Investigating the static or dynamic flexural and compressive stresses on flexible tubing: Comparison of clamp and peristaltic pump impact on surface damages and particles leaching during infusion acts

2021 ◽  
Vol 123 ◽  
pp. 104737
Author(s):  
J. Saunier ◽  
N. Yagoubi
Keyword(s):  
Peristaltic Pump ◽  
Compressive Stresses ◽  
Surface Damages

Theoretical study of the prestressing strand's stress by computer modeling methods

2020 ◽  
Vol 76 (11) ◽  
pp. 1139-1148
Author(s):  
A. G. Korchunov ◽  
E. M. Medvedeva ◽  
E. M. Golubchik
Keyword(s):  
Residual Stresses ◽  
High Strength ◽  
Pearlitic Steel ◽  
Internal Stresses ◽  
Steel Microstructure ◽  
Compressive Stresses ◽  
Wide Range ◽  
Prestressing Strands ◽  
Increasing Temperature ◽  
Wire Strand

The modern construction industry widely uses reinforced concrete structures, where high-strength prestressing strands are used. Key parameters determining strength and relaxation resistance are a steel microstructure and internal stresses. The aim of the work was a computer research of a stage-by-stage formation of internal stresses during production of prestressing strands of structure 1х7(1+6), 12.5 mm diameter, 1770 MPa strength grade, made of pearlitic steel, as well as study of various modes of mechanical and thermal treatment (MTT) influence on their distribution. To study the effect of every strand manufacturing operation on internal stresses of its wires, the authors developed three models: stranding and reducing a 7-wire strand; straightening of a laid strand, stranding and MTT of a 7-wire strand. It was shown that absolute values of residual stresses and their distribution in a wire used for strands of a specified structure significantly influence performance properties of strands. The use of MTT makes it possible to control in a wide range a redistribution of residual stresses in steel resulting from drawing and strand laying processes. It was established that during drawing of up to 80% degree, compressive stresses of 1100-1200 MPa degree are generated in the central layers of wire. The residual stresses on the wire surface accounted for 450-500 MPa and were tension in nature. The tension within a range of 70 kN to 82 kN combined with a temperature range of 360-380°С contributes to a two-fold decrease in residual stresses both in the central and surface layers of wire. When increasing temperature up to 400°С and maintaining the tension, it is possible to achieve maximum balance of residual stresses. Stranding stresses, whose high values entail failure of lay length and geometry of the studied strand may be fully eliminated only at tension of 82 kN and temperature of 400°С. Otherwise, stranding stresses result in opening of strands.

INTERACTION OF STRONG COMPRESSIVE STRESSES WITH TOPOGRAPHY: IMPLICATIONS FOR BEDROCK FRACTURES IN FORSMARK, SWEDEN

2017 ◽  
Author(s):  
Seulgi Moon ◽  
◽  
Bradley W. Goodfellow ◽  
J. Taylor Perron ◽  
Stephen J. Martel ◽  
...  
Keyword(s):  
Compressive Stresses

"New Donors" in Czochralski Grown Silicon Annealed at T≥ 600°C under Compressive Stress

2005 ◽  
Vol 108-109 ◽  
pp. 181-186 ◽  
Author(s):  
Valentin V. Emtsev ◽  
Boris A. Andreev ◽  
Gagik A. Oganesyan ◽  
D.I. Kryzhkov ◽  
Andrzej Misiuk ◽  
...  
Keyword(s):  
Mechanical Stress ◽  
Compressive Stress ◽  
Reference Temperature ◽  
Enhancement Effect ◽  
Shallow Acceptor ◽  
Thermal Donor ◽  
Compressive Stresses ◽  
Heat Treated ◽  
Donor Formation ◽  
New Donors

Effects of compressive stress on oxygen agglomeration processes in Czochralski grown silicon heat treated at T= 450OC, used as a reference temperature, and T= 600OC to 800OC are investigated in some detail. Compressive stresses of about P= 1 GPa lead to enhanced formation of Thermal Double Donors in materials annealed over a temperature range of T= 450OC – 600OC. It has been shown that the formation of thermal donors at T= 450OC under normal conditions and compressive stress is accompanied with loss of substitutional boron. In contrast, the concentration of the shallow acceptor states of substitutional boron in silicon annealed under stress at T≥ 600OC remains constant. An enhancement effect of thermal donor formation is gradually weakened at T≥ 700OC. The oxygen diffusivity sensitive to mechanical stress is believed to be responsible for the observed effects in heat-treated silicon.

