Biomimetic liquid lenses actuated by a laser beam: effects of evaporation and orientation to gravity

AbstractLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical multidimensional processes complexity requires a deeper understanding of the impact of laser welding parameters on the quality of welded joints for industrial implementation. The paper presents results of microstructure investigations of laser beam welded stainless steel under various welding parameters. Welded joints was achieved by Ytterbium fiber laser type without the use of the filler material. Material for test was 2205 ferritic-austenitic duplex stainless steel (DSS) plates with thickness of 8 mm in delivery condition. The objectives of this research was to investigate influence of laser welding parameters on weld geometry of butt-welded joints. Investigations of bead shape revealed correlation between laser beam focus position and weld penetration depth.

Download Full-text

A MATHEMATICAL SENSOR MODEL FOR INDOOR USE OF A MULTI-BEAM ROTATING 3D LIDAR

ISPRS - International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences ◽

10.5194/isprs-archives-xlii-2-w16-227-2019 ◽

2019 ◽

Vol XLII-2/W16 ◽

pp. 227-234

Author(s):

L. S. Tessema ◽

R. Jaeger ◽

U. Stilla

Keyword(s):

Laser Beam ◽

Geometric Interpretation ◽

Distortion Correction ◽

Conic Section ◽

Sensor Model ◽

Scan Line ◽

Planar Maps ◽

New Perspective ◽

High Level ◽

3D Lidar

<p><strong>Abstract.</strong> Our contribution presents a new perspective in the mathematical description of a rotating multi-beam LiDAR sensor, in a sense that we make use of projective geometry along with the “homogeneous general equation of the second degree” to parametrize scan lines. We describe the scan geometry of a typical multi-beam rotating 3D LiDAR by representing scan lines as pojective conics that represent a projective figure (a cone) in an embedding plane. This approach enables the parameterization of each scan line using a generic conic section equation. Most modeling approachs model spinning LiDAR sensors in terms of individual points sampled by a laser beam. On the contrary, we propose a model that provides a high-level geometric interpretation both for the environment and the laser scans. Possible application scenarios include exterior and interior calibration of multiple rotating multi-beam sensors, scan distortion correction and localization in planar maps.</p>

Download Full-text

Hybrid Laser-Arc Welding of Thick-Walled, Closed, Circumferential Pipe Welds

Welding Journal ◽

10.29391/2022.101.002 ◽

2022 ◽

Vol 101 (1) ◽

pp. 15-26

Author(s):

ÖMER ÜSTÜNDAĞ ◽

◽

SERGEJ GOOK ◽

ANDREY GUMENYUK ◽

MICHAEL RETHMEIER ◽

...

Keyword(s):

Laser Beam ◽

Arc Welding ◽

Control Strategies ◽

Welding Process ◽

Beam Diameter ◽

Circumferential Welds ◽

Hybrid Laser Arc Welding ◽

Solidification Cracks ◽

High Level ◽

Overlap Area

The application of hybrid laser-arc welding (HLAW) for joining closed circumferential welds is a challenge due to the high risk of forming a defective overlap area with a shrinkage void or solidification cracks in the material thickness. A series of HLAW experiments were performed to understand the development of a faulty overlap area when closing the circumferential weld. Welding trials on flat specimens and pipe segments were supported by numerical analyses in which the thermomechanical behavior of the welds in the overlap area was investigated. Different process control strategies were tested, including variations in defocusing levels and the overlap length. The newly developed HLAW head, including laser optics with a motor-driven collimation system, made it possible to defocus the laser beam during welding without disturbing the stability of the welding process. High-level defocusing of the laser beam of more than 40 mm relative to the specimen surface with a resulting beam diameter of > 2.9 mm, and in combination with a short overlap length of 15 mm, was promising with respect to the formation of a desired cup-shaped weld profile that is resistant to solidification cracks.

