scholarly journals The influence of acoustic power on chemical absorption of CO2 using Slow Kinetic Solvent

2021 ◽  
Vol 287 ◽  
pp. 01002
Author(s):  
Fatemeh Shokrollahi ◽  
Lau Kok Keong
Keyword(s):  
High Frequency ◽  
Acoustic Power ◽  
Operating Conditions ◽  
Ultrasonic Power ◽  
Absorption Process ◽  
Absorption System ◽  
Chemical Absorption ◽  
Ultrasonic Assisted ◽  
Enhance Mass ◽  
Slow Kinetic

Ultrasonic Irradiation (UI) is an emerging technology that is used to assist the CO2 absorption process. Even for the slow kinetic solvents without using any chemical promoter, high-frequency UI might enhance mass transfer during the absorption process. For this purpose, it is essential to study the performance of a high-frequency ultrasonic-assisted absorption system under varied operating conditions. The ultrasonic power is considered as one of the main parameters during the absorption of CO2. Thus, in this paper, the influence of ultrasonic power is presented using Methyl diethanolamine (MDEA) as a chemical solvent. The ultrasonic power has been varied from 0 to 15.3 W. The results tend to show a significant absorption rate enhancement for higher ultrasonic power. Moreover, they prove that the high-frequency ultrasonic absorption system has high potential to be utilized to enhance the absorption using promoter-free MDEA.

Research Trends of Carbon Dioxide Capture using Ionic Liquids and Aqueous Amine-Ionic Liquids Mixtures

2016 ◽  
Vol 13 (1) ◽  
pp. 53
Author(s):  
Siti Nabihah Jamaludin ◽  
Ruzitah Mohd Salleh
Keyword(s):  
Ionic Liquids ◽  
Co2 Capture ◽  
Membrane Separation ◽  
Carbon Dioxide Capture ◽  
Global Climate ◽  
Research Trends ◽  
Co2 Absorption ◽  
Absorption Process ◽  
Chemical Absorption ◽  
Factors Influencing

Anthropogenic CO2 emissions has led to global climate change and widely contributed to global warming since its concentration has been increasing over time. It has attracted vast attention worldwide. Currently, the different CO2 capture technologies available include absorption, solid adsorption and membrane separation. Chemical absorption technology is regarded as the most mature technology and is commercially used in the industry. However, the key challenge is to find the most efficient solvent in capturing CO2. This paper reviews several types of CO2 capture technologies and the various factors influencing the CO2 absorption process, resulting in the development of a novel solvent for CO2 capture.

EFFECTIVENESS FACTOR APPROACH FOR CHEMICAL ABSORPTION PROCESS

2018 ◽  
Vol 17 (4) ◽  
pp. 813-820 ◽  
Author(s):  
Lacramioara Rusu ◽  
Maria Harja ◽  
Gabriela Ciobanu ◽  
Liliana Lazar
Keyword(s):  
Effectiveness Factor ◽  
Absorption Process ◽  
Chemical Absorption

scholarly journals Optimization of Ultrasonic-Assisted Extraction, Characterization, and Antioxidant Activities of Polysaccharides From Sojae Semen Praeparatum

2021 ◽  
Vol 16 (5) ◽  
pp. 1934578X2110206
Author(s):  
Yongshuai Jing ◽  
Ruijuan Zhang ◽  
Lan Li ◽  
Danshen Zhang ◽  
Yu Liu ◽  
...  
Keyword(s):  
Antioxidant Activities ◽  
Deae Cellulose ◽  
Chemical Compositions ◽  
Hydroxyl Groups ◽  
Ultrasonic Frequency ◽  
Ultrasonic Power ◽  
Assisted Extraction ◽  
Ultrasonic Time ◽  
Ultrasonic Assisted ◽  
Ultrasonic Assisted Extraction

In this study, response surface methodology (RSM) was used to optimize the ultrasonic-assisted extraction parameters of Sojae Semen Praeparatum polysaccharides (SSPP-80), the optimum conditions were determined as follows: ultrasonic frequency of 100 W, ultrasonic power of 80 Hz, ultrasonic temperature of 52℃, ultrasonic time of 23 minutes, and liquid to raw material ratio of 40 mL/g. Based on these conditions, polysaccharides extraction rate was 7.72% ± 0.26%. Then, 2 novel polysaccharides (SSPP-80‐1, SSPP-80‐2) were isolated from SSPP by DEAE-cellulose 52 chromatography. The chemical compositions, physicochemical properties, and structure of SSPPs were investigated by simultaneous thermal analyzer (TGA), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FI-IR), and high-performance liquid chromatography (HPLC). The results showed that SSPP-80 and 2 fractions were mainly composed of mannose (Man), glucose (Glc), galactose (Gal), xylose (Xyl), and arabinose (Ara). In addition, the antioxidant activities were evaluated against the DPPH and hydroxyl radical in vitro, the IC50 of SSPP-80, SSPP-80‐1 and SSPP-80‐2 against DPPH free radical were 4.407, 8.267, and 5.204 mg/mL, respectively, whereas the IC50values for removing hydroxyl groups were 5.318, 3.516, and 4.016 mg/mL, respectively. It demonstrated that SSPP-80 and 2 fractions had certain antioxidant activity. Theoretical basis for use of Sojae Semen Praeparatum polysaccharides was provided by this study.