scholarly journals BoSL FAL Pump: a small, low-cost, easily constructed, 3D-printed peristaltic pump for sampling of waters

HardwareX ◽  
2021 ◽  
pp. e00214
Author(s):  
David T. McCarthy ◽  
Baiqian Shi ◽  
Miao Wang ◽  
Stephen Catsamas
Keyword(s):  
Low Cost ◽  
Peristaltic Pump ◽  
3D Printed

scholarly journals Mechanism of Nano-Structuring Manipulation of the Crystallization Temperature of Superlattice-like [Ge8Sb92/Ge]3 Phase-Change Films

Nanomaterials ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 20
Author(s):  
Qingqian Qiu ◽  
Pengzhi Wu ◽  
Yifeng Hu ◽  
Jiwei Zhai ◽  
Tianshu Lai
Keyword(s):  
Phase Change ◽  
Crystallization Temperature ◽  
Lattice Mismatch ◽  
Stress Effect ◽  
Phonon Modes ◽  
Cycle Number ◽  
Interfacial Effects ◽  
Compressive Stresses ◽  
Crystalline Films ◽  
Change Material

Superlattice-like (SLL) phase-change film is considered to be a promising phase-change material because it provides more controllabilities for the optimization of multiple performances of phase-change films. However, the mechanism by which SLL structure affects the properties of phase-change films is not well-understood. Here, four SLL phase-change films [Ge8Sb92(15 nm)/Ge (x nm)]3 with different x are fabricated. Their behaviors of crystallization are investigated by measuring sheet resistance and coherent phonon spectroscopy, which show that the crystallization temperature (TC) of these films increases anomalously with x, rather than decreases as the interfacial effects model predicted. A new stress effect is proposed to explain the anomalous increase in TC with x. Raman spectroscopy reveals that Raman shifts of all phonon modes in SLL films deviate from their respective standard Raman shifts in stress-free crystalline films, confirming the presence of stress in SLL films. It is also shown that tensile and compressive stresses exist in Ge and Ge8Sb92 layers, respectively, which agrees with the lattice mismatch between the Ge and Ge8Sb92 constituent layers. It is also found that the stress reduces with increasing x. Such a thickness dependence of stress can be used to explain the increase in crystallization temperature of four SLL films with x according to stress-enhanced crystallization. Our results reveal a new mechanism to affect the crystallization behaviors of SLL phase-change films besides interfacial effect. Stress and interfacial effects actually coexist and compete in SLL films, which can be used to explain the reported anomalous change in crystallization temperature with the film thickness and cycle number of periods in SLL phase-change films.

scholarly journals Thermal Effects on Surface and Subsurface Modifications in Laser-Combined Deep Rolling

2021 ◽  
Vol 5 (2) ◽  
pp. 55
Author(s):  
Robert Zmich ◽  
Daniel Meyer
Keyword(s):  
Surface Layer ◽  
Residual Stresses ◽  
Thermal Loads ◽  
Deep Rolling ◽  
Mechanical Loads ◽  
Thermomechanical Process ◽  
Compressive Stresses ◽  
New Process ◽  
Negative Effect ◽  
Compressive Residual Stresses

Knowledge of the relationships between thermomechanical process loads and the resulting modifications in the surface layer enables targeted adjustments of the required surface integrity independent of the manufacturing process. In various processes with thermomechanical impact, thermal and mechanical loads act simultaneously and affect each other. Thus, the effects on the modifications are interdependent. To gain a better understanding of the interactions of the two loads, it is necessary to vary thermal and mechanical loads independently. A new process of laser-combined deep rolling can fulfil exactly this requirement. The presented findings demonstrate that thermal loads can support the generation of residual compressive stresses to a certain extent. If the thermal loads are increased further, this has a negative effect on the surface layer and the residual stresses are shifted in the direction of tension. The results show the optimum range of thermal loads to further increase the compressive residual stresses in the surface layer and allow to gain a better understanding of the interactions between thermal and mechanical loads.

