scholarly journals Acidic solution effects on no-fines concrete produced by using recycled concrete as coarse aggregate

2018 ◽  
Vol 162 ◽  
pp. 02002
Author(s):  
Ikbal Gorgis ◽  
Whab Faleh Abd ◽  
Shaker Al-Mishhadani
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Maximum Size ◽  
Recycled Concrete ◽  
Type I ◽  
Coarse Aggregates ◽  
Crushed Concrete ◽  
Compaction Factor ◽  
Single Size ◽  
Better Than

This paper investigates durability of no fine concrete containing demolished concrete as coarse aggregate after crushing to different sizes. Different no fine concrete mixes were considered using Portland cement type I with two types of coarse aggregates, crushed demolished concrete and crushed natural gravel were used with two ratios by weight (1:5 and 1:7) C/Agg. Graded aggregate and single size were used with a maximum size of 20 mm. W /C ratio was kept as 0.4 for all mixes and super-plasticizer was required to keep the same flow and compaction factor value for all mixes. Cube specimens with 150mm were cured and divided to two parts, the first part was exposed to 60 cycles of freezing- thawing; the second part of the sample was immersed in Nitric Acids solution with pH of 3.5 for (7, 28, 90 and 180 days) and then tested for compressive strength. The results indicated that it is possible to produce homogenous and workable mixes by using demolished crushed concrete as coarse aggregate. The compressive strength after cycles of freezing- thawing and immersing in Nitric acid (HNO3) at (7, 28, 90 and 180) days was decreased for samples made with crushed demolished concrete. Also it is found that the performance of concrete mixes containing graded coarse aggregate and 1:5 cement/aggregate ratios was better than other mixes.

IMPACT OF COARSE AGGREGATE ON COMPRESSIVE STRENGTH OF CONCRETE

2019 ◽  
Vol 16 (1) ◽  
pp. 52
Author(s):  
Jeriscot H. Quayson ◽  
Zakari Mustapha
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Average Density ◽  
Fine Aggregate ◽  
Coarse Aggregates ◽  
Crushed Granite ◽  
Compaction Factor ◽  
Compressive Strength Of Concrete ◽  
The Individual ◽  
The Impact

Over one-third of the volume of concrete is occupied by coarse aggregate and any changes in coarse aggregate type can affect its strength and fracture properties. The paper examined the impact of coarse aggregates on compressive strength of concrete. Slump and compaction factor tests were conducted on the mixture of quartzite and crushed granite course aggregates, and quarry dust (fine aggregate). Nominal mix (1:2:3) was adopted and mix compositions were calculated by absolute weight method. Twelve (12) cubes (150x150mm) of each type of coarse aggregate were cast for 7, 14, 21, and 28 days to determine their compressive strengths. Quartzite was found to have the highest average compressive strength of 24.48N/mm2 with an average density of 2160kg/m3 , while compressive strength of crushed granite was 22.01N/mm2 with an average density of 2300kg/m3 on the 28 day of testing. Concrete made from granite had the highest workability, while concrete made from quartzite aggregate had the highest compressive strength. Densities and compressive strengths of the individual aggregates accounted for the variation in strengths of the concrete, due to differences in properties and strengths. In conclusion, the effect of any type of coarse aggregate on the compressive strength of concrete will be known and also enable contractors to determine the type of aggregate to be selected for a particular work. Keywords: Compaction factor test; slump test; strength; workability.

Expermental Study on the Mixture Ratio and the Compressive Strength of Concrete with Recycle Crushed Brick Coarse Aggregate

2014 ◽  
Vol 584-586 ◽  
pp. 1362-1365 ◽  
Author(s):  
Qin Liu ◽  
Xiao Na Zhang
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Engineering Application ◽  
Recycled Concrete ◽  
Concrete Compressive Strength ◽  
Mixture Ratio ◽  
Coarse Aggregates ◽  
Compressive Performance ◽  
Compressive Strength Of Concrete ◽  
High Absorption

Considering the high absorption of water is a distinctive feature of recycled crushed bricks coarse aggregate, the mixture ratio text of recycled concrete using crushed bricks as coarse aggregate is carried out, and the compressive performance is studied.The resert indicate , the strength grade of recycled concrete which using bricks as coarse aggregate can reach C20 and C25, characterisitic value of cubic concrete compressive strength at the age of 28 days are 21.2MPa and 27.55MPa;Based on regression analysis of test data , the formulas which estimated the strength of recycled coarse aggregates concrete are given out. Calculated values are in agreement with the measurement values, which can provide a reference for engineering application.

