Observations oh Nucleation and Growth of Voids in Nickel

1970 ◽  
Vol 28 ◽  
pp. 414-415
Author(s):  
J. L. Brimhall ◽  
H. E. Kissinger ◽  
B. Mastel
Keyword(s):  
High Purity ◽  
Growth Stage ◽  
Elevated Temperatures ◽  
Early Growth ◽  
Nucleation And Growth ◽  
Pure Nickel ◽  
Different Temperatures ◽  
Total Fluence ◽  
Neutron Exposure ◽  
Growth Of Voids

Some information on the size and density of voids that develop in several high purity metals and alloys during irradiation with neutrons at elevated temperatures has been reported as a function of irradiation parameters. An area of particular interest is the nucleation and early growth stage of voids. It is the purpose of this paper to describe the microstructure in high purity nickel after irradiation to a very low but constant neutron exposure at three different temperatures.Annealed specimens of 99-997% pure nickel in the form of foils 75μ thick were irradiated in a capsule to a total fluence of 2.2 × 1019 n/cm2 (E > 1.0 MeV). The capsule consisted of three temperature zones maintained by heaters and monitored by thermocouples at 350, 400, and 450°C, respectively. The temperature was automatically dropped to 60°C while the reactor was down.

Nucleation and Growth of Voids in Silicon

1997 ◽  
Vol 490 ◽  
Author(s):  
P. S. Plekhanov ◽  
U. M. Gösele ◽  
T. Y. Tan
Keyword(s):  
Void Growth ◽  
Homogeneous Nucleation ◽  
Nucleation And Growth ◽  
Vacancy Formation ◽  
Limited Time ◽  
Dislocation Loops ◽  
Nucleation Barrier ◽  
Different Temperatures ◽  
Type Dislocation ◽  
Growth Of Voids

ABSTRACTNucleation of voids and vacancy-type dislocation loops in Si under vacancy supersaturation conditions has been considered. Based upon nucleation barrier calculations, it has been found that voids can be nucleated, but not dislocation loops. The homogeneous nucleation rate of voids has been calculated for different temperatures by assuming different enthalpy values of Si vacancy formation. The process of void growth due to precipitation of vacancies has been numerically simulated. Comparing results of the nucleation and the growth modeling and taking into account the competition between the two processes, the limited time available, and the crystal cooling rate after growth, it has been shown that homogeneous nucleation of voids to experimentally observed densities and void growth to observed sizes is possible if enthalpy of Si vacancy formation is within the range of 2.9 to 3.6 eV with the nucleation temperature in the range of 980–1080 °C.

Spherulite Structures in a Melt Spun Fe-Ni Austenitic Steel

1985 ◽  
Vol 43 ◽  
pp. 52-53
Author(s):  
G. M. Michal ◽  
T. K. Glasgow ◽  
T. J. Moore
Keyword(s):  
Austenitic Steel ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Large Range ◽  
Amorphous Structure ◽  
Nucleation And Growth ◽  
Ni Alloys ◽  
Melt Spun ◽  
Crystal Fibers ◽  
Rapidly Solidified

Large additions of B to Fe-Ni alloys can lead to the formation of an amorphous structure, if the alloy is rapidly cooled from the liquid state to room temperature. Isothermal aging of such structures at elevated temperatures causes crystallization to occur. Commonly such crystallization pro ceeds by the nucleation and growth of spherulites which are spherical crystalline bodies of radiating crystal fibers. Spherulite features were found in the present study in a rapidly solidified alloy that was fully crysstalline as-cast. This alloy was part of a program to develop an austenitic steel for elevated temperature applications by strengthening it with TiB2. The alloy contained a relatively large percentage of B, not to induce an amorphous structure, but only as a consequence of trying to obtain a large volume fracture of TiB2 in the completely processed alloy. The observation of spherulitic features in this alloy is described herein. Utilization of the large range of useful magnifications obtainable in a modern TEM, when a suitably thinned foil is available, was a key element in this analysis.

