scholarly journals Effect of V2O5 B-site substitution on the microstructure, Raman spectrum, and dielectric properties of SrBi2Ta2O9 ceramics

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Chia-Ching Wu ◽  
Cheng-Fu Yang
Keyword(s):  
Raman Spectrum ◽  
Dielectric Properties ◽  
Solid State Reaction Method ◽  
Layered Perovskite ◽  
Scanning Electron Micrographs ◽  
X Ray Diffraction ◽  
Strontium Bismuth Tantalate ◽  
Reaction Method ◽  
X Ray ◽  
Ferroelectric Characteristic

Abstract Strontium bismuth tantalate vanadate [SrBi2(Ta2−xVx)O9, SBTV] ceramics, which are bismuth-layered perovskite ferroelectrics, were synthesized through the solid-state reaction method. The effects of different sintering temperatures and V2O5 contents on the structure of the microstructure, Raman spectrum, and dielectric properties of the SBTV ceramics were investigated. As sintered at high temperature (980–1040 °C) and different V2O5 contents (x = 0.1 − x = 0.4), only disk-like grains of the SBTV ceramics were observed in the scanning electron micrographs. Preferential orientation of the crystals of the SBTV ceramics was confirmed through X-ray diffraction studies. The higher dielectric constant and Curie temperature of the SBTV ceramics compared with those of strontium bismuth tantalite (SrBi2Ta2O9, SBT) ceramics are ascribe to the partial replace of Ta5+ ions by V5+ ions in the B sites. The Curie–Weiss law and the modified Curie–Weiss law were used to discuss the normal-type or relaxor-type ferroelectric characteristic of the SBTV ceramics. The Ta5+ ion replaced by V5+ ion site in SBT ceramics to form SBTV ceramics exerted a pronounced effect on the BO6 mode, as demonstrated by Raman spectrum results.

Structural and Dielectric Properties of Na0.5Bi0.5TiO3 Ferroelectric Ceramics

2012 ◽  
Vol 585 ◽  
pp. 219-223
Author(s):  
Rekha Kumari ◽  
N. Ahlawat ◽  
Ashish Agarwal ◽  
M. Sindhu ◽  
N.N. Ahlawat
Keyword(s):  
Dielectric Properties ◽  
Solid State Reaction Method ◽  
Wide Frequency Range ◽  
Ferroelectric Ceramics ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
Reaction Method ◽  
X Ray ◽  
Different Temperatures

Na0.5Bi0.5TiO3 (NBT) ceramics were synthesized by conventional solid state reaction method. Structural and dielectric properties of these ceramics were investigated. Crystalline phase of sintered ceramics was investigated by X-ray diffraction (XRD). The Rietveld refinement of powder X-ray diffraction revealed that the prepared ceramics exhibit the rhombohedral space group R3c. Dielectric properties of Na0.5Bi0. analyzer.5TiO3 (NBT) ceramics were studied at different temperatures in a wide frequency range using impedance

Effect of Li2CO3-V2O5 on the Sintering and Microwave Dielectric Properties of 0.6Mg4Nb2O9-0.4SrTiO3 Composite Ceramics

2010 ◽  
Vol 663-665 ◽  
pp. 608-611
Author(s):  
Cui Jin Pei ◽  
Guo Guang Yao ◽  
Xiu Lao Tian ◽  
Hong Ma
Keyword(s):  
Dielectric Properties ◽  
Sintering Temperature ◽  
Microwave Dielectric Properties ◽  
Solid State Reaction Method ◽  
Composite Ceramics ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Microwave Dielectric ◽  
Co Doped

The effects of Li2CO3-V2O5 (LV) co-doped on the sinterability, phase compositions and microwave dielectric properties of 0.6Mg4Nb2O9-0.4SrTiO3 composite ceramics have been investigated. All specimens were prepared by solid-state reaction method and sintered at 1050-1200oC for 5h. With an amount LV addition, the densification sintering temperature is significantly lowed from 1300oC to 1175oC. The non-stoichiometric compounds Sr(NbTi)O3+δ and Mg4(Nb1-xTix)2O9-δ were confirmed by X-ray diffraction and energy dispersive X-ray analysis. For the specimen with 1.5 wt% LV addition sintered at 1175oC for 5 h exhibited dielectric properties: εr=20.1, Q•f=10 240 GHz, τf =0.15 ppm/oC.

