Stochastic homogenization of random elastic multi-phase composites and size quantification of representative volume element

2009 ◽  
Vol 41 (2) ◽  
pp. 174-186 ◽  
Author(s):  
X. Frank Xu ◽  
Xi Chen
Keyword(s):  
Representative Volume Element ◽  
Volume Element ◽  
Stochastic Homogenization ◽  
Representative Volume ◽  
Multi Phase

scholarly journals Effect of the 3rd Dimension within the Representative Volume Element (RVE) on Damage Initiation and Propagation during Full-Phase Numerical Simulations of Single and Multi-Phase Steels

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 42
Author(s):  
Faisal Qayyum ◽  
Muhammad Umar ◽  
Sergey Guk ◽  
Matthias Schmidtchen ◽  
Rudolf Kawalla ◽  
...  
Keyword(s):  
Numerical Simulations ◽  
Representative Volume Element ◽  
Volume Element ◽  
Ductile Damage ◽  
Model Parameters ◽  
Damage Initiation ◽  
Representative Volume ◽  
Multi Phase ◽  
Local Results ◽  
Global And Local

In this research, the effect of 2D and 3D Representative Volume Element (RVE) on the ductile damage behavior in single-phase (only ferrite) and dual-phase (ferrite and martensite) steels is analyzed. Physical and fitting parameters of the constitutive model for bcc-ferrite and bcc-martensite phases are adapted from the already published work. Crystal plasticity (CP) based numerical simulations without damage consideration are run and, later, ductile damage criteria for the ferrite phase is defined for all cases. The results of the non-damage (-nD-) and damage (-D-) simulations are compared to analyze the global and local differences of evolving stresses and strains. It is observed that for the same model parameters defined in all cases, damage initiation occurs at the overall higher global strain in the case of 3D compared to 2D. Based on statistical data analysis, a systematic comparison of local results is carried out to conclude that the 3D RVEs provide better quantitative and qualitative results and should be considered for such full phase simulations. Whereas 2D RVEs are simple to analyze and provide appropriate qualitative information about the damage initiation sites.

scholarly journals Representative volume element based micromechanical modelling of rod shaped glass filled epoxy composites

2021 ◽  
Vol 3 (2) ◽  
Author(s):  
Aanchna Sharma ◽  
Yashwant Munde ◽  
Vinod Kushvaha
Keyword(s):  
Representative Volume Element ◽  
Poisson’S Ratio ◽  
Volume Fraction ◽  
Tensile Modulus ◽  
Volume Element ◽  
Poisson's Ratio ◽  
Epoxy Composites ◽  
Micromechanical Modeling ◽  
Representative Volume ◽  
Shaped Glass

AbstractIn this study, Representative Volume Element based micromechanical modeling technique has been implemented to assess the mechanical properties of glass filled epoxy composites. Rod shaped glass fillers having an aspect ratio of 80 were used for preparing the epoxy composite. The three-dimensional unit cell model of representative volume element was prepared with finite element analysis tool ANSYS 19 using the periodic square and hexagonal array with an assumption that there is a perfect bonding between the filler and the epoxy matrix. Results revealed that the tensile modulus increases and Poisson’s ratio decreases with increase in the volume fraction of the filler. To study the effect of filler volume fraction, the pulse echo techniques were used to experimentally measure the tensile modulus and Poisson’s ratio for 5% to 15% volume fraction of the filler. A good agreement was found between the RVE based predicted values and the experimental results.

Localization simulation of forming-induced residual stresses of composite using prescribed boundary

2021 ◽  
pp. 073168442094118
Author(s):  
Qi Wu ◽  
Hongzhou Zhai ◽  
Nobuhiro Yoshikawa ◽  
Tomotaka Ogasawara ◽  
Naoki Morita
Keyword(s):  
Residual Stresses ◽  
Representative Volume Element ◽  
Computational Cost ◽  
Volume Element ◽  
Thermoplastic Composite ◽  
Structural Deformation ◽  
Element Analysis ◽  
Micro Scale ◽  
Representative Volume ◽  
Localization Approach

A novel localization approach that seamlessly bridges the macro- and micro-scale models is proposed and used to model the forming-induced residual stresses within a representative volume element of a fiber reinforced composite. The approach uses a prescribed boundary that is theoretically deduced by integrating the asymptotic expansion of a composite and the equal strain transfer, thus rendering the simulation setting to be easier than conventional approaches. When the localization approach is used for the finite element analysis, the temperature and residual stresses within an ideal cubic representative volume element are precisely simulated, given a sandwiched thermoplastic composite is formed under one-side cooling condition. The simulation results, after being validated, show that the temperature gradient has an impact on the local residual stresses, especially on the in-plane normal stress transverse to the fiber, and consequently, influences the structural deformation. This newly designed localization approach demonstrates the advantages of enhanced precision and reduced computational cost owing to the fast modeling of the finely meshed representative volume element. This is beneficial for a detailed understanding of the actual residual stresses at the micro-scale.

Sign in / Sign up

Export Citation Format

Share Document