Fabricating boride layer on the titanium surface to optimize microstructure of the Ti/Al interface reaction zone

2021 ◽  
pp. 131440
Author(s):  
Zhijie Zhang ◽  
Jian Huang
2017 ◽  
Vol 724 ◽  
pp. 711-719 ◽  
Author(s):  
Rudy Guicheteau ◽  
Jean-Louis Bobet ◽  
Takamichi Miyasaki ◽  
Akira Kawasaki ◽  
Yongfeng Lu ◽  
...  

2011 ◽  
Vol 337 ◽  
pp. 598-602
Author(s):  
Quan Shan ◽  
Zu Lai Li ◽  
Ye Hua Jiang ◽  
Rong Zhou ◽  
Yu Dong Sui

In metal matrix composite, the matrix and reinforced body is different in physical and chemical properties. The transition effect of reaction zone between the matrix and reinforced body is the hot point in research aboat metal matrix composite. The steel substrat casting tungsten carbide particle surface reinforced compostie is research object in this article. The interface reaction zone is measured by EDS line scaning. The problem is solved by statistic that interference between scaning neighbour points leads to the emergence of sawtooth wave, the processed curve is beneficial to observe. The effect and effect curve of W、Mo、Ni addion is received in the interface reaction zone.


Micron ◽  
2018 ◽  
Vol 113 ◽  
pp. 91-98 ◽  
Author(s):  
Yingwei Fan ◽  
Xiaorong Zhou

Author(s):  
G. Das ◽  
R. E. Omlor

Fiber reinforced titanium alloys hold immense potential for applications in the aerospace industry. However, chemical reaction between the fibers and the titanium alloys at fabrication temperatures leads to the formation of brittle reaction products which limits their development. In the present study, coated SiC fibers have been used to evaluate the effects of surface coating on the reaction zone in the SiC/IMI829 system.IMI829 (Ti-5.5A1-3.5Sn-3.0Zr-0.3Mo-1Nb-0.3Si), a near alpha alloy, in the form of PREP powder (-35 mesh), was used a茸 the matrix. CVD grown AVCO SCS-6 SiC fibers were used as discontinuous reinforcements. These fibers of 142μm diameter contained an overlayer with high Si/C ratio on top of an amorphous carbon layer, the thickness of the coating being ∽ 1μm. SCS-6 fibers, broken into ∽ 2mm lengths, were mixed with IMI829 powder (representing < 0.1vol%) and the mixture was consolidated by HIP'ing at 871°C/0. 28GPa/4h.


2020 ◽  
Vol 9 (4) ◽  
pp. e27942662
Author(s):  
Patrícia Capellato ◽  
Cláudia Eliana Bruno Marino ◽  
Gilbert Silva ◽  
Lucas Victor Benjamim Vasconcelos ◽  
Rodrigo Perito Cardoso ◽  
...  

During the last decades, researchers have been growing the interest in surface treatment with an antimicrobial agent. Silver nanoparticles (AgNPs) are widely used in biomedical fields due to their potent antimicrobial activity. So, in this study was investigated silver particles (isles) coated on titanium surface for dental and orthopedic application. Silver particles coating process on titanium surface were performed via sputtering that is a plasma-assisted deposition technique with and titanium without treatment was applied as comparing standard. Plasma treatment parameters were optimized so that the result was not a thin film of Ag but dispersed particles of Ag on the Ti-cp surface. The alloy surfaces were investigated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). In order to investigate antibacterial potential Staphylococcus aureus and Escherichia coli have been used at Agar diffusion assay. The results were analyzed by analysis of variance (ANOVA) in order to verify significant difference antimicrobial activity between samples that have shown no difference between the surfaces studied treatments. For silver deposition scattered particles (isles) over titanium surface for a 10-minute treatment, EDS revealed by silver clusters that the particles were not properly scattered onto surface, hence, the low effectiveness in antibacterial activity.


2020 ◽  
Vol 12 (45) ◽  
pp. 63-66
Author(s):  
Halim Nagem Filho ◽  
Reinaldo Francisco Maia ◽  
Reinaldo Missaka ◽  
Nasser Hussein Fares

The osseointegration is the stable and functional union between the bone and a titanium surface. A new bone can be found on the surface of the implant about 1 week after its installation; the bone remodeling begins between 6 and 12 weeks and continues throughout life. After the implant insertion, depending on the energy of the surface, the plasma fluid immediately adheres, in close contact with the surface, promoting the adsorption of proteins and inducing the indirect interaction of the cells with the material. Macrophages are cells found in the tissues and originated from bone marrow monocytes. The M1 macrophages orchestrate the phagocytic phase in the inflammatory region and also produce inflammatory cytokines involved with the chronic inflammation and the cleaning of the wound and damaged tissues from bacteria. On the other hand, alternative-activated macrophages (M2) are activated by IL-10, the immune complex. Its main function consists on regulating negatively the inflammation through the secretion of the immunosuppressant IL-10. The M2 macrophages present involvement with the immunosuppression, besides having a low capacity for presenting antigens and high production of cytokines; these can be further divided into M2a, M2b, and M2c, based on the gene expression profile.


2020 ◽  
Vol 527 ◽  
pp. 146902 ◽  
Author(s):  
Maksim M. Kharkov ◽  
Andrey V. Kaziev ◽  
Daria V. Danilyuk ◽  
Margarita S. Kukushkina ◽  
Nikolay A. Chernyh ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document