scholarly journals Experimental determination of the induction period for the onset of intensive boiling of a subcooled water flow under conditions of unsteady heat release

2019 ◽  
Vol 114 ◽  
pp. 07004
Author(s):  
A. Safarov ◽  
A. Levin
Keyword(s):  
Experimental Data ◽  
Time Delay ◽  
Water Flow ◽  
Saturation Temperature ◽  
Forced Flow ◽  
Temperature Growth ◽  
Boiling Crisis ◽  
Rapid Temperature ◽  
Vapor Formation

This paper studies prediction of the boiling crisis onset under conditions of the rapid temperature growth of the heat releasing surface washed by a water flow subcooled to the saturation temperature. We obtained experimental data on time delay for rapid vapor formation and showed that the existing technique can be extended to the case with a forced flow. It is shown that the characteristic layer thickness is smaller than the thickness of superheated layer.

scholarly journals Determination of the time scale of photoemission from the measurement of spin polarization

2018 ◽  
Vol 5 (6) ◽  
Author(s):  
Mauro Fanciulli ◽  
Hugo Dil
Keyword(s):  
Experimental Data ◽  
Time Delay ◽  
Matrix Element ◽  
Spin Polarization ◽  
Time Delays ◽  
Upper And Lower Bounds ◽  
Recent Experimental Data ◽  
The Matrix ◽  
Phase Term

The Eisenbud-Wigner-Smith (EWS) time delay of photoemission depends on the phase term of the matrix element describing the transition. Because of an interference process between partial channels, the photoelectrons acquire a spin polarization which is also related to the phase term. The analytical model for estimating the time delay by measuring the spin polarization is reviewed in this manuscript. In particular, the distinction between scattering EWS and interfering EWS time delay will be introduced, providing an insight in the chronoscopy of photoemission. The method is applied to the recent experimental data for Cu(111) presented in M. Fanciulli et al., PRL 118, 067402 (2017), allowing to give better upper and lower bounds and estimates for the EWS time delays.

Equilibrium Sorptions in Heterogeneous Ion Exchange Membranes

1992 ◽  
Vol 57 (9) ◽  
pp. 1905-1914
Author(s):  
Miroslav Bleha ◽  
Věra Šumberová
Keyword(s):  
Experimental Data ◽  
Ion Exchange ◽  
Total Content ◽  
Distribution Coefficients ◽  
Exchange Capacity ◽  
Ion Exchange Membranes ◽  
Ion Exchange Capacity ◽  
Equilibrium Sorption ◽  
Inhomogeneity Factor

The equilibrium sorption of uni-univalent electrolytes (NaCl, KCl) in heterogeneous cation exchange membranes with various contents of the ion exchange component and in ion exchange membranes Ralex was investigated. Using experimental data which express the concentration dependence of equilibrium sorption, validity of the Donnan relation for the systems under investigation was tested and values of the Glueckauf inhomogeneity factor for Ralex membranes were determined. Determination of the equilibrium sorption allows the effect of the total content of internal water and of the ion-exchange capacity on the distribution coefficients of the electrolyte to be determined.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

scholarly journals Determination of cross-sectional void fraction in a two-phase water flow through a PVC pipe

2021 ◽  
Vol 655 (1) ◽  
pp. 012024
Author(s):  
O.H. Ajesi ◽  
M.B. Latif ◽  
S.T. Gbenu ◽  
C. A. Onumejor ◽  
M. K. Fasasi ◽  
...  
Keyword(s):  
Water Flow ◽  
Void Fraction ◽  
Two Phase ◽  
Cross Sectional ◽  
Flow Through ◽  
Pvc Pipe ◽  
Phase Water

A Technique for the Laboratory Determination of Recirculation in Single Needle Dialysis

1993 ◽  
Vol 16 (2) ◽  
pp. 63-70 ◽  
Author(s):  
N.A. Hoenich ◽  
P.T. Smirthwaite ◽  
C. Woffindin ◽  
P. Lancaster ◽  
T.H. Frost ◽  
...  
Keyword(s):  
Experimental Data ◽  
Flow Rate ◽  
Experimental Results ◽  
New Technique ◽  
Treatment Efficiency ◽  
Single Lumen ◽  
Theoretical Predictions ◽  
Lumen Catheter ◽  
A New Technique