Workability and Compressive Strength of Recycled Concrete Waste Aggregate Concrete

2015 ◽  
Vol 754-755 ◽  
pp. 417-420 ◽  
Author(s):  
Rashid Ali ◽  
Roszilah Hamid
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Construction Materials ◽  
Recycled Concrete ◽  
Compaction Factor ◽  
Design Values ◽  
Concrete Testing ◽  
Limiting Value ◽  
Percent Absorption

Concrete waste from construction site such as pile waste and tested concrete cubes waste is quite a problem for the contractor to dispose of. This waste is currently being buried or dumped illegally at a certain area, which lead to environmental pollution issue and waste of construction materials. In this study, concrete cubes waste from a concrete testing laboratory is crushed and recycled as natural coarse aggregate (NA) replacement (0% - control, 30% and 50% by mass) in grade 15, 25 and 40 concrete. The recycled concrete waste aggregate (RCWA) was tested for grading, specific gravity, percent absorption and impact and crushing (% crushed). For the fresh concrete mix, slump and compaction factor test were carried out. Concrete samples are wet cured and tested at 7 and 28 days for compressive strength. Results show that the workability of RCWA concrete reduce as the content of RCWA increase in the mix as the water absorption of RCWA is higher than the NA. The compressive strength of the RCWA concrete is acceptable at all RCWA replacement for grade 15 and 25 concrete with strengths higher than the design values of 15 and 25 MPa. For grade 40 concrete, the optimum RCWA replacement is at 30% and at 50% replacement, the compressive strength of the RCWA concrete is lower than the design value of 40 MPa. 50% replacement of NA with RCWA works well for grade 15 and 25 concrete, but for higher concrete grade (C40), the limiting value of replacement is 30%.

scholarly journals Effect of Fly Ash and Un-crushed Coarse Aggregates on Characteristics of SCC

2020 ◽  
Vol 6 (4) ◽  
pp. 693-701 ◽  
Author(s):  
Muneeb Ayoub Memon ◽  
Noor Ahmed Memon ◽  
Bashir Ahmed Memon
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Flow Time ◽  
Fresh Properties ◽  
Self Compacting Concrete ◽  
Coarse Aggregates ◽  
Slump Flow ◽  
Crushed Aggregate ◽  
Better Than

This research paper discusses the change in the workability and strength characteristics of Self Compacting Concrete (SCC) due to addition of fly-ash and use of un-crushed Coarse Aggregate (CA). Laboratory based experimental work was carried out by preparing 12 SCC mixtures among which six mixtures contained crushed aggregate and other six mixtures contained un-crushed coarse aggregate. A total of 550 kg/m3 binder content and fixed Water-Binder (W/B) ratio as 0.35 were used. Two mixtures were controlled by using Portland Cement (PC) and other ten mixtures contained PC and Fly Ash (FA). Slump flow time, slump flow diameter and J-ring height tests were conducted to study the fresh properties of SCC. Furthermore, compressive strength was calculated at 7, 14 and 28 days of curing. The outcomes indicated that the slump flow time, slump flow diameter and J-Ring height for all the mixes are within the limits specified by EFNARC guidelines. The compressive strength of SCCs depends upon dosage of fly ash. Compressive strength for SCCs with crushed CA was better than obtained in case of un-crushed CA. The maximum compressive-strengths were observed as 64.58 MPa and 58.05 MPa for SCC with crushed and un-crushed CA respectively.

scholarly journals Effect of Recycled Coarse Aggregate and Bagasse Ash on Two-Stage Concrete

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 556
Author(s):  
Muhammad Faisal Javed ◽  
Afaq Ahmad Durrani ◽  
Sardar Kashif Ur Rehman ◽  
Fahid Aslam ◽  
Hisham Alabduljabbar ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Construction Material ◽  
Strength Reduction ◽  
Recycled Aggregate ◽  
Two Stage ◽  
Conventional Concrete ◽  
Recycled Coarse Aggregate ◽  
Coarse Aggregates

Numerous research studies have been conducted to improve the weak properties of recycled aggregate as a construction material over the last few decades. In two-stage concrete (TSC), coarse aggregates are placed in formwork, and then grout is injected with high pressure to fill up the voids between the coarse aggregates. In this experimental research, TSC was made with 100% recycled coarse aggregate (RCA). Ten percent and twenty percent bagasse ash was used as a fractional substitution of cement along with the RCA. Conventional concrete with 100% natural coarse aggregate (NCA) and 100% RCA was made to determine compressive strength only. Compressive strength reduction in the TSC was 14.36% when 100% RCA was used. Tensile strength in the TSC decreased when 100% RCA was used. The increase in compressive strength was 8.47% when 20% bagasse ash was used compared to the TSC mix that had 100% RCA. The compressive strength of the TSC at 250 °C was also determined to find the reduction in strength at high temperature. Moreover, the compressive and tensile strength of the TSC that had RCA was improved by the addition of bagasse ash.