Effect Of Elevated Temperatures On Complete Concrete Deformation Diagrams

2019 ◽  
pp. 9-14
Keyword(s):  
Experimental Data ◽  
Elastic Modulus ◽  
Elevated Temperatures ◽  
Peak Load ◽  
Relative Deformation ◽  
Deformation Characteristics ◽  
Compression Tests ◽  
Strain Behavior ◽  
Different Temperatures ◽  
Deformation Diagrams

The analysis of the previous results of the study on concrete stress-strain behavior at elevated temperatures has been carried out. Based on the analysis, the main reasons for strength retrogression and elastic modulus reduction of concrete have been identified. Despite a significant amount of research in this area, there is a large spread in experimental data received, both as a result of compression and tension. In addition, the deformation characteristics of concrete are insufficiently studied: the coefficient of transverse deformation, the limiting relative compression deformation corresponding to the peak load and the almost complete absence of studies of complete deformation diagrams at elevated temperatures. The two testing chambers provided creating the necessary temperature conditions for conducting studies under bending compression and tension have been developed. On the basis of the obtained experimental data of physical and mechanical characteristics of concrete at different temperatures under conditions of axial compression and tensile bending, conclusions about the nature of changes in strength and deformation characteristics have been drawn. Compression tests conducted following the method of concrete deformation complete curves provided obtaining diagrams not only at normal temperature, but also at elevated temperature. Based on the experimental results, dependences of changes in prism strength and elastic modulus as well as an equation for determining the relative deformation and stresses at elevated temperatures at all stages of concrete deterioration have been suggested.

Tensile Properties of Low Nickel Austenitic Stainless Steel at Elevated Temperatures

2012 ◽  
Vol 159 ◽  
pp. 346-350
Author(s):  
Shu Min Liu ◽  
Jian Bin Zhang
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Elevated Temperatures ◽  
Peak Stress ◽  
Temperature Curve ◽  
Delta Ferrite ◽  
Cross Sectional ◽  
Different Temperatures ◽  
Increasing Temperature ◽  
Reduction Percentage

The elevated temperature short-time tensile test with the sample of casting low nickel stainless steel was conducted on SHIMADZU AG-10 at ten temperatures 300, 500, 600, 700, 800, 950, 1000, 1050, 1100, and 1250°C, respectively. The stress-strain curves with the thermal deformation at the different temperatures, the peak stress intensity-temperature curve, and the reduction percentage of cross sectional area-temperature curve were obtained. Metallographic test samples were prepared and the morphology of deforming zone was observed by optical microscopy. The experimental results show that the tensile strength of the test samples decreases with increasing temperature. From 300 to 800°C, the work harding occurred and the tensile strength increases with increasing strain. The work softening occurred and the tensile strength decreases with increasing strain at temperatures of 800 to 1250°C. The minimum value of reduction percentage was measured at 800 °C. The austenite and delta-ferrite are the main phase in the tested samples. When the tensile temperatures are increased to 1200°C, the delta-ferrite became thinner and broke down to be spheroidized.

Nucleation and growth of voids by radiation

1980 ◽  
Vol 95 (1-2) ◽  
pp. 44-45 ◽  
Author(s):  
R.M. Mayer ◽  
L.M. Brown ◽  
U. Gösele
Keyword(s):  
Nucleation And Growth ◽  
Growth Of Voids

Mechanical Property and Oxidation Behavior of LPS-SiC Materials

2006 ◽  
Vol 321-323 ◽  
pp. 913-916
Author(s):  
Sang Ll Lee ◽  
Yun Seok Shin ◽  
Jin Kyung Lee ◽  
Jong Baek Lee ◽  
Jun Young Park
Keyword(s):  
Mechanical Property ◽  
Fracture Toughness ◽  
Oxidation Behavior ◽  
Elevated Temperatures ◽  
Indentation Test ◽  
Bending Test ◽  
Secondary Phases ◽  
Three Point Bending ◽  
Different Temperatures

The microstructure and the mechanical property of liquid phase sintered (LPS) SiC materials with oxide secondary phases have been investigated. The strength variation of LPS-SiC materials exposed at the elevated temperatures has been also examined. LPS-SiC materials were sintered at the different temperatures using two types of Al2O3/Y2O3 compositional ratio. The characterization of LPS-SiC materials was investigated by means of SEM with EDS, three point bending test and indentation test. The LPS-SiC material with a density of about 3.2 Mg/m3 represented a flexural strength of about 800 MPa and a fracture toughness of about 9.0 MPa⋅√m.

Sign in / Sign up

Export Citation Format

Share Document