scholarly journals A new slick water system for hydraulic fracturing in tight reservoir to enhance imbibition oil recovery

2021 ◽  
Vol 303 ◽  
pp. 01001
Author(s):  
Yu Haiyang ◽  
Ji Wenjuan ◽  
Luo Cheng ◽  
Lu Junkai ◽  
Yan Fei ◽  
...  
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
Water System ◽  
Natural Fracture ◽  
Fracturing Fluid ◽  
The Core ◽  
Ultralow Permeability

In order to give full play to the role of imbibition of capillary force and enhance oil recovery of ultralow permeability sandstone reservoir after hydraulic fracturing, the mixed water fracture technology based on functional slick water is described and successfully applied to several wells in oilfield. The core of the technology is determination of influence factors of imbibition oil recovery, the development of new functional slick water system and optimization of volume fracturing parameters. The imbibition results show that it is significant effect of interfacial tension, wetting on imbibition oil recovery. The interfacial tension decreases by an order of magnitude, the imbibition oil recovery reduces by more than 10%. The imbibition oil recovery increases with the contact angle decreasing. The emulsifying ability has no obvious effect on imbibition oil recovery. The functional slick water system considering imbibition is developed based on the solution rheology and polymer chemistry. The system has introduced the active group and temperature resistant group into the polymer molecules. The molecular weight is controlled in 1.5 million. The viscosity is greater than 2mPa·s after shearing 2h under 170s-1 and 100℃. The interfacial tension could decrease to 10-2mN/m. The contact angle decreased from 58° to 22° and the core damage rate is less than 12%. The imbibition oil recovery could reach to 43%. The fracturing process includes slick water stage and linear gel stage. 10% 100 mesh ceramists and 8% temporary plugging agents are carried into the formation by functional slick water. 40-70 mesh ceramists are carried by linear gel. The liquid volume ratio is about 4:1 and the displacement is controlled at 10-12m3/min. The sand content and fracturing fluid volumes of single stage are 80m3 and 2500 m3 respectively. Compared with conventional fracturing, due to imbibition oil recovery, there is only 25% of the fracturing fluid flowback rate when the crude oil flew out. When the oil well is in normal production, about 50% of the fracturing fluid is not returned. It is useful to maintain the formation energy and slow down the production decline. The average cumulative production of vertical wells is greater than 2800t, and the effective period is more than 2 years. This technology overcoming the problem of high horizontal stress difference and lack of natural fracture has been successfully applied in Jidong Oilfield ultralow permeability reservoir. The successful application of this technology not only helps to promote the effective use of ultralow permeability reservoirs, but also helps to further clarify the role of imbibition recovery, energy storage and oil-water replacement mechanism.

scholarly journals A Core Flood and Microfluidics Investigation of Nanocellulose as a Chemical Additive to Water Flooding for EOR

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1296 ◽  
Author(s):  
Reidun C. Aadland ◽  
Salem Akarri ◽  
Ellinor B. Heggset ◽  
Kristin Syverud ◽  
Ole Torsæter
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Cellulose Nanofibrils ◽  
Water Flooding ◽  
Low Salinity ◽  
The Core ◽  
Low Salinity Water ◽  
Salinity Water ◽  
Core Flood

Cellulose nanocrystals (CNCs) and 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-oxidized cellulose nanofibrils (T-CNFs) were tested as enhanced oil recovery (EOR) agents through core floods and microfluidic experiments. Both particles were mixed with low salinity water (LSW). The core floods were grouped into three parts based on the research objectives. In Part 1, secondary core flood using CNCs was compared to regular water flooding at fixed conditions, by reusing the same core plug to maintain the same pore structure. CNCs produced 5.8% of original oil in place (OOIP) more oil than LSW. For Part 2, the effect of injection scheme, temperature, and rock wettability was investigated using CNCs. The same trend was observed for the secondary floods, with CNCs performing better than their parallel experiment using LSW. Furthermore, the particles seemed to perform better under mixed-wet conditions. Additional oil (2.9–15.7% of OOIP) was produced when CNCs were injected as a tertiary EOR agent, with more incremental oil produced at high temperature. In the final part, the effect of particle type was studied. T-CNFs produced significantly more oil compared to CNCs. However, the injection of T-CNF particles resulted in a steep increase in pressure, which never stabilized. Furthermore, a filter cake was observed at the core face after the experiment was completed. Microfluidic experiments showed that both T-CNF and CNC nanofluids led to a better sweep efficiency compared to low salinity water flooding. T-CNF particles showed the ability to enhance the oil recovery by breaking up events and reducing the trapping efficiency of the porous medium. A higher flow rate resulted in lower oil recovery factors and higher remaining oil connectivity. Contact angle and interfacial tension measurements were conducted to understand the oil recovery mechanisms. CNCs altered the interfacial tension the most, while T-CNFs had the largest effect on the contact angle. However, the changes were not significant enough for them to be considered primary EOR mechanisms.

