Large-eddy simulation of separated flow over a swept wing with approximate near-wall modelling

2007 ◽  
Vol 111 (1125) ◽  
pp. 689-697 ◽  
Author(s):  
N. Li ◽  
M. A. Leschziner
Keyword(s):  
Vortex Breakdown ◽  
Separated Flow ◽  
Leading Edge ◽  
Suction Side ◽  
Wall Layer ◽  
Swept Wing ◽  
Validation Data ◽  
Eddy Simulation ◽  
Eddy Viscosity Model ◽  
Near Wall

Abstract The paper investigates, by means of a simulation methodology, the flow separating from a 40 degrees backward-swept wing at 9 degrees incidence and Reynolds number of 210,000, based on the wing-root chord length. The Simulation corresponds to LDA, PIV and suction-side-topology measurements for the same geometry, conducted by other investigators specifically to provide validation data. The finest block-structured mesh contains 23·6 million nodes and is organised in 256 blocks to maximise mesh quality and facilitate parallel solution on multi-processor machines. The near-wall layer is resolved, to a thickness of about y + = 20, by means of parabolised URANS equations that include an algebraic eddy-viscosity model and from which the wall-shear stress is extracted to provide an unsteady boundary condition for the simulation. The numerical solution is in good agreement with the experimental behaviour over the 50-70% inboard portion of the span, but the simulation fails to resolve some complex features close to the wing tip, due to a premature leading-edge vortex breakdown and loss in vortex coherence. The comparisons and their discussion provide useful insight into various physical characteristics of this complex separated wing flow.

Simulating flow separation from continuous surfaces: routes to overcoming the Reynolds number barrier

2009 ◽  
Vol 367 (1899) ◽  
pp. 2885-2903 ◽  
Author(s):  
Michael Leschziner ◽  
Ning Li ◽  
Fabrizio Tessicini
Keyword(s):  
Reynolds Number ◽  
Turbulent Flows ◽  
Major Elements ◽  
Wall Layer ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rans Models ◽  
High Reynolds ◽  
Near Wall

This paper provides a discussion of several aspects of the construction of approaches that combine statistical (Reynolds-averaged Navier–Stokes, RANS) models with large eddy simulation (LES), with the objective of making LES an economically viable method for predicting complex, high Reynolds number turbulent flows. The first part provides a review of alternative approaches, highlighting their rationale and major elements. Next, two particular methods are introduced in greater detail: one based on coupling near-wall RANS models to the outer LES domain on a single contiguous mesh, and the other involving the application of the RANS and LES procedures on separate zones, the former confined to a thin near-wall layer. Examples for their performance are included for channel flow and, in the case of the zonal strategy, for three separated flows. Finally, a discussion of prospects is given, as viewed from the writer's perspective.

Numerical Investigation of Intermittent Corner Separation in a Linear Compressor Cascade

2016 ◽  
Author(s):  
Wei Ma ◽  
Feng Gao ◽  
Xavier Ottavy ◽  
Lipeng Lu ◽  
A. J. Wang
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Leading Edge ◽  
Suction Side ◽  
Detached Eddy Simulation ◽  
Compressor Cascade ◽  
Linear Compressor ◽  
Corner Separation ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

Recently bimodal phenomenon in corner separation has been found by Ma et al. (Experiments in Fluids, 2013, doi:10.1007/s00348-013-1546-y). Through detailed and accurate experimental results of the velocity flow field in a linear compressor cascade, they discovered two aperiodic modes exist in the corner separation of the compressor cascade. This phenomenon reflects the flow in corner separation is high intermittent, and large-scale coherent structures corresponding to two modes exist in the flow field of corner separation. However the generation mechanism of the bimodal phenomenon in corner separation is still unclear and thus needs to be studied further. In order to obtain instantaneous flow field with different unsteadiness and thus to analyse the mechanisms of bimodal phenomenon in corner separation, in this paper detached-eddy simulation (DES) is used to simulate the flow field in the linear compressor cascade where bimodal phenomenon has been found in previous experiment. DES in this paper successfully captures the bimodal phenomenon in the linear compressor cascade found in experiment, including the locations of bimodal points and the development of bimodal points along a line that normal to the blade suction side. We infer that the bimodal phenomenon in the corner separation is induced by the strong interaction between the following two facts. The first is the unsteady upstream flow nearby the leading edge whose angle and magnitude fluctuate simultaneously and significantly. The second is the high unsteady separation in the corner region.

