scholarly journals Effect of Hybridization on the Mechanical Properties of Chopped Strand Mat/Pineapple Leaf Fibre Reinforced Polyester Composites

2018 ◽  
Vol 153 ◽  
pp. 01006 ◽  
Author(s):  
Suhas Yeshwant Nayak ◽  
Srinivas Shenoy Heckadka ◽  
Nishank Minil Amin ◽  
Ramakrishna Vikas Sadanand ◽  
Linto George Thomas
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Polymer Composites ◽  
Matrix Cracking ◽  
Reinforced Composites ◽  
Pull Out ◽  
The Matrix ◽  
Chopped Strand Mat ◽  
Hybrid Laminate

Hybridization of synthetic and natural fibres as reinforcement makes the polymer composites environmental friendly and sustainable when compared to synthetic fibres based polymer composites. In this study chopped strand mat/pineapple leaf fibres were hybridized. Four laminates with six layers each, with different stack sequence (GGGGGG, GPPPPG, PGGGGP and PPPPPP) were fabricated using hand layup technique while maintaining a fibre to matrix ratio of 30:70 by weight with polyester resin as matrix. Mechanical properties such as tensile and flexural strength were determined and morphology of fractured specimens was studied. Maximum tensile strength of 180 MPa was obtained for the laminate with six layers of chopped strand mat followed by hybrid laminate with four layers of chopped strand mat at the centre (120 MPa). Tensile strength of hybrid laminate with four layers of pineapple leaf fibres at the centre was in third position at 86 MPa. Least tensile strength of 65 MPa was obtained for the laminate with six layers of pineapple leaf fibres. Similar trend was observed in case of flexural behaviour of the laminates with maximum flexural strength of 255 MPa and minimum flexural strength 107 MPa. Scanning electron microscopy of the fractured specimen reinforced with chopped strand mat only, indicated, fibre pull out, matrix cracking and lack of matrix adhesion to fibres. In case of hybrid composite (GPPPPG and PGGGGP) delamination was observed to be prominent due to improper wetting of the pineapple leaf fibres with the matrix. More significant delamination led to lesser strength in case of pineapple fibres reinforced composites even though the fibre pull out was relatively less.

Influence of the Composition of Cement Mortars Modified by Lime or Polymers on the Mechanical Properties and Microstructure of Mortars

2013 ◽  
Vol 592-593 ◽  
pp. 647-650 ◽  
Author(s):  
Małgorzata Lenart
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Polyvinyl Alcohol ◽  
Polymer Composites ◽  
Adhesion Strength ◽  
Hardened Cement ◽  
Cement Mortars ◽  
Styrene Butadiene

Cement – polymer composites are nowadays widely used in repair systems not only in case of concrete or reinforced concrete constructions but also in masonry. Polymers addition for example already at 5% m.c. modifies the structure of the cement – polymer composite in a way that many of the mechanical properties such as flexural strength, tensile strength or adhesion to substrates are improved. The paper presents the results of tests such as flexural, compressive or adhesion strength to ceramic substrate of hardened cement mortars with different composition, as well as selected cement mortars modified by two polymers: polyvinyl alcohol and styrene – butadiene polymer dosed at 5 % m.c. Four types of cement mortars modified by lime (component used in historical constructions as well as in contemporary masonry mortars) are also examined for comparison.

scholarly journals Comparison of Mechanical Properties of Biaxial and Triaxial Fabric and Composites Reinforced by Them

2019 ◽  
Vol 27 (1(133)) ◽  
pp. 37-44
Author(s):  
Marcin Barburski ◽  
Mariusz Urbaniak ◽  
Sanjeeb Kumar Samal
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Resin Matrix ◽  
Reinforced Composites ◽  
Reinforced Composite ◽  
Aramid Fabrics ◽  
Properties Of Composites

In this article, the mechanical properties of biaxial and triaxial woven aramid fabric and respective reinforced composites were investigated. Both fabrics had the same mass/m2. The first part of the experimental investigation was focused on the mechanical properties of different non-laminated aramid fabrics (biaxial and triaxial). The second part was concerned with the mechanical properties of composites made of a different combination of layers of fabric reinforced with an epoxy resin matrix in the order of biaxial+biaxial, trixial+triaxial and biaxial+triaxial. The composites were tested for tensile strength, flexural strength, strain and Young’s and flexural modulus. It can be seen from the results that the density and direction of the yarns are the most important parameters for determination of the strength of the fabric reinforced composite. The biaxial composite clearly showed better tensile strength, while the bi-tri axial order showed good flexural strength compared to the other composite combinations. These fabric reinforced composites have suitable applications in the areas of medical, protection and in the automotive industries.