scholarly journals The Effect of Carbonyl and Hydroxyl Compounds on Swelling Factor, Interfacial Tension, and Viscosity in CO2 Injection: A Case Study on Aromatic Oils

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 94
Author(s):  
Asep Kurnia Permadi ◽  
Egi Adrian Pratama ◽  
Andri Luthfi Lukman Hakim ◽  
Doddy Abdassah
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Viscosity Reduction ◽  
Co2 Injection ◽  
Minimum Miscibility Pressure ◽  
Lower Viscosity ◽  
Hydroxyl Compounds ◽  
Swelling Factor

A factor influencing the effectiveness of CO2 injection is miscibility. Besides the miscible injection, CO2 may also contribute to oil recovery improvement by immiscible injection through modifying several properties such as oil swelling, viscosity reduction, and the lowering of interfacial tension (IFT). Moreover, CO2 immiscible injection performance is also expected to be improved by adding some solvent. However, there are a lack of studies identifying the roles of solvent in assisting CO2 injection through observing those properties simultaneously. This paper explains the effects of CO2–carbonyl and CO2–hydroxyl compounds mixture injection on those properties, and also the minimum miscibility pressure (MMP) experimentally by using VIPS (refers to viscosity, interfacial tension, pressure–volume, and swelling) apparatus, which has a capability of measuring those properties simultaneously within a closed system. Higher swelling factor, lower viscosity, IFT and MMP are observed from a CO2–propanone/acetone mixture injection. The role of propanone and ethanol is more significant in Sample A1, which has higher molecular weight (MW) of C7+ and lower composition of C1–C4, than that in the other Sample A9. The solvents accelerate the ways in which CO2 dissolves and extracts oil, especially the extraction of the heavier component left in the swelling cell.

scholarly journals Mechanism of active silica nanofluids based on interface-regulated effect during spontaneous imbibition

2021 ◽  
Author(s):  
Xu-Guang Song ◽  
Ming-Wei Zhao ◽  
Cai-Li Dai ◽  
Xin-Ke Wang ◽  
Wen-Jiao Lv
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Dynamic Contact Angle ◽  
Liquid Interface ◽  
Spontaneous Imbibition ◽  
Wettability Alteration ◽  
Low Permeability ◽  
Oil Water ◽  
Solid Liquid

AbstractThe ultra-low permeability reservoir is regarded as an important energy source for oil and gas resource development and is attracting more and more attention. In this work, the active silica nanofluids were prepared by modified active silica nanoparticles and surfactant BSSB-12. The dispersion stability tests showed that the hydraulic radius of nanofluids was 58.59 nm and the zeta potential was − 48.39 mV. The active nanofluids can simultaneously regulate liquid–liquid interface and solid–liquid interface. The nanofluids can reduce the oil/water interfacial tension (IFT) from 23.5 to 6.7 mN/m, and the oil/water/solid contact angle was altered from 42° to 145°. The spontaneous imbibition tests showed that the oil recovery of 0.1 wt% active nanofluids was 20.5% and 8.5% higher than that of 3 wt% NaCl solution and 0.1 wt% BSSB-12 solution. Finally, the effects of nanofluids on dynamic contact angle, dynamic interfacial tension and moduli were studied from the adsorption behavior of nanofluids at solid–liquid and liquid–liquid interface. The oil detaching and transporting are completed by synergistic effect of wettability alteration and interfacial tension reduction. The findings of this study can help in better understanding of active nanofluids for EOR in ultra-low permeability reservoirs.