Effect of Annealing on the Structure and Dielectric Properties in PZT-PCoN Ceramics

2008 ◽  
Vol 55-57 ◽  
pp. 49-52
Author(s):  
Naratip Vittayakorn ◽  
N. Chaiyo ◽  
R. Muanghlua ◽  
A. Ruangphanit ◽  
Wanwilai C. Vittayakorn
Keyword(s):  
Solid Solution ◽  
Dielectric Properties ◽  
Solid State Reaction Method ◽  
Relaxor Ferroelectric ◽  
Dielectric Constants ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Maximum Dielectric Constant ◽  
Diffraction Patterns

he solid solution between the normal ferroelectric Pb(Zr1/2Ti1/2)O3 (PZT) and relaxor ferroelectric Pb(Co1/3Nb2/3)O3 (PCoN) was synthesized by the solid state reaction method. Sintered PZT-PCoN ceramics were annealed at temperatures ranging from 850 to 1,100°C for 4 h. X-ray diffraction patterns revealed changes of crystalline structure after annealing, which could be correlated to the accompanied changes in dielectric properties. Furthermore, significant improvements in the dielectric responses were observed in this system. After annealing, a huge increase of up to 200% occurred in the dielectric constants, especially near the temperature of maximum dielectric constant.

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

scholarly journals Structure and electric properties of cerium substituted SrBi1.8Ce0.2Nb2O9 and SrBi1.8Ce0.2Ta2O9 ceramics

2016 ◽  
Vol 10 (3) ◽  
pp. 183-188 ◽  
Author(s):  
Mohamed Afqir ◽  
Amina Tachafine ◽  
Didier Fasquelle ◽  
Mohamed Elaatmani ◽  
Jean-Claude Carru ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Solid State ◽  
Room Temperature ◽  
Single Phase ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Lcr Meter ◽  
Curie Temperature Tc

SrBi1.8Ce0.2Nb2O9 (SBCN) and SrBi1.8Ce0.2Ta2O9 (SBCT) powders were prepared via solid-state reaction method. X-ray diffraction analysis reveals that the SBCN and SBCT powders have the single phase orthorhom-bic Aurivillius structure at room temperature. The contribution of Raman scattering and FTIR spectroscopy of these samples were relatively smooth and resemble each other. The calcined powders were uniaxially pressed and sintered at 1250?C for 8 h to obtaine dense ceramics. Dielectric constant, loss tangent and AC conductivity of the sintered Ce-doped SrBi2Nb2O9 and SrBi2Ta2O9 ceramics were measured by LCR meter. The Ce-doped SBN (SBCN) ceramics have a higher Curie temperature (TC) and dielectric constant at TC (380?C and ?? ~3510) compared to the Ce-doped SBT (SBCT) ceramics (330?C and ?? ~115) when measured at 100Hz. However, the Ce-doped SBT (SBCT) ceramics have lower conductivity and dielectric loss.

Thermal enhancement of 2H11/2→4I15/2 up-conversion luminescence of Er3+ doped K2Yb(PO4)(MoO4) phosphors

2021 ◽  
Author(s):  
Hongqiang Cui ◽  
Yongze Cao ◽  
Lei Zhang ◽  
Yuhang Zhang ◽  
Siying Ran ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solid State ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
Orthorhombic Crystal Structure ◽  
Reaction Method ◽  
X Ray ◽  
Thermal Enhancement

Er3+ with different concentrations doped K2Yb(PO4)(MoO4) phosphors were prepared by a solid-state reaction method, and the layered orthorhombic crystal structure of the samples was confirmed by X-ray diffraction (XRD). Under...

