scholarly journals Study of damped vibrations of a vibroacoustic interior problem with viscoelastic sandwich structure using a High Order Newton solver

2019 ◽  
Vol 462 ◽  
pp. 114947 ◽  
Author(s):  
B. Claude ◽  
L. Duigou ◽  
G. Girault ◽  
J.M. Cadou
Keyword(s):  
Sandwich Structure ◽  
High Order ◽  
Interior Problem

Static mechanical response of sandwich panels with bilinear core

2018 ◽  
Vol 22 (7) ◽  
pp. 2421-2444
Author(s):  
Guangtao Wei ◽  
Lijia Feng ◽  
Linzhi Wu
Keyword(s):  
Theoretical Model ◽  
Sandwich Structure ◽  
Sandwich Panel ◽  
Mechanical Response ◽  
Constitutive Relations ◽  
Plastic Region ◽  
Sandwich Panels ◽  
High Order ◽  
Isotropic Hardening ◽  
The Core

A new theoretical model based on the extended high order sandwich panel theory is established to predict the mechanical response of sandwich panels under static loads with the bilinear constitutive stress–strain relation in the core. The constitutive relations of normal stresses related to the longitudinal and vertical normal strains in the bilinear isotropic hardening core are first formulated. The influence of the in-plane rigidity on the elastoplastic response of sandwich structures is analyzed. An in-plane loaded sandwich structure with the bilinear core is first studied based on extended high order sandwich panel theory, and the effect of the bilinear ratio on the mechanical response is evaluated. The governing equations are derived from the principle of minimum potential energy, and a Ritz-based half-analytical method is applied to get the solutions. The plastic response is acquired by an iterative procedure along with the convergence criteria. The results reveal that the local effect can be captured when the axial rigidity of the core is considered. The bilinear characteristic of the core decreases the maximum normal stress with an increase of the average value. The equivalent plastic region extends with the increase of the bilinear ratio when the sandwich structure is loaded in plane. By comparison with open literatures and finite element results, the present theoretical model is proved to be effective and efficient.

Determination of the Burgers vector of a dislocation in a Fe-Mn alloy by weak-beam image in HVEM

1978 ◽  
Vol 36 (1) ◽  
pp. 330-331
Author(s):  
Y. Ishida ◽  
H. Ishida ◽  
K. Kohra ◽  
H. Ichinose
Keyword(s):  
High Order ◽  
Simulation Technique ◽  
The Other ◽  
Image Simulation ◽  
Diffraction Vector ◽  
Burgers Vector ◽  
Weak Beam ◽  
Beam Image ◽  
Edge Component

IntroductionA simple and accurate technique to determine the Burgers vector of a dislocation has become feasible with the advent of HVEM. The conventional image vanishing technique(1) using Bragg conditions with the diffraction vector perpendicular to the Burgers vector suffers from various drawbacks; The dislocation image appears even when the g.b = 0 criterion is satisfied, if the edge component of the dislocation is large. On the other hand, the image disappears for certain high order diffractions even when g.b ≠ 0. Furthermore, the determination of the magnitude of the Burgers vector is not easy with the criterion. Recent image simulation technique is free from the ambiguities but require too many parameters for the computation. The weak-beam “fringe counting” technique investigated in the present study is immune from the problems. Even the magnitude of the Burgers vector is determined from the number of the terminating thickness fringes at the exit of the dislocation in wedge shaped foil surfaces.

The usefulness of high index low symmetry zone axes for holz line analysis

1987 ◽  
Vol 45 ◽  
pp. 384-385
Author(s):  
C. M. Sung ◽  
D. B. Williams
Keyword(s):  
Lattice Parameter ◽  
High Order ◽  
Zone Axis ◽  
High Index ◽  
High Symmetry ◽  
Second Phases ◽  
Line Patterns ◽  
Low Symmetry ◽  
Line Analysis

Researchers have tended to use high symmetry zone axes (e.g. <111> <114>) for High Order Laue Zone (HOLZ) line analysis since Jones et al reported the origin of HOLZ lines and described some of their applications. But it is not always easy to find HOLZ lines from a specific high symmetry zone axis during microscope operation, especially from second phases on a scale of tens of nanometers. Therefore it would be very convenient if we can use HOLZ lines from low symmetry zone axes and simulate these patterns in order to measure lattice parameter changes through HOLZ line shifts. HOLZ patterns of high index low symmetry zone axes are shown in Fig. 1, which were obtained from pure Al at -186°C using a double tilt cooling holder. Their corresponding simulated HOLZ line patterns are shown along with ten other low symmetry orientations in Fig. 2. The simulations were based upon kinematical diffraction conditions.