Improved Prediction of Losses with Large Eddy Simulation in a Low- Pressure Turbine

2021 ◽  
pp. 1-38
Author(s):  
Kenji Miki ◽  
Ali Ameri
Keyword(s):  
Experimental Data ◽  
Gas Turbines ◽  
Suction Side ◽  
Transition Process ◽  
Low Pressure ◽  
Validation Data ◽  
Eddy Simulation ◽  
Power Turbine ◽  
Large Eddy ◽  
Characteristic Features

Abstract There is a need to improve predictions of losses resulting from large eddy simulations (LES) of low-pressure turbines (LPT) in gas turbines. This may be done by assessing the accuracy of predictions against validation data and understanding the source of any inaccuracies. LES is a promising approach for capturing the laminar/turbulent transition process in a LPT. In previous studies, the authors utilized LES to model the flow field over a Variable Speed Power Turbine (VSPT) blade and successfully captured characteristic features of separation/reattachment and transition on the suction side at both the cruise (positive incidence) and take-off conditions (negative incidence) and as well, simulated the effect of freestream turbulence (FST) on those phenomena. The predicted pressure loading profiles agreed well with the experimental data for both a high and a low FST case at a Reynolds number of Reex = 220,000. In this paper, we present wake profiles resulting from computations for a range of FST values. Although the predicted wake profiles for the lowest FST case (Tu = 0.5%) matched the experimental data, at higher FST (Tu = 10-15%,) the wake was wider than the experimentally measured wake and for both cases were displaced laterally when compared to the experimental measurements. In our investigation of the causes of the said discrepancies we have identified important effects which could strongly influence the predicted wake profile. Predicted losses were improved by assuring the validity of the flow solution.

Analysis of Vortical Flow Field in a Propeller Fan by LDV Measurements and LES—Part II: Unsteady Nature of Vortical Flow Structures Due to Tip Vortex Breakdown

2001 ◽  
Vol 123 (4) ◽  
pp. 755-761 ◽  
Author(s):  
Choon-Man Jang ◽  
Masato Furukawa ◽  
Masahiro Inoue
Keyword(s):  
Vortex Breakdown ◽  
Pressure Fluctuations ◽  
Leading Edge ◽  
Vortex Structures ◽  
Tip Vortex ◽  
Vortical Flow ◽  
Small Scale ◽  
Pressure Surface ◽  
Eddy Simulation ◽  
Cyclic Movements

The unsteady nature of vortex structures has been investigated by a large eddy simulation (LES) in a propeller fan with a shroud covering only the rear region of its rotor tip. The simulation shows that the tip vortex plays a major role in the structure and unsteady behavior of the vortical flow in the propeller fan. The spiral-type breakdown of the tip vortex occurs near the midpitch, leading to significant changes in the nature of the tip vortex. The breakdown gives rise to large and cyclic movements of the tip vortex, so that the vortex impinges cyclically on the pressure surface of the adjacent blade. The movements of the tip vortex cause the leading edge separation vortex to oscillate in a cycle, but on a small scale. The movements of the vortex structures induce high-pressure fluctuations on the rotor blade and in the blade passage.

An Integrated Particle-Tracking Impact/Adhesion Model for the Prediction of Fouling in a Subsonic Compressor

2012 ◽  
Vol 134 (9) ◽  
Author(s):  
D. Borello ◽  
F. Rispoli ◽  
P. Venturini
Keyword(s):  
Leading Edge ◽  
Suction Side ◽  
Navier Stokes ◽  
Compressor Cascade ◽  
Deposit Formation ◽  
Stagnation Region ◽  
Vortical Structures ◽  
Tip Leakage ◽  
Eddy Simulation ◽  
Linear Compressor Cascade

The present paper reports on the analysis of the motion of adhesive particles and deposit formation in a 3D linear compressor cascade in order to investigate the fouling in turbomachinery flows. The unsteady flow field is provided by a prior hybrid large-eddy simulation (LES)/Reynolds-averaged Navier-Stokes (RANS) computation. The particles are individually tracked and the deposit formation is evaluated on the basis of the well-established Thornton and Ning model. Although the study is limited to three regions of the blade, where the most relevant turbulent phenomena occurs, the prediction of fouling shows good agreement with real situations. Deposits form near the casing and the hub, in the zones where there are strong vortical structures originated by the tip leakage and hub vortices. On the blade, the deposit analysis is focused on three main regions: (a) along the stagnation region on the leading edge; (b) on the suction side, where the particles are conveyed by the hub vortex towards blade surfaces; and (c) on the pressure side, where a clean zone forms between leading edge and the blade surface, as can be seen in real compressors.

