Effect of SLM process parameters on hardness and microstructure of stainless steel 316 material

2021 ◽  
Author(s):  
Parth saxena ◽  
Hiren Gajera ◽  
Darshit Shah ◽  
Nilesh Pancholi
Keyword(s):  
Stainless Steel ◽  
Process Parameters ◽  
Stainless Steel 316

Modelling and multi-response optimization of wire electric discharge machining parameters using response surface methodology and grey–fuzzy algorithm

2015 ◽  
Vol 231 (10) ◽  
pp. 1760-1774 ◽  
Author(s):  
Bikash Choudhuri ◽  
Ruma Sen ◽  
Subrata Kumar Ghosh ◽  
Subhash Chandra Saha
Keyword(s):  
Stainless Steel ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Electric Discharge ◽  
Machining Parameters ◽  
Electric Discharge Machining ◽  
Wire Electric Discharge Machining ◽  
Grey Relational ◽  
Stainless Steel 316

Wire electric discharge machining is a non-conventional machining wherein the quality and cost of machining are influenced by the process parameters. This investigation focuses on finding the optimal level of process parameters, which is for better surface finish, material removal rate and lower wire consumption for machining stainless steel-316 using the grey–fuzzy algorithm. Grey relational technique is applied to find the grey coefficient of each performance, and fuzzy evaluates the multiple performance characteristics index according to the grey relational coefficient of each response. Response surface methodology and the analysis of variance were used for modelling and analysis of responses to predict and find the influence of machining parameters and their proportion of contribution on the individual and overall responses. The measured values from confirmation experiments were compared with the predicted values, which indicate that the proposed models can be effectively used to predict the responses in the wire electrical discharge machining of AISI stainless steel-316. It is found that servo gap set voltage is the most influential factor for this particular steel followed by pulse off time, pulse on time and wire feed rate.

scholarly journals Parameters Optimization of Auxiliary Gas Process for Double-Wire SS316L Stainless Steel Arc Additive Manufacturing

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 190
Author(s):  
Wei Wu ◽  
Jiaxiang Xue ◽  
Wei Xu ◽  
Hongyan Lin ◽  
Heqing Tang ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Additive Manufacturing ◽  
Process Parameters ◽  
Evaluation System ◽  
Gas Flow ◽  
Interactive Effect ◽  
Parameters Optimization ◽  
Heat Accumulation ◽  
Auxiliary Process ◽  
Strength And Stiffness

Serious heat accumulation limits the further efficiency and application in additive manufacturing (AM). This study accordingly proposed a double-wire SS316L stainless steel arc AM with a two-direction auxiliary gas process to research the effect of three parameters, such as auxiliary gas nozzle angle, auxiliary gas flow rate and nozzle-to-substrate distance on depositions, then based on the Box–Behnken Design response surface, a regression equation between three parameters and the total score were established to optimized parameters by an evaluation system. The results showed that samples with nozzle angle of 30° had poor morphology but good properties, and increasing gas flow or decreasing distance would enhance the airflow strength and stiffness, then strongly stir the molten pool and resist the interference. Then a diverse combination of auxiliary process parameters had different influences on the morphology and properties, and an interactive effect on the comprehensive score. Ultimately the optimal auxiliary gas process parameters were 17.4°, 25 L/min and 10.44 mm, which not only bettered the morphology, but refined the grains and improved the properties due to the stirring and cooling effect of the auxiliary gas, which provides a feasible way for quality and efficiency improvements in arc additive manufacturing.

scholarly journals Analysis of Corrosion of Hastelloy-N, Alloy X750, SS316 and SS304 in Molten Salt High-Temperature Environment

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 543
Author(s):  
Ketan Kumar Sandhi ◽  
Jerzy Szpunar
Keyword(s):  
Weight Loss ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Molten Salt ◽  
Corrosion Damage ◽  
Nickel Superalloy ◽  
Triple Junctions ◽  
Salt Corrosion ◽  
Molten Fluoride ◽  
Stainless Steel 316

Nickel superalloy Hastelloy-N, alloy X-750, stainless steel 316 (SS316), and stainless steel 304 (SS304) are among the alloys used in the construction of molten salt reactor (MSR). These alloys were analyzed for their corrosion resistance behavior in molten fluoride salt, a coolant used in MSR reactors with 46.5% LiF+ 11.5% NaF+ 42% KF. The corrosion tests were run at 700 °C for 100 h under the Ar cover gas. After corrosion, significant weight loss was observed in the alloy X750. Weight loss registered in SS316 and SS304 was also high. However, Hastelloy-N gained weight after exposure to molten salt corrosion. This could be attributed to electrochemical plating of corrosion products from other alloys on Hastelloy-N surface. SEM–energy-dispersive X-ray spectroscopy (EDXS) scans of cross-section of alloys revealed maximum corrosion damage to the depth of 250 µm in X750, in contrast to only 20 µm on Hastelloy-N. XPS wide survey scans revealed the presence of Fe, Cr, and Ni elements on the surface of all corroded alloys. In addition, Cr clusters were formed at the triple junctions of grains, as confirmed by SEM–EBSD (Electron Back Scattered Diffraction) analysis. The order of corrosion resistance in FLiNaK environment was X750 < SS316 < SS304 < Hastelloy-N.

scholarly journals Analysis of the Process Parameter Influence in Laser Cladding of 316L Stainless Steel

2018 ◽  
Vol 2 (3) ◽  
pp. 55 ◽  
Author(s):  
Piera Alvarez ◽  
M. Montealegre ◽  
Jose Pulido-Jiménez ◽  
Jon Arrizubieta
Keyword(s):  
Stainless Steel ◽  
Laser Cladding ◽  
Process Parameters ◽  
Cross Sections ◽  
316L Stainless Steel ◽  
Deposition Process ◽  
Process Parameter ◽  
Optimum Process ◽  
Processing Times ◽  
Manufacturing Technologies

Laser Cladding is one of the leading processes within Additive Manufacturing technologies, which has concentrated a considerable amount of effort on its development. In regard to the latter, the current study aims to summarize the influence of the most relevant process parameters in the laser cladding processing of single and compound volumes (solid forms) made from AISI 316L stainless steel powders and using a coaxial nozzle for their deposition. Process speed, applied laser power and powder flow are considered to be the main variables affecting the laser cladding in single clads, whereas overlap percentage and overlapping strategy also become relevant when dealing with multiple clads. By setting appropriate values for each process parameter, the main goal of this paper is to develop a processing window in which a good metallurgical bond between the delivered powder and the substrate is obtained, trying simultaneously to maintain processing times at their lowest value possible. Conventional metallography techniques were performed on the cross sections of the laser tracks to measure the effective dimensions of clads, height and width, as well as the resulting dilution value. Besides the influence of the overlap between contiguous clads and layers, physical defects such as porosity and cracks were also evaluated. Optimum process parameters to maximize productivity were defined as 13 mm/s, 2500 W, 30% of overlap and a 25 g/min powder feed rate.

Sign in / Sign up

Export Citation Format

Share Document