Environmental and economic assessment of the chemical absorption process in Korea using the LEAP model

Energy Policy ◽  
2007 ◽  
Vol 35 (10) ◽  
pp. 5109-5116 ◽  
Author(s):  
Ho-Jun Song ◽  
Seungmoon Lee ◽  
Sanjeev Maken ◽  
Se-Woong Ahn ◽  
Jin-Won Park ◽  
...  
Keyword(s):  
Economic Assessment ◽  
Absorption Process ◽  
Chemical Absorption

scholarly journals Experimental Investigation and Modeling of Inertance Tubes

2005 ◽  
Vol 127 (5) ◽  
pp. 1029-1037 ◽  
Author(s):  
L. O. Schunk ◽  
G. F. Nellis ◽  
J. M. Pfotenhauer
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Acoustic Power ◽  
Operating Conditions ◽  
Thermodynamic Efficiency ◽  
Pulse Tube ◽  
Design Charts ◽  
Wide Range ◽  
Pulse Tube Refrigerators

Growing interest in larger scale pulse tubes has focused attention on optimizing their thermodynamic efficiency. For Stirling-type pulse tubes, the performance is governed by the phase difference between the pressure and mass flow, a characteristic that can be conveniently adjusted through the use of inertance tubes. In this paper we present a model in which the inertance tube is divided into a large number of increments; each increment is represented by a resistance, compliance, and inertance. This model can include local variations along the inertance tube and is capable of predicting pressure, mass flow rate, and the phase between these quantities at any location in the inertance tube as well as in the attached reservoir. The model is verified through careful comparison with those quantities that can be easily and reliably measured; these include the pressure variations along the length of the inertance tube and the mass flow rate into the reservoir. These experimental quantities are shown to be in good agreement with the model’s predictions over a wide range of operating conditions. Design charts are subsequently generated using the model and are presented for various operating conditions in order to facilitate the design of inertance tubes for pulse tube refrigerators. These design charts enable the pulse tube designer to select an inertance tube geometry that achieves a desired phase shift for a given level of acoustic power.

Numerical Simulation of Plunge Force During the Plunge Phase of Friction Stir Welding and Ultrasonic Assisted FSW

2008 ◽  
Author(s):  
Kwanghyun Park ◽  
Bongsuk Kim ◽  
Jun Ni
Keyword(s):  
Numerical Simulation ◽  
Friction Stir Welding ◽  
High Frequency ◽  
Hybrid Welding ◽  
Ultrasonic Vibrations ◽  
Welding Quality ◽  
Friction Stir ◽  
Ultrasonic Assisted ◽  
Welding Force ◽  
Welding Technique

Ultrasonic assisted friction stir welding (UaFSW) is an hybrid welding technique, where high frequency vibration is superimposed on the movement of a rotating tool. The benefit of using ultrasonic vibration in the FSW process refers to the reduction in the welding force and to the better welding quality. The UaFSW system is being developed and its mechanism needs to be understood using both the experiments and the numerical simulations. In this paper, FE simulations of FSW and UaFSW using ABAQUS/Explicit were carried out to examine plunge forces during the plunge phase of FSW and UaFSW, respectively. First, the simulations of the conventional FSW process were validated. Then, simulation of UaFSW process was performed by imposing sinusoidal horizontal ultrasonic vibrations on the tool.

Simulating Ultrasound Piezoelectric Power Transfer in the Near Field and Experimental Validations

2021 ◽  
Vol 05 ◽  
Author(s):  
Ammar Mohammed ◽  
Changki Mo ◽  
John Miller ◽  
David Lowry ◽  
Jassim Alhamid
Keyword(s):  
Energy Transfer ◽  
Lead Zirconate Titanate ◽  
Near Field ◽  
Acoustic Power ◽  
Acoustic Energy ◽  
Transfer Efficiency ◽  
Ultrasonic Power ◽  
Power Transfer ◽  
Piezoelectric Energy ◽  
Power Transfer Efficiency

Background: Acoustic power transfer is a method for wireless energy transfer to implanted medical devices that permits a greater range of separation between transmitter and receiver than is possible with inductive power transfer. In some cases, short-distance ultrasonic power transfer may be employed; consequently, their operation may be complicated by the near-field aspects of piezoelectric acoustic energy transfer. Methods: A piezoelectric energy transfer system consisting of two lead zirconate titanate (PZT) transducers was analyzed in this work using a combination of experimental measurements and computer simulations. Results: Simulations using the COMSOL Software package showed good agreement with a measured output voltage as a function of the distance between and alignment of the transmitter and receiver with water as a medium. We also simulated how operating frequency affects power transfer efficiency at various distances between the transmitter and receiver and found reasonable agreement with experiments. We report model predictions for power transfer efficiency as a function of the thickness and diameter of the transmitter and receiver. Conclusion: The results show that with proper choice of parameters, piezoelectric systems can provide high power transfer efficiency in the near-field region.

Membrane Evaporation for Energy Saving in CO2 Chemical Absorption Process Using a Polybenzimidazole Film: Mass and Heat Transfer

2017 ◽  
Vol 31 (10) ◽  
pp. 11091-11098 ◽  
Author(s):  
Qinhui Ma ◽  
Mengxiang Fang ◽  
Tao Wang ◽  
Hai Yu ◽  
Paul H. M. Feron
Keyword(s):  
Heat Transfer ◽  
Energy Saving ◽  
Absorption Process ◽  
Chemical Absorption ◽  
Mass And Heat Transfer
Sign in / Sign up

Export Citation Format

Share Document