Recirculation is an important factor in single needle dialysis and, if high, can compromise treatment efficiency. To provide information regarding recirculation characteristics of access devices used in single needle dialysis, we have developed a new technique to characterise recirculation and have used this to measure the recirculation of a Terumo 15G fistula needle and a VasCath SC2300 single lumen catheter. The experimentally obtained results agreed well with those established clinically (8.5 ± 2.4% and 18.4 ± 3.4%). The experimental results have also demonstrated a dependence on access type, pump speeds and fistula flow rate. A comparison of experimental data with theoretical predictions showed that the latter exceeded those measured with the largest contribution being due to the experimental fistula.

Theoretical determination of the structures of CaSiO3 perovskites

2006 ◽  
Vol 62 (6) ◽  
pp. 1025-1030 ◽  
Author(s):  
Razvan Caracas ◽  
Renata M. Wentzcovitch
Keyword(s):  
Crystal Structure ◽  
Experimental Data ◽  
Density Functional Theory ◽  
Density Functional ◽  
Theoretical Determination ◽  
Functional Theory ◽  
Starting Point ◽  
Atomic Coordinates ◽  
The Ideal

Density functional theory is used to determine the possible crystal structure of the CaSiO3 perovskites and their evolution under pressure. The ideal cubic perovskite is considered as a starting point for studying several possible lower-symmetry distorted structures. The theoretical lattice parameters and the atomic coordinates for all the structures are determined, and the results are discussed with respect to experimental data.

A Critical Review on the Determination of Pressure Drop During Condensation in Smooth and Enhanced Tubes

2013 ◽  
Author(s):  
Ahmet Selim Dalkiliç ◽  
Ali Celen ◽  
Mohamed M. Awad ◽  
Somchai Wongwises
Keyword(s):  
Neural Network ◽  
Heat Transfer ◽  
Experimental Data ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Review ◽  
Heat Exchangers ◽  
Numerical Analyses ◽  
Enhanced Tubes

Heat exchangers using in-tube condensation have great significance in the refrigeration, automotive and process industries. Effective heat exchangers have been rapidly developed due to the demand for more compact systems, higher energy efficiency, lower material costs and other economic incentives. Enhanced surfaces, displaced enhancement devices, swirl-flow devices and surface tension devices improve the heat transfer coefficients in these heat exchangers. This study is a critical review on the determination of the condensation heat transfer coefficient of pure refrigerants flowing in vertical and horizontal tubes. The authors’ previous publications on this issue, including the experimental, theoretical and numerical analyses are summarized here. The lengths of the vertical and horizontal test sections varied between 0.5 m and 4 m countercurrent flow double-tube heat exchangers with refrigerant flowing in the inner tube and cooling water flowing in the annulus. The measured data are compared to theoretical and numerical predictions based on the solution of the artificial intelligence methods and CFD analyses for the condensation process in the smooth and enhanced tubes. The theoretical solutions are related to the design of double tube heat exchangers in refrigeration, air conditioning and heat pump applications. Detailed information on the in-tube condensation studies of heat transfer coefficient in the literature is given. A genetic algorithm (GA), various artificial neural network models (ANN) such as multilayer perceptron (MLP), radial basis networks (RBFN), generalized regression neural network (GRNN), and adaptive neuro-fuzzy inference system (ANFIS), and various optimization techniques such as unconstrained nonlinear minimization algorithm-Nelder-Mead method (NM), non-linear least squares error method (NLS), and Ansys CFD program are used in the numerical solutions. It is shown that the convective heat transfer coefficient of laminar and turbulent condensing film flows can be predicted by means of theoretical and numerical analyses reasonably well if there is a sufficient amount of reliable experimental data. Regression analysis gave convincing correlations, and the most suitable coefficients of the proposed correlations are depicted as compatible with the large number of experimental data by means of the computational numerical methods.

Sign in / Sign up

Export Citation Format

Share Document