Imaging magnetic microstructure with SEMPA

1993 ◽  
Vol 51 ◽  
pp. 1032-1033
Author(s):  
M. H. Kelley ◽  
J. Unguris ◽  
R. J. Celotta ◽  
D. T. Pierce
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Electron Microscopy ◽  
Sandwich Structure ◽  
Magnetic Coupling ◽  
Polarization Analysis ◽  
Secondary Electrons ◽  
Magnetic Microstructure ◽  
Escape Depth ◽  
Scanning Electron

By measuring the spin polarization of secondary electrons generated in a scanning electron microscope, scanning electron microscopy with polarization analysis (SEMPA) can directly image the magnitude and direction of a material’s magnetization. Because the escape depth of the secondaries is only on the order of 1 nm, SEMPA is especially well-suited for investigating the magnetization of ultra-thin films and surfaces. We have exploited this feature of SEMPA to study the magnetic microstrcture and magnetic coupling in ferromagnetic multilayers where the layers may only be a few atomic layers thick. For example, we have measured the magnetic coupling in Fe/Cr/Fe(100) and Fe/Ag/Fe(100) trilayers and have found that the coupling oscillates between ferromagnetic and antiferromagnetic as a function of the Cr or Ag spacer thickness.The SEMPA apparatus has been described in detail elsewhere. The sample consisted of a magnetic sandwich structure with a wedge-shaped interlayer as shown in Fig. 1.

Are HOLZ lines kinematic in off-zone-axis orientation?

1993 ◽  
Vol 51 ◽  
pp. 692-693
Author(s):  
J. M. Zuo ◽  
A. L. Weickenmeier ◽  
R. Holmestad ◽  
J. C. H. Spence
Keyword(s):  
Structure Determination ◽  
Standard Procedure ◽  
High Order ◽  
Zone Axis ◽  
Great Promise ◽  
Line Position ◽  
Measured Intensity ◽  
Constant Intensity ◽  
Axis Orientation ◽  
Diffraction Condition

The application of high order reflections in a weak diffraction condition off the zone axis center, including those in high order laue zones (HOLZ), holds great promise for structure determination using convergent beam electron diffraction (CBED). It is believed that in this case the intensities of high order reflections are kinematic or two-beam like. Hence, the measured intensity can be related to the structure factor amplitude. Then the standard procedure of structure determination in crystallography may be used for solving unknown structures. The dynamic effect on HOLZ line position and intensity in a strongly diffracting zone axis is well known. In a weak diffraction condition, the HOLZ line position may be approximated by the kinematic position, however, it is not clear whether this is also true for HOLZ intensities. The HOLZ lines, as they appear in CBED patterns, do show strong intensity variations along the line especially near the crossing of two lines, rather than constant intensity along the Bragg condition as predicted by kinematic or two beam theory.

Enhanced performance of supercapacitors by constructing a “mini parallel-plate capacitor” in an electrode with high dielectric constant materials

2020 ◽  
Vol 8 (32) ◽  
pp. 16661-16668
Author(s):  
Huayao Tu ◽  
Shouzhi Wang ◽  
Hehe Jiang ◽  
Zhenyan Liang ◽  
Dong Shi ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Carbon Fiber ◽  
Parallel Plate ◽  
Sandwich Structure ◽  
High Dielectric Constant ◽  
Parallel Plate Capacitor ◽  
Plate Capacitor ◽  
Fiber Metal ◽  
High Dielectric ◽  
Mini Plate

The carbon fiber/metal oxide/metal oxynitride layer sandwich structure is constructed in the electrode to form a mini-plate capacitor. High dielectric constant metal oxides act as dielectric to increase their capacitance.

Relativistic high-order harmonic generation

2003 ◽  
Vol 50 (3-4) ◽  
pp. 375-386
Author(s):  
D. B. MilosÕeviĆ ◽  
W. Becker
Keyword(s):  
Harmonic Generation ◽  
High Order ◽  
High Order Harmonic Generation ◽  
High Order Harmonic
Sign in / Sign up

Export Citation Format

Share Document