Download Full-text

Transcription factor/DNA interactions visualized by electron spectroscopic imaging

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100122654 ◽

1992 ◽

Vol 50 (1) ◽

pp. 450-451

Author(s):

David P. Bazett-Jones ◽

Mark L. Brown

Keyword(s):

Transcription Factor ◽

Dna Sequences ◽

Transcription Initiation ◽

Molecular Mechanisms ◽

Phosphorus Content ◽

Spectroscopic Imaging ◽

Electron Spectroscopic Imaging ◽

Dna Backbone ◽

Two Parameters ◽

High Level

A multisubunit RNA polymerase enzyme is ultimately responsible for transcription initiation and elongation of RNA, but recognition of the proper start site by the enzyme is regulated by general, temporal and gene-specific trans-factors interacting at promoter and enhancer DNA sequences. To understand the molecular mechanisms which precisely regulate the transcription initiation event, it is crucial to elucidate the structure of the transcription factor/DNA complexes involved. Electron spectroscopic imaging (ESI) provides the opportunity to visualize individual DNA molecules. Enhancement of DNA contrast with ESI is accomplished by imaging with electrons that have interacted with inner shell electrons of phosphorus in the DNA backbone. Phosphorus detection at this intermediately high level of resolution (≈lnm) permits selective imaging of the DNA, to determine whether the protein factors compact, bend or wrap the DNA. Simultaneously, mass analysis and phosphorus content can be measured quantitatively, using adjacent DNA or tobacco mosaic virus (TMV) as mass and phosphorus standards. These two parameters provide stoichiometric information relating the ratios of protein:DNA content.

Download Full-text

Two-photon excitation microscopy in cellular biophysics

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100136684 ◽

1995 ◽

Vol 53 ◽

pp. 62-63

Author(s):

David W. Piston ◽

Brian D. Bennett ◽

Robert G. Summers

Keyword(s):

Confocal Microscopy ◽

Laser Beam ◽

Duty Cycle ◽

Excited Electronic State ◽

Input Power ◽

Two Photon ◽

Simultaneous Absorption ◽

Photon Excitation ◽

Very High ◽

Two Photon Excitation

Two-photon excitation microscopy (TPEM) provides attractive advantages over confocal microscopy for three-dimensionally resolved fluorescence imaging and photochemistry. Two-photon excitation arises from the simultaneous absorption of two photons in a single quantitized event whose probability is proportional to the square of the instantaneous intensity. For example, two red photons can cause the transition to an excited electronic state normally reached by absorption in the ultraviolet. In practice, two-photon excitation is made possible by the very high local instantaneous intensity provided by a combination of diffraction-limited focusing of a single laser beam in the microscope and the temporal concentration of 100 femtosecond pulses generated by a mode-locked laser. Resultant peak excitation intensities are 106 times greater than the CW intensities used in confocal microscopy, but the pulse duty cycle of 10-5 maintains the average input power on the order of 10 mW, only slightly greater than the power normally used in confocal microscopy.

Download Full-text

The atomic-force microscope and its future in biology

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100149350 ◽

1993 ◽

Vol 51 ◽

pp. 704-705

Author(s):

Jean-Paul Revel

Keyword(s):

Silicon Nitride ◽

Laser Beam ◽

Atomic Force Microscope ◽

Scanning Tunneling Microscope ◽

Point Of View ◽

Scanning Tunneling ◽

Close Relative ◽

Tunneling Microscope ◽

Atomic Force ◽

Sharp Point

The last few years have been marked by a series of remarkable developments in microscopy. Perhaps the most amazing of these is the growth of microscopies which use devices where the place of the lens has been taken by probes, which record information about the sample and display it in a spatial from the point of view of the context. From the point of view of the biologist one of the most promising of these microscopies without lenses is the scanned force microscope, aka atomic force microscope.This instrument was invented by Binnig, Quate and Gerber and is a close relative of the scanning tunneling microscope. Today's AFMs consist of a cantilever which bears a sharp point at its end. Often this is a silicon nitride pyramid, but there are many variations, the object of which is to make the tip sharper. A laser beam is directed at the back of the cantilever and is reflected into a split, or quadrant photodiode.