Investigation on Effect of Varying Weight Percentage of Glass Fiber and Filler on the Properties of Glass Fiber-Cement- Polyester Composites

2020 ◽  
Vol 995 ◽  
pp. 117-122
Author(s):  
Phaneesh Shettigar ◽  
Manjunath Shettar ◽  
Rao U. Sathish ◽  
C.S. Suhas Kowshik ◽  
M.C. Gowrishankar
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Polyester Resin ◽  
Tensile Load ◽  
Weight Percentage ◽  
Pull Out ◽  
The Matrix ◽  
Polyester Composites

In this research, the results of different weight percentage of glass fiber (30, 40 & 50), cement (0, 3 & 6) and polyester resin (70, 60 & 50), on the properties of glass fiber-cement-polyester composites are investigated. The specimens are prepared by hand lay-up technique. All the specimens are tested for tensile and flexural strength as per ASTM standards. Results showed that escalation in glass fiber wt.% improved the tensile strength (by 9% at 40 wt.% and 17% at 50 wt.%) and flexural strength (by 10% at 40 wt.% and 16.5% at 50 wt.%). Whereas an increase in cement weight percentage decreases tensile strength and increases flexural strength. The failure of the sample is due to glass fiber pull out and rupture of the matrix, under tensile load.

scholarly journals Natural Composite Reinforced by Lontar (Borassus flabellifer) Fiber: An Experimental Study on Open-Hole Tensile Strength

2017 ◽  
Vol 2017 ◽  
pp. 1-8
Author(s):  
Jefri Bale ◽  
Kristomus Boimau ◽  
Marselinus Nenobesi
Keyword(s):  
Tensile Strength ◽  
Unsaturated Polyester ◽  
Specific Area ◽  
Matrix Cracking ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Hole Configuration ◽  
The Matrix

A research has been conducted in the present study to investigate the effect of hole configuration on tensile strength of lontar fiber-reinforced composites. The lontar fiber-reinforced composites used in this study were produced by hand lay-up process. The lontar fiber-reinforced composites consist of short random fiber of 5 cm that contains 32% of nominal fiber volume as the reinforcement and unsaturated polyester as the matrix. The results show that the differences of hole configuration have an effect on tensile strength of lontar fiber-reinforced composites. It is found that the specific area of four-hole specimens experiences smaller strain propagation due to the redistributed stress and no stress passes through the hole. The damage of lontar fiber-reinforced composites with different hole configurations in tension is fairly straight and transverse to the loading axis, where the initial damage occurs in the form of matrix cracking, propagates into interfacial failure in form of delamination, and ultimately failed mainly due to the fiber breakage.

scholarly journals Experimental Investigation on Mechanical Properties of A/GFRP, B/GFRP and AB/GFRP Polymer Composites

2022 ◽  
Vol 58 (4) ◽  
pp. 28-36
Author(s):  
Velmurugan Natarajan ◽  
Ravi Samraj ◽  
Jayabalakrishnan Duraivelu ◽  
Prabhu Paulraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Polymer Composites ◽  
Fiber Reinforced ◽  
Gfrp Composites ◽  
Glass Fiber Reinforced ◽  
Structural Applications ◽  
Polyester Composites

This study aims to reveal the consequence of thickness reinforcement on Fiber Laminates (Polyester Resin, Glass Fiber, Aluminum, and Bentonite) and to see if it can enhance the mechanical properties and resistance of laminates. Glass fiber reinforced polymer composites have recently been used in automotive, aerospace, and structural applications where they will be safe for the application s unique shape. Hand layup was used to fabricate three different combinations, including Aluminium /Glass fiber reinforced polyester composites (A/GFRP), Bentonite/Glass fiber reinforced polyester composites (B/GFRP), and Aluminium&Bentonie/Glass fiber reinforced polyester composites (AB/GFRP). Results revealed that AB/GFRP had better tensile strength, flexural strength, and hardness than GFRP and A/GFRP. Under normal atmospheric conditions and after exposure to boiling water, hybrid Aluminium&Bentonite and glass fiber-reinforced nanocomposites have improved mechanical properties than other hybrid composites. After exposure to temperature, the flexural strength, tensile strength and stiffness of AB/GFRP Composites are 40 % higher than A/GFRP and 17.44% higher than B/GFRP Composites.