scholarly journals Carbonization Durability of Two Generations of Recycled Coarse Aggregate Concrete with Effect of Chloride Ion Corrosion

2020 ◽  
Vol 12 (24) ◽  
pp. 10544
Author(s):  
Chunhong Chen ◽  
Ronggui Liu ◽  
Pinghua Zhu ◽  
Hui Liu ◽  
Xinjie Wang
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Chloride Ion ◽  
Total Porosity ◽  
Recycled Concrete ◽  
Carbonation Depth ◽  
Aggregate Concrete ◽  
Recycled Coarse Aggregate ◽  
Carbonation Resistance ◽  
Two Generations

Carbonation durability is an important subject for recycled coarse aggregate concrete (RAC) applied to structural concrete. Extensive studies were carried out on the carbonation resistance of RAC under general environmental conditions, but limited researches investigated carbonation resistance when exposed to chloride ion corrosion, which is an essential aspect for reinforced concrete materials to be adopted in real-world applications. This paper presents a study on the carbonation durability of two generations of 100% RAC with the effect of chloride ion corrosion. The quality evolution of recycled concrete coarse aggregate (RCA) with the increasing recycling cycles was analyzed, and carbonation depth, compressive strength and the porosity of RAC were measured before and after chloride ion corrosion. The results show that the effect of chloride ion corrosion negatively affected the carbonation resistance of RAC, and the negative effect was more severe with the increasing recycling cycles of RCA. Chloride ion corrosion led to a decrease in compressive strength, while an increase in carbonation depth and the porosity of RAC. The equation of concrete total porosity and carbonation depth was established, which could effectively judge the deterioration of carbonation resistance of RAC.

Study on the Mechanical Properties and Frost Resistance of Recycled Concrete Prepared by Village Construction Wastes

2011 ◽  
Vol 418-420 ◽  
pp. 406-410
Author(s):  
Jun Liu ◽  
Yao Li ◽  
Dan Dan Hong ◽  
Yu Liu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Frost Resistance ◽  
Cement Mortar ◽  
Strength Loss ◽  
Recycled Concrete ◽  
Recycled Aggregate ◽  
Replacement Rate ◽  
Concrete Mechanical Properties ◽  
Better Than

Abstract. Recycled aggregate—rural building material wastes pretreated by cement mortar—are applied into concrete with different replacement rates: 0, 25%, 50%, 75%, and 100%. Results from measurements of compressive strength, cleavage tensile strength, mass loss after fast freeze-thaw cycles, and compressive strength loss indicate that a different recycled aggregate replacement rate certainly influences concrete mechanical properties and frost resistance. Recycled aggregate replacement rates less than 75% performs better than common concrete. Data from the 100% replacement rate is worse than that of rates less than 75% but still satisfy the general demands of GB standard on C30 concrete.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

scholarly journals Influence of Reduced Water Cement Ratio on Behaviour of Concrete Having Plastic Aggregate

2018 ◽  
Vol 4 (12) ◽  
pp. 2971 ◽  
Author(s):  
Saad Tayyab ◽  
Asad Ullah ◽  
Kamal Shah ◽  
Faial Mehmood ◽  
Akhtar Gul
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Stress Strain ◽  
Cement Ratio ◽  
Coarse Aggregates ◽  
Alternative Materials ◽  
Super Plasticizer ◽  
Strain Relationship ◽  
Natural Aggregates ◽  
Reduced Water

The production and use of plastic bottles is increasing tremendously with passing time. These plastic bottles become a problem when they are disposed as they are non-biodegradable. This means that the waste plastic, when dumped, does not decompose naturally and stays in the environment affecting the ecological system. The use of alternative aggregates like Plastic Coarse Aggregate (PCA) is a natural step in solving part of reduction of natural aggregates as well as to solve the issue discussed above. The researchers are trying from half a century to investigate the alternative materials to be replaced in concrete mixture in place of either aggregate or cement.  In this research, the concrete made from plastic waste as coarse aggregates were investigated for compressive strength and Stress-strain relationship. Plastic coarse aggregate have been replaced in place of natural coarse aggregate by different percentages with w/c 0.5, 0.4 and 0.3. The percentage replacement of plastic aggregate in place of mineral coarse aggregate was 25%, 30%, 35% and 40 %. Using Super-plasticizer Chemrite 520-BAS. OPC-53 grade cement was used. Total of forty five Cylinders were prepared based on different combination of Percentage of Plastic aggregate replaced and W/C as discussed above and checked for compressive strength and stress-strain relationship. The compressive strength increases by about 19.25% due to the decrease in W/C from 0.5 to 0.3 for plastic percentage addition of 40%.

Sign in / Sign up

Export Citation Format

Share Document