Download Full-text

Advances in Stem Instrumentation for Biology

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100180562 ◽

1990 ◽

Vol 48 (1) ◽

pp. 362-363

Author(s):

J. S. Wall

Keyword(s):

Scanning Transmission Electron Microscope ◽

Carbon Films ◽

Specimen Preparation ◽

Material Deposition ◽

Active User ◽

Percent Improvement ◽

Scanning Transmission ◽

The Moment ◽

Film Substrate ◽

High Level

The forte of the Scanning transmission Electron Microscope (STEM) is high resolution imaging with high contrast on thin specimens, as demonstrated by visualization of single heavy atoms. of equal importance for biology is the efficient utilization of all available signals, permitting low dose imaging of unstained single molecules such as DNA.Our work at Brookhaven has concentrated on: 1) design and construction of instruments optimized for a narrow range of biological applications and 2) use of such instruments in a very active user/collaborator program. Therefore our program is highly interactive with a strong emphasis on producing results which are interpretable with a high level of confidence.The major challenge we face at the moment is specimen preparation. The resolution of the STEM is better than 2.5 A, but measurements of resolution vs. dose level off at a resolution of 20 A at a dose of 10 el/A2 on a well-behaved biological specimen such as TMV (tobacco mosaic virus). To track down this problem we are examining all aspects of specimen preparation: purification of biological material, deposition on the thin film substrate, washing, fast freezing and freeze drying. As we attempt to improve our equipment/technique, we use image analysis of TMV internal controls included in all STEM samples as a monitor sensitive enough to detect even a few percent improvement. For delicate specimens, carbon films can be very harsh-leading to disruption of the sample. Therefore we are developing conducting polymer films as alternative substrates, as described elsewhere in these Proceedings. For specimen preparation studies, we have identified (from our user/collaborator program ) a variety of “canary” specimens, each uniquely sensitive to one particular aspect of sample preparation, so we can attempt to separate the variables involved.

Download Full-text

A Questionnaire Survey of Current Rehabilitation Practices for Adults With Normal Hearing Sensitivity Who Experience Auditory Difficulties

American Journal of Audiology ◽

10.1044/2020_aja-20-00027 ◽

2020 ◽

Vol 29 (4) ◽

pp. 738-761

Author(s):

Tess K. Koerner ◽

Melissa A. Papesh ◽

Frederick J. Gallun

Keyword(s):

Hearing Aids ◽

Questionnaire Survey ◽

Patient Population ◽

Clinical Care ◽

Normal Hearing ◽

Auditory Training ◽

Training Methods ◽

Hearing Sensitivity ◽

Considerable Benefit ◽

High Level

Purpose A questionnaire survey was conducted to collect information from clinical audiologists about rehabilitation options for adult patients who report significant auditory difficulties despite having normal or near-normal hearing sensitivity. This work aimed to provide more information about what audiologists are currently doing in the clinic to manage auditory difficulties in this patient population and their views on the efficacy of recommended rehabilitation methods. Method A questionnaire survey containing multiple-choice and open-ended questions was developed and disseminated online. Invitations to participate were delivered via e-mail listservs and through business cards provided at annual audiology conferences. All responses were anonymous at the time of data collection. Results Responses were collected from 209 participants. The majority of participants reported seeing at least one normal-hearing patient per month who reported significant communication difficulties. However, few respondents indicated that their location had specific protocols for the treatment of these patients. Counseling was reported as the most frequent rehabilitation method, but results revealed that audiologists across various work settings are also successfully starting to fit patients with mild-gain hearing aids. Responses indicated that patient compliance with computer-based auditory training methods was regarded as low, with patients generally preferring device-based rehabilitation options. Conclusions Results from this questionnaire survey strongly suggest that audiologists frequently see normal-hearing patients who report auditory difficulties, but that few clinicians are equipped with established protocols for diagnosis and management. While many feel that mild-gain hearing aids provide considerable benefit for these patients, very little research has been conducted to date to support the use of hearing aids or other rehabilitation options for this unique patient population. This study reveals the critical need for additional research to establish evidence-based practice guidelines that will empower clinicians to provide a high level of clinical care and effective rehabilitation strategies to these patients.

Download Full-text