On the Vortex Breakdown Phenomenon in High Angle of Attack Flows Over Delta Wing Geometries

2014 ◽  
Author(s):  
Eric D. Robertson ◽  
Varun Chitta ◽  
D. Keith Walters ◽  
Shanti Bhushan
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
High Angle ◽  
High Angle Of Attack ◽  
Eddy Simulation ◽  
Wing Model

Using computational methods, an investigation was performed on the physical mechanisms leading to vortex breakdown in high angle of attack flows over delta wing geometries. For this purpose, the Second International Vortex Flow Experiment (VFE-2) 65° sweep delta wing model was studied at a root chord Reynolds number (Recr) of 6 × 106 at various angles of attack. The open-source computational fluid dynamics (CFD) solver OpenFOAM was used in parallel with the commercial CFD solver ANSYS® FLUENT. For breadth, a variety of classic closure models were applied, including unsteady Reynolds-averaged Navier-Stokes (URANS) and detached eddy simulation (DES). Results for all cases are analyzed and flow features are identified and discussed. The results show the inception of a pair of leading edge vortices originating at the apex for all models used, and a region of steady vortical structures downstream in the URANS results. However, DES results show regions of massively separated helical flow which manifests after vortex breakdown. Analysis of turbulence quantities in the breakdown region gives further insight into the mechanisms leading to such phenomena.

Turbulence-Chemistry Interactions in Spray Combustion

2002 ◽  
Author(s):  
Vaidyanathan Sankaran ◽  
Suresh Menon
Keyword(s):  
Heat Release ◽  
Recirculation Zone ◽  
Vortex Breakdown ◽  
Separated Flow ◽  
Spray Combustion ◽  
Mixing Efficiency ◽  
Eddy Simulation ◽  
Swirl Intensity ◽  
Air Mixing ◽  
Combustion Processes

A prediction methodology based on Large-Eddy Simulation (LES) has been used to study turbulence-chemistry interactions in spray combustion. The unsteady interactions between spray dispersion and vaporization, fuel-air mixing and heat release has been investigated using a Stochastic Separated Flow model for spray within the LES formulation. The effects of swirl intensity and heat release are investigated here. Results show that the central toroidal recirculation zone (CTRZ), which is a manifestation of the vortex breakdown process, occurs only under high swirl conditions. Under non-reacting condition, droplets tend to concentrate in regions of low vorticity and increase in swirl increases the dispersion of the droplets. Mixing efficiency is enhanced and the size of the corner recirculation zone is decreased with increase in swirl. Increase in swirl also enhances the combustion processes for cases with heat release.

scholarly journals Investigation and Improvement of Stall Characteristic of High-Lift Configuration without Slats

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Zhao Yang ◽  
Jie Li ◽  
Jing Jin ◽  
Heng Zhang ◽  
Youxu Jiang
Keyword(s):  
Evaluation Method ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Characteristics ◽  
Angle Distribution ◽  
Detached Eddy Simulation ◽  
High Lift ◽  
Eddy Simulation ◽  
Business Jet ◽  
Delayed Detached Eddy Simulation

In order to simplify the manufacturing process or because of the limitation of the propulsion system, business jet, small civil airplane, and turboprop aircraft are always designed without leading-edge slats, which poses a great challenge to the flight safety during takeoff and landing. Focusing on the low-speed stall and poststall conditions, we investigated the aerodynamic characteristics and flow mechanism of high-lift configuration without slats using an improved delayed detached eddy simulation (IDDES) model which is validated by numerical simulations of the Common Research Model (CRM). Based on the analysis of the calculated results, conclusion can be made that the stall behavior of the configurations is directly related to the onset and evaluation of flow separation on the suction side. And through further research, an efficient evaluation method that is capable of qualitatively predicting the stall performance of two-element high-lift configuration by stall angle distribution of wing sections is proposed. By using the evaluation method, together with design rules summarized from the present study, high-lift configuration with mild-stall characteristic can be obtained in the preliminary stage of design.

Computational Study of Flow Characteristics of Thick and Thin Airfoil With Implicit Large-Eddy Simulation at Low Reynolds Number

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
Kozo Fujii
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Laminar Separation Bubble ◽  
Laminar Separation ◽  
Eddy Simulation ◽  
Naca0012 Airfoil ◽  
Large Eddy ◽  
Implicit Large Eddy Simulation

The flow fields around NACA0012 and NACA0002 at Reynolds number of 23,000, and their aerodynamic characteristics are analyzed. Computations are conducted with implicit large-eddy simulation solver and Reynolds-averaged-Navier-Stokes solver. Around this Reynolds number, the flow over an airfoil separates, transits and reattaches, resulting in generation of a laminar separation bubble at angle of attack in the range of certain degrees. Over a NACA0012 airfoil a separation point moves toward its leading edge with increasing angle of attack, and a separated flow may transit to create a short bubble. On the other hand, over a NACA0002 airfoil a separation point is kept at its leading edge, and a separated flow may transit to create a long bubble. Moreover, there appears nonlinearity in lift curve for NACA0012 airfoil, but does not appear in that for NACA0002 in spite of existence of a laminar separation bubble.

Sign in / Sign up

Export Citation Format

Share Document