scholarly journals Preparation of Polymer Composites using Natural Fiber and their Physico-Mechanical Properties

1970 ◽  
Vol 45 (2) ◽  
pp. 117-122 ◽  
Author(s):  
Husna P Nur ◽  
M Akram Hossain ◽  
Shahin Sultana ◽  
M Mamun Mollah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
Polymer Composites ◽  
Natural Fiber ◽  
Banana Fiber ◽  
Elongation At Break ◽  
Reinforcing Material ◽  
Ldpe Composites

Use of natural fiber as reinforcing material is the latest invention of polymer science in order to get higher strength with lower weight composite materials having several applications. In this present investigation banana fiber, a natural fiber, is used as the reinforcing material. Low density polyethylene (LDPE)-banana fiber reinforced composites were prepared using both untreated and bleached (treated) banana fiber and LDPE with 7.5, 15, 22.5 and 30% weight content of fibers by using compression molding technique. Physico-mechanical properties (e.g. tensile strength, flexural strength, elongation at break, Young's modulus) of different types of prepared composites were characterized. From this study it is observed that all these values have augmented up to a definite percentage. The tensile strengths and flexural strengths of the composites increased up to 22.5% fiber addition then started to decrease gradually. Young moduli of the composites increased with the increase of fiber addition. Water absorption also increased with the weight of the fiber. Whereas elongation at break decreased with increasing fiber loading. Mechanical properties of bleached banana fiber-LDPE composites were slightly higher than the untreated banana fiber-LDPE composites. Compared to virgin molded LDPE both tensile and flexural strengths and Young moduli of these LDPE-banana fiber composites were significantly higher. All the variable properties like tensile strength, flexural strength, and water absorption capacity showed a very significant role in these polymer composites. Keywords: Banana fiber; LDPE; Composite; Tensile strength; Flexural strength DOI: 10.3329/bjsir.v45i2.5708Bangladesh J. Sci. Ind. Res. 45(2), 117-122, 2010

Study on Application of Modified Polyethylene in Preparation of Wood-Plastic Composites

2010 ◽  
Vol 150-151 ◽  
pp. 379-385
Author(s):  
Qun Lü ◽  
Qing Feng Zhang ◽  
Hai Ke Feng ◽  
Guo Qiao Lai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
High Density Polyethylene ◽  
Wood Flour ◽  
Wood Plastic Composites ◽  
Plastic Composites ◽  
The Matrix ◽  
The Impact

The wood-plastic composites (WPC) were prepared via compress molding by using the blends of high density polyethylene (HDPE) and modified polyethylene (MAPE) as the matrix and wood flour (WF) as filler. The effect of MAPE content in the matrix on the mechanical properties of the matrix and WPC was investigated. It was shown that the change of MAPE content in the matrix had no influence on the tensile strength of the matrix, but markedly reduced the impact strength of the matrix. Additionally, it had significant influence on the strength of WPC. When the content of wood flour and the content of the matrix remained fixed, with increasing the content of MAPE in the matrix, the tensile strength and the flexural strength of WPC tended to increase rapidly initially and then become steady. Moreover, with the increasing of MAPE concentration, the impact strength of WPC decreased when the low content of wood flour (30%) was filled, but increased at high wood flour loading (70%).

scholarly journals Investigation of Wood Flour Size, Aspect Ratios, and Injection Molding Temperature on Mechanical Properties of Wood Flour/Polyethylene Composites

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3406
Author(s):  
Mohammad E. Golmakani ◽  
Tomasz Wiczenbach ◽  
Mohammad Malikan ◽  
Reza Aliakbari ◽  
Victor A. Eremeyev
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Injection Molding ◽  
Polymer Composites ◽  
Impact Energy ◽  
Wood Flour ◽  
Impact Testing ◽  
Molding Temperature ◽  
Aspect Ratios