Changes in Crystallite Size of Tricalcium Silicate during the Laboratory Grinding

2021 ◽  
Vol 321 ◽  
pp. 23-27
Author(s):  
Simona Ravaszová ◽  
Karel Dvořák
Keyword(s):  
Solid State ◽  
Crystallite Size ◽  
Solid State Reaction ◽  
Solid State Reaction Method ◽  
Tricalcium Silicate ◽  
Planetary Mill ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Grinding Time

The paper is focused on one of the most important component of Portland clinker-on the tricalcium silicate. The study reported in this article is focuses on the changes in crystallite size of synthetic tricalcium silicate obtained using solid state reaction method. Crystallite size changes are monitored during the grinding in three types of laboratory mills in two different conditions. Changing in crystallite size at various grinding time up to 120 minutes are studied with the aid of X-ray diffraction and using the Scherrer equation. It has been found that the most efficient laboratory mill in terms of speed and fineness of the material was the planetary mill.

Dielectric Properties and Raman Spectroscopy in Ca-Substituted Na0.5Bi0.5TiO3 Ferroelectric Ceramics

2011 ◽  
Vol 324 ◽  
pp. 298-301 ◽  
Author(s):  
Roy Jean Roukos ◽  
Olivier Bidault ◽  
Julien Pansiot ◽  
Ludivine Minier ◽  
Lucien Saviot
Keyword(s):  
Raman Spectroscopy ◽  
Dielectric Properties ◽  
Room Temperature ◽  
Rhombohedral Phase ◽  
Xrd Analysis ◽  
Solid State Reaction Method ◽  
Ferroelectric Ceramics ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
X Ray

Lead free Na0.5Bi0.5TiO3 (NBT) and (Na0.5Bi0.5TiO3)1-x(CaTiO3)x (NBT-CT) piezoelectric ceramics with the perovskite structure were studied. The NBT and NBT-CT samples were synthesized using a solid-state reaction method and characterized with X-ray diffraction (XRD), Raman spectroscopy and dielectric measurements for several compositions (x = 0, 0.07, 0.15) at room temperature. The XRD analysis showed a stabilization of a rhombohedral phase at a low concentration of Ca (0 < x <0.15), whereas Raman spectra reveal a strong modification for the sample with x = 0.15. The dielectric properties of these ceramics were studied by measuring impedance in the 79-451K temperature range for unpoled and field cooling with an electric field (FC) conditions.

scholarly journals Dielectric and Raman studies of Ba0.06(Na1/2Bi1/2)0.94TiO3–NaNbO3 ceramics

2016 ◽  
Vol 34 (2) ◽  
pp. 437-445 ◽  
Author(s):  
Sumit K. Roy ◽  
S. Chaudhuri ◽  
R.K. Kotnala ◽  
D.K. Singh ◽  
B.P. Singh ◽  
...  
Keyword(s):  
Single Phase ◽  
Solid State Reaction Method ◽  
Lead Free ◽  
Orthorhombic Symmetry ◽  
Dielectric Studies ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
New Phase ◽  
Diffusivity Parameter

AbstractIn this work the X-ray diffraction, scanning electron microscopy, Raman and dielectric studies of lead free perovskite (1 – x)Ba0.06(Na1/2Bi1/2)0.94TiO3–xNaNbO3 (0 ⩽ x ⩽ 1.0) ceramics, prepared using a standard solid state reaction method, were investigated. X-ray diffraction studies of all the ceramics suggested the formation of single phase with crystal structure transforming from rhombohedral-tetragonal to orthorhombic symmetry with the increase in NaNbO3 content. Raman spectra also confirmed the formation of solid solution without any new phase. Dielectric studies showed that the phase transition is of diffusive character and diffusivity parameter decreases with increasing NaNbO3 content. The compositional fluctuation was considered to be the main cause of diffusivity.

Sign in / Sign up

Export Citation Format

Share Document