scholarly journals Carbon dioxide adsorption and interaction with formation fluids of Jordanian unconventional reservoirs

2021 ◽  
Author(s):  
H. Samara ◽  
T. V. Ostrowski ◽  
F. Ayad Abdulkareem ◽  
E. Padmanabhan ◽  
P. Jaeger
Keyword(s):  
Carbon Dioxide ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Gas Adsorption ◽  
Sessile Drop ◽  
Global Climate ◽  
Gravimetric Method ◽  
Rock Surface ◽  
Operating Pressure

AbstractShales are mostly unexploited energy resources. However, the extraction and production of their hydrocarbons require innovative methods. Applications involving carbon dioxide in shales could combine its potential use in oil recovery with its storage in view of its impact on global climate. The success of these approaches highly depends on various mechanisms taking place in the rock pores simultaneously. In this work, properties governing these mechanisms are presented at technically relevant conditions. The pendant and sessile drop methods are utilized to measure interfacial tension and wettability, respectively. The gravimetric method is used to quantify CO2 adsorption capacity of shale and gas adsorption kinetics is evaluated to determine diffusion coefficients. It is found that interfacial properties are strongly affected by the operating pressure. The oil-CO2 interfacial tension shows a decrease from approx. 21 mN/m at 0.1 MPa to around 3 mN/m at 20 MPa. A similar trend is observed in brine-CO2 systems. The diffusion coefficient is observed to slightly increase with pressure at supercritical conditions. Finally, the contact angle is found to be directly related to the gas adsorption at the rock surface: Up to 3.8 wt% of CO2 is adsorbed on the shale surface at 20 MPa and 60 °C where a maximum in contact angle is also found. To the best of the author’s knowledge, the affinity of calcite-rich surfaces toward CO2 adsorption is linked experimentally to the wetting behavior for the first time. The results are discussed in terms of CO2 storage scenarios occurring optimally at 20 MPa.

Success Story of Optimizing Hydraulic Fracturing Design at Alpha Low-Permeability Reservoir

2021 ◽  
Author(s):  
Mario Hadinata Prasetio ◽  
Hanny Anggraini ◽  
Hendro Tjahjono ◽  
Aditya Bintang Pramadana ◽  
Aulia Akbari ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Oil Recovery ◽  
History Matching ◽  
Initial Period ◽  
Earth Model ◽  
Low Permeability ◽  
Stress Profile ◽  
Reservoir Pressure ◽  
Fracturing Fluid ◽  
Fracture Closure

Abstract This paper describes the evolution of the hydraulic fracturing approach and design in the Alpha reservoir over the past years. Alpha reservoir in XYZ field is a laminated sandstone reservoir with low permeability in the range of 20 to 140 md at a depth of approximately 4,000 to 4,500 ft true vertical depth (TVD). XYZ field is located in Rokan block, Riau, Central Sumatra region. Due to Alpha reservoir's nature, producing from this reservoir commercially requires stimulation. Hydraulic fracturing has been applied as the selected stimulation method to increase productivity from this reservoir. However, several challenges were recognized during the initial period, such as depleted reservoir pressure, indication of fracture height growth, and low to medium Young's modulus, which leads to few screened-out cases as well as low production gain after the fracturing treatment. The fracturing job in Alpha reservoir has been applied since 2002. However, pressure depletion was observed through this time until waterflood optimization started in May 2018 by converting commingled injection to injection dedicated to the Alpha reservoir. The pressure responded and increased from 350 psi to approximately 800 psi. Hence this reservoir still cannot be produced in single completion without the hydraulic fracturing job due to laminated reservoir and low-permeability character. A detailed look at the mechanical earth model (MEM) was done to revise the elastic properties and stress profile considering reservoir pressure change. The revised model was later used as an input for fracture geometry simulation. Calibration injection tests were performed and analyzed prior to the main fracturing treatments to determine fracture closure pressure and leakoff characteristics, which led to fracturing fluid efficiency. Results of these tests were used in job modifications regarding pad percentage, fracturing fluid rheology, proppant volume, and proppant concentration. Pressure history matching both after fracturing and in real time as well as the temperature log were used to validate the MEM and fracture geometries. Each change, approach, and impact were documented and statistically analyzed to determine a generic trend and design envelope for the Alpha reservoir. Between 2019 and 2020, nine wells were stimulated that specifically targeted the Alpha reservoir, with continuous improvement in fracturing design and geomechanics properties with each well. After fracturing, the 30-day oil recovery was superior, higher than previous fractured wells, reaching more than 255 BFPD on average. The successful development of the Alpha reservoir with hydraulic fracturing led to further milestones to maximize oil recovery in XYZ field.