In the present research, wood flour reinforced polyethylene polymer composites with a coupling agent were prepared by injection molding. The effects of wood flour size, aspect ratios, and mold injection temperature on the composites’ mechanical properties were investigated. For the preparation of the polymer composites, five different formulations were created. The mechanical properties including tensile strength and the modulus, flexural strength and the modulus, and impact energy were measured. To investigate the changes in the properties resulting from different compositions, mechanical static and impact testing was performed. The obtained results indicate that by reducing the flour size, the tensile strength and modulus, flexural strength, and impact energy were reduced. In contrast, the flexural modulus increased. Furthermore, with the increment of injection molding temperature, the tensile strength and the modulus and the impact energy of the specimens were reduced. On the other hand, the flexural strength and the modulus increased. Thus, an optimized amount of injection molding temperature can provide improvements in the mechanical properties of the composite.

Influence of stacking sequence and orientation of the fabric on mechanical properties of twill Kenaf/Kevlar reinforced unsaturated polyester hybrid composites

2021 ◽  
pp. 152808372110199
Author(s):  
HT Sreenivas ◽  
N Krishnamurthy ◽  
MS Murali ◽  
GR Arpitha
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Natural Fiber ◽  
Hybrid Composites ◽  
Unsaturated Polyester ◽  
Synthetic Fiber ◽  
Stacking Sequence ◽  
The Matrix

The current study investigates on development of hybrid composite with Kenaf/Kevlar as reinforcement and unsaturated Polyester as the matrix considering stacking sequence, the orientation of fabric and twill 2x2 weave of the Kenaf fabric in particular. Five laminates (L1, L2, L3, L4, and L5) were developed by stacking the lamina's one over the other with the matrix and then cured in an autoclave. The laminates were subjected to experimental investigation to evaluate mechanical properties such as tensile strength, flexural strength, hardness, and impact strength. Results indicate that L5 shows good flexural strength and modulus, high hardness, and good impact strength, whereas L4 indicates the best tensile strength and tensile modulus. To summarize, the hybridization resulted in an average of 30% increased mechanical property for Laminate L5. The effect of stacking in L5 has a significant impact on the property of the composite. The results of the study were mainly focused on minimizing the use of synthetic fiber and replacing it with natural fiber. SEM analysis was performed on fractured surfaces of specimens which revealed that the failure of the laminated composite is due to poor interfacial bonding among fiber and matrix. Overall, the composite obtained from the combination of Kenaf and Kevlar fabrics had the best balance of properties finds appropriate application for car bumpers, fenders, boat hull, turbine blade etc.

scholarly journals Mechanical Characterization of Banana Fibre Reinforced Natural fibre Composite

2019 ◽  
Vol 9 (2) ◽  
pp. 2466-2471
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Fibre Composite ◽  
Weight Ratio ◽  
Natural Fibre ◽  
Natural Fibres ◽  
Reinforced Composites ◽  
Banana Fibre ◽  
Fibre Reinforced Composites

Fibre reinforced composites have been an essential concern in various fields, especially in the field of aerospace owing to its high strength to weight ratio, toughness, corrosion resistant and low cost. Natural fibre reinforced composites have produced better results in mechanical properties like impact, toughness and fatigue strengths when compared to synthetic fibre reinforced composites. Recently researches have been conducted on different varieties of natural fibres for use in plastics such as jute straw, wood, rice husk, wheat, barley etc. Natural fibres have also attracted the attention of researchers due to its availability, renewability, degradability and most importantly ecofriendly. In this work an attempt is made to improve the mechanical properties of the composite and also to enhance the compatibility of the fibres with the matrix. The composite is prepared by reinforcing banana fibres into unsaturated epoxy matrix using hand layup method. Mechanical properties such as tensile strength, flexural strength and hardness strengths are carried out on the specimens made by reinforcing with 5%, 10 % and 15 %concentration of banana fibre by weight. The results showed that the composite with 15% concentration of banana fibre produced higher tensile strength of 21.43 MPa, flexural strength of 0.895 kPa and Shroud hardness of 59.3.

Sign in / Sign up

Export Citation Format

Share Document