scholarly journals Use of the AE Effect to Determine the Stresses State in AAC Masonry Walls under Compression

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3459
Author(s):  
Radosław Jasiński ◽  
Krzysztof Stebel ◽  
Paweł Kielan
Keyword(s):  
Ultrasonic Waves ◽  
Image Correlation ◽  
Masonry Walls ◽  
Acceptable Error ◽  
Compressive Stresses ◽  
Deformation State ◽  
Hydrostatic Stresses ◽  
Stress States ◽  
The Impact ◽  
Masonry Units

Safety and reliability of constructions operated are predicted using the known mechanical properties of materials and geometry of cross-sections, and also the known internal forces. The extensometry technique (electro-resistant tensometers, wire gauges, sensor systems) is a common method applied under laboratory conditions to determine the deformation state of a material. The construction sector rarely uses ultrasonic extensometry with the acoustoelastic (AE) method which is based on the relation between the direction of ultrasonic waves and the direction of normal stresses. It is generally used to identify stress states of machine or vehicles parts, mainly made of steel, characterized by high homogeneity and a lack of inherent internal defects. The AE effect was detected in autoclaved aerated concrete (AAC), which is usually used in masonry units. The acoustoelastic effect was used in the tests described to identify the complex stress state in masonry walls (masonry units) made of AAC. At first, the relationships were determined for mean hydrostatic stresses P and mean compressive stresses σ3 with relation to velocities of the longitudinal ultrasonic wave cp. These stresses were used to determine stresses σ3. The discrete approach was used which consists in analyzing single masonry units. Changes in velocity of longitudinal waves were identified at a test stand to control the stress states of an element tested by the digital image correlation (DIC) technique. The analyses involved density and the impact of moisture content of AAC. Then, the method was verified on nine walls subjected to axial compression and the model was validated with the FEM micromodel. It was demonstrated that mean compressive stresses σ3 and hydrostatic stresses, which were determined for the masonry using the method considered, could be determined even up to ca. 75% of failure stresses at the acceptable error level of 15%. Stresses σ1 parallel to bed joints were calculated using the known mean hydrostatic stresses and mean compressive stresses σ3.

scholarly journals Machining Ti-6Al-4V Alloy Using Nano-Cutting Fluids: Investigation and Analysis

2021 ◽  
Vol 5 (2) ◽  
pp. 42
Author(s):  
Abdelkrem Eltaggaz ◽  
Ibrahim Nouzil ◽  
Ibrahim Deiab
Keyword(s):  
Surface Finish ◽  
Minimum Quantity Lubrication ◽  
Weight Fraction ◽  
Contact Length ◽  
Al2o3 Nanoparticles ◽  
Compressive Stresses ◽  
Cutting Zone ◽  
The Impact ◽  
Cooling And Lubrication

Minimum Quantity Lubrication nanofluid (MQL-nanofluid) is a viable sustainable alternative to conventional flood cooling and provides very good cooling and lubrication in the machining of difficult to cut materials such as titanium and Inconel. The cutting action provides very difficult conditions for the coolant to access the cutting zone and the level of difficulty increases with higher cutting speeds. Furthermore, high compressive stresses, strain hardening and high chemical activity results in the formation of a ‘seizure zone’ at the tool-chip interface. In this work, the impact of MQL-nanofluid at the seizure zone and the corresponding effects on tool wear, surface finish, and power consumption during machining of Ti-6Al-4V was investigated. Aluminum Oxide (Al2O3) nanoparticles were selected to use as nano-additives at different weight fraction concentrations (0, 2, and 4 wt.%). It was observed that under pure MQL strategy there was significant material adhesion on the rake face of the tool while the adhesion was reduced in the presence of MQL-nanofluid at the tool-chip interface, thus indicating a reduction in the tool chip contact length (TCCL) and reduced seizure effect. Furthermore, the flank wear varied from 0.162 to 0.561 mm and the average surface roughness (Ra) varied from 0.512 to 2.81 µm. The results indicate that the nanoparticle concentration and the reduction in the seizure zone positively influence the tool life and quality of surface finish.

Sign in / Sign up

Export Citation Format

Share Document