Experimental Simulation on Imbibition of the Residual Fracturing Fluid in Tight Sandstone Reservoirs

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Xiaoxia Ren ◽  
Aifen Li ◽  
Asadullah Memon ◽  
Shuaishi Fu ◽  
Guijuan Wang ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Oil Recovery ◽  
Experimental Simulation ◽  
Fluid Distribution ◽  
Oil Viscosity ◽  
Pore Throat ◽  
Fracturing Fluid ◽  
Tight Sandstone ◽  
The Difference ◽  
Displacement Processes

Fracturing is a fundamental technique for enhancing oil recovery of tight sandstone reservoir. The pores in tight reservoirs generally have small radii and generate tremendous capillary force; accordingly, the imbibition effect can significantly affect retention and absorption of the fracturing fluid. In this study, the imbibition behaviors of the fracturing fluid were experimentally investigated, and the effects of interfacial tension, (IFT) permeability, oil viscosity, and the salinity of the imbibition fluid were determined. In addition, combining with nuclear magnetic resonance (NMR)-based core analysis, fluid distribution, and the related variations in imbibition and displacement processes were analyzed. Finally, some key influencing factors of imbibition of the residual fracturing fluid, the difference and correlation between imbibition and displacement, as well as the contribution of imbibition to displacement were explored so as to provide optimization suggestions for guiding the application of oil-displacing fracturing fluid in exploration. Results show that imbibition recovery increased with time, but the imbibition rate gradually dropped. There exists an optimal interfacial tension that corresponds to maximum imbibition recovery. In addition, imbibition recovery increased as permeability and salinity increases and oil viscosity decreases. Furthermore, it was found that extracted oil from the movable pore throat space was almost equal to that from the irreducible pore throat space during imbibition and their contribution in the irreducible pore throat space was greater than in the movable pore throat space in the displacement process. Hence, imbibition plays a more important role during the displacement process in the reservoirs with finer porous structure than previously thought.

scholarly journals The Role of Salinity and Brine Ions in Interfacial Tension Reduction While Using Surfactant for Enhanced Oil Recovery

2015 ◽  
Vol 9 (9) ◽  
pp. 722-726 ◽  
Author(s):  
S.N. Hosseini ◽  
M.T. Shuker ◽  
Z. Hosseini ◽  
T. Joao Tomocene ◽  
A. Shabib-asl ◽  
...  
Keyword(s):  
Interfacial Tension ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Tension Reduction

scholarly journals Synthesis of Guerbet Amine-Oxide for Enhanced Oil Recovery

2020 ◽  
Vol 2020 ◽  
pp. 1-6
Author(s):  
Changxin Shi ◽  
Zhiping Li ◽  
Hong Zhang ◽  
Yajuan Chen ◽  
Minglong Zhang ◽  
...  
Keyword(s):  
Hydrogen Peroxide ◽  
Binary System ◽  
Critical Micelle Concentration ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Mass Spectra ◽  
Amine Oxide ◽  
The Core ◽  
Ft Ir ◽  
Core Flood

Guerbet amine-oxide was synthesized by using Guerbet acid, N,N′-diethyl-1,3-propanediamine and hydrogen peroxide. Its structure was confirmed by FT-IR spectra and mass spectra. The critical micelle concentration (CMC) and the interfacial tension between the crude oil and water were measured. The results showed that the CMC of the Guerbet amine-oxide is 2.14 × 10−5 mol/L and the interfacial tension could be lowered to ultralow levels. The core flood test showed that the surfactant and polymer binary system could increase oil recovery by 24.7% above the water flood.

Sign in / Sign up

Export Citation Format

Share Document