-alloyed steel

2019 ◽  
Vol 75 (4) ◽  
pp. 480-487
Author(s):  
M. Yu. Matrosov ◽  
P. G. Martynov ◽  
A. V. Mitrofanov ◽  
K. Yu. Barabash ◽  
T. V. Goroshko ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fine Structure ◽  
Thermal Treatment ◽  
Hot Rolling ◽  
High Strength ◽  
Controlled Rolling ◽  
Alloyed Steel ◽  
Accelerated Cooling ◽  
Cold Forming ◽  
Low Alloyed Steel

High-strength sheet product of low-alloyed steel, used at manufacturing of heavy-loaded structures, must have, apart from wear resistance, high toughness, good weldability, ability to hot and cold forming, machinability and low cost. Combination of these properties based on forming fine grain austenite structure before the martensitic transformation at definite its thermal treatment modes. Results of study of microstructure, fine structure and mechanical properties of high-strength boron-containing low-alloyed steel after different technological methods of the rolled product manufacturing presented: high-temperature hot rolling and twostages controlled rolling with accelerated cooling followed by thermal treatment – quenching with tempering. Variants of optimal modes of thermal treatment determined, providing combination of high level of impact toughness under negative temperatures, hardness and strength properties of sheet product. The two considered in the article technological variants, comprising treatment of low-alloyed steel with boron (hot rolling and two-stages controlled rolling with accelerated cooling) followed by thermal treatment results in forming fine structure of tempered martensite, which provides high mechanical properties, meeting the made requirements. Depending on the heating temperature before quenching in the range 770–950 °С, the morphology of the actual steel grain is changing from elongated to equiaxed, which is connected with the metal recrystallization process during heating after plastic deformation. The study results obtained allow to optimize the thermal treatment processes of sheet product of low-alloyed boron containing steel for particular conditions of application.

scholarly journals Mechanical properties of wire and arc additively manufactured high-strength steel structures

2021 ◽  
Author(s):  
Johanna Müller ◽  
Jonas Hensel ◽  
Klaus Dilger
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
High Strength Steel ◽  
Energy Input ◽  
High Strength ◽  
Accelerated Cooling ◽  
Active Cooling ◽  
Wire Arc Additive Manufacturing ◽  
Interpass Temperature

AbstractAdditive manufacturing with steel opens up new possibilities for the construction sector. Especially direct energy deposition processes like DED-arc, also known as wire arc additive manufacturing (WAAM), is capable of manufacturing large structures with a high degree of geometric freedom, which makes the process suitable for the manufacturing of force flow-optimized steel nodes and spaceframes. By the use of high strength steel, the manufacturing times can be reduced since less material needs to be deposited. To keep the advantages of the high strength steel, the effect of thermal cycling during WAAM needs to be understood, since it influences the phase transformation, the resulting microstructure, and hence the mechanical properties of the material. In this study, the influences of energy input, interpass temperature, and cooling rate were investigated by welding thin walled samples. From each sample, microsections were analyzed, and tensile test and Charpy-V specimens were extracted and tested. The specimens with an interpass temperature of 200 °C, low energy input and applied active cooling showed a tensile strength of ~ 860–900 MPa, a yield strength of 700–780 MPa, and an elongation at fracture between 17 and 22%. The results showed the formation of martensite for specimens with high interpass temperatures which led to low yield and high tensile strengths (Rp0.2 = 520–590 MPa, Rm = 780–940 MPa) for the specimens without active cooling. At low interpass temperatures, the increase of the energy input led to a decrease of the tensile and the yield strength while the elongation at fracture as well as the Charpy impact energy increased. The formation of upper bainite due to the higher energy input can be avoided by accelerated cooling while martensite caused by high interpass temperatures need to be counteracted by heat treatment.

Factors affecting the mechanical properties of ultra-high-strength bainitic steel containing W and 0. 33 mass% C

2016 ◽  
Vol 23 (3) ◽  
pp. 289-296 ◽  
Author(s):  
Shi-meng Zhou ◽  
Xing-wang Cheng ◽  
You-jing Zhang ◽  
Meng Wang ◽  
Wen Jiang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Bainitic Steel ◽  
Factors Affecting

scholarly journals Effect of Cooling and Isothermal Holding on the Amount of Martensite/Austenite (M/A) Constituents, Microstructure and Mechanical Properties of Microalloyed Pipeline Steel

2018 ◽  
Vol 918 ◽  
pp. 152-158 ◽  
Author(s):  
Alexander Kabanov ◽  
Grzegorz Korpala ◽  
Rudolf Kawalla ◽  
Sergey Ionov
Keyword(s):  
Mechanical Properties ◽  
Pipeline Steel ◽  
Isothermal Holding ◽  
High Strength Steels ◽  
High Strength ◽  
Cold Climate ◽  
Throughput Capacity ◽  
Accelerated Cooling ◽  
Bainitic Steels ◽  
Strength And Plasticity

Constant increase of energy consumption in modern industry requires construction of heavily loaded pipelines with high throughput capacity. Therefore, high-strength steels should be used for the cost reasons. Additionally, the pipelines are also often used in the areas with cold climate and high seismicity. Therefore, strength and plasticity reduction is unacceptable. Bainitic steels with retained austenite (RA) or martensite/austenite (M/A) constituents meet these requirements. The purpose of this investigation is to determine thermo-mechanical treatment parameters with further accelerated cooling and additional isothermal holding for M/A-phase and mechanical properties formation. Experimental modeling of the production process was carried out using Gleeble HDS-V40 thermo-mechanical simulator. All investigations were realized with two high-strength micro-alloyed steels with different molybdenum and carbon content. Results showed that decrease of temperature and duration of isothermal holding as well as addition of molybdenum promote bainitic microstructure nucleation and reduce grain size and M/A-constituents. All these factors lead to a slight improvement in mechanical properties.

Process, Microstructure and Mechanical Properties of X90 Pipeline Steel

2016 ◽  
Vol 850 ◽  
pp. 894-898
Author(s):  
Bin Guo ◽  
Jin Qiao Xu ◽  
Lei Cui ◽  
Qing Feng Wang
Keyword(s):  
Mechanical Properties ◽  
Manufacturing Process ◽  
Pipeline Steel ◽  
Structural Characteristics ◽  
High Strength ◽  
Controlled Rolling ◽  
Accelerated Cooling ◽  
Iron And Steel ◽  
Technical Requirements ◽  
China National Petroleum Corporation

This paper provided a detailed description of X90 pipeline steel developed in Wuhan Iron and Steel Corporation (WISCO), including its metallurgical design, manufacturing process, structural characteristics and mechanical properties. Some key issues such as the cooling rate and rolling parameters were addressed for the development of X90 pipeline steel. The experimental results showed that the manufacturing process of controlled rolling (for austenite refining) + relaxation (for ferrite phase transformation) +ultrafast accelerated cooling could guarantee very fine microstructure and excellent mechanical properties. The X90 pipeline steel developed in WISCO has a good match of high strength and excellent toughness. Mechanical properties of X90 coils, plates and corresponding SSAW and LSAW pipes comprehensively meet the technical requirements of China National Petroleum Corporation (CNPC).

Sign in / Sign up

Export Citation Format

Share Document