scholarly journals Titanium Ti6Al4V alloy reinforced by the addition of nano yttria stabilized zirconia fabricated by selective additive manufacturing: microstructure and mechanical investigations

2020 ◽  
Vol 321 ◽  
pp. 03018
Author(s):  
Amine HATTAL ◽  
Madjid DJEMAI ◽  
Jean Jacques FOUCHET ◽  
Thierry CHAUVEAU ◽  
Brigitte BACROIX ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Mass Density ◽  
Martensite Phase ◽  
Compression Tests ◽  
Stabilized Zirconia ◽  
Powder Mixtures ◽  
Size Refinement ◽  
Heat Treated ◽  
Elongation To Failure

Additive manufactured Ti6Al4V reinforced with nano yttria-zirconia (nYSZ) parts were fabricated using selective laser melting technology (SLM). The as-received Ti6Al4V powder and two powder mixtures of Ti6Al4V mixed with several nYSZ contents (1wt% and 2.5wt%) were prepared and then SLM processed. Parts were further subjected to a stress relief heat treatment. Besides, hot isostatic pressure (HIP) was used in order to eliminate residual porosities. The pycnometer-based technique was used to measure the mass density. XRD and EBSD analysis were performed to investigate the influence of nYSZ additions on the microstructure and subsequent mechanical properties via microhardness and compression tests. It was found that addition of nYSZ increases the density of the reinforced parts and produces a fine α martensite phase. Besides, the grain size was refined compared to that of heat treated Ti6Al4V. As a consequence, a significant increase in both the hardness and the compressive strength for the reinforced Ti6Al4V were obtained while the elongation to failure was kept. These improved mechanical properties are discussed in relation to the effect of nYSZ addition, which includes latice distortions and strengthening from grain size refinement and/or α formation.

Improvement of Mechanical Properties of 7475 Aluminium Alloy by the Combination of SPD Processing and Annealing

2011 ◽  
Vol 690 ◽  
pp. 311-314 ◽  
Author(s):  
Kinga Wawer ◽  
Małgorzata Lewandowska ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Aluminium Alloy ◽  
True Strain ◽  
Hydrostatic Extrusion ◽  
Synergic Effect ◽  
Size Refinement ◽  
Low Temperature Annealing ◽  
Heat Treated ◽  
Precipitate Strengthening

In the present study, SPD processing was combined with annealing in order to obtain synergic effect of grain size refinement and precipitate strengthening. Samples of 7475 alloy were solution heat treated, water quenched and then subjected to hydrostatic extrusion with a total true strain of about 4. Hydrostatic extrusion resulted in a significant grain refinement from 70 mm to about 70 nm. The samples were subsequently annealed at temperatures inducing the formation of nano-precipitates. The investigations of the structure and mechanical properties of the samples subjected to SPD and annealing revealed different precipitation path in micro- and nano-grained samples. Also, it was found that the combination of HE processing and low temperature annealing results in the formation of nano-precipitates in nano-grained structures which effectively strengthen nano-aluminium alloy.

scholarly journals Influence of Post Weld Heat Treatment on the Grain Size, and Mechanical Properties of the Alloy-800H Rotary Friction Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4366
Author(s):  
Saqib Anwar ◽  
Ateekh Ur Rehman ◽  
Yusuf Usmani ◽  
Ali M. Al-Samhan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Heat Affected Zone ◽  
Tensile Testing ◽  
Weld Zone ◽  
Alloy 800H ◽  
Weld Joints ◽  
Heat Treated ◽  
Friction Weld

This study evaluated the microstructure, grain size, and mechanical properties of the alloy 800H rotary friction welds in as-welded and post-weld heat-treated conditions. The standards for the alloy 800H not only specify the composition and mechanical properties but also the minimum grain sizes. This is because these alloys are mostly used in creep resisting applications. The dynamic recrystallization of the highly strained and plasticized material during friction welding resulted in the fine grain structure (20 ± 2 µm) in the weld zone. However, a small increase in grain size was observed in the heat-affected zone of the weldment with a slight decrease in hardness compared to the base metal. Post-weld solution heat treatment (PWHT) of the friction weld joints increased the grain size (42 ± 4 µm) in the weld zone. Both as-welded and post-weld solution heat-treated friction weld joints failed in the heat-affected zone during the room temperature tensile testing and showed a lower yield strength and ultimate tensile strength than the base metal. A fracture analysis of the failed tensile samples revealed ductile fracture features. However, in high-temperature tensile testing, post-weld solution heat-treated joints exhibited superior elongation and strength compared to the as-welded joints due to the increase in the grain size of the weld metal. It was demonstrated in this study that the minimum grain size requirement of the alloy 800H friction weld joints could be successfully met by PWHT with improved strength and elongation, especially at high temperatures.

Influence of Heat Treatment on Microstrudture and Mechanical Properties of AZ31B Magnesium Alloy Prepared by Solid-State Recycling

2012 ◽  
Vol 271-272 ◽  
pp. 17-20
Author(s):  
Shu Yan Wu ◽  
Ze Sheng Ji ◽  
Chun Ying Tian ◽  
Ming Zhong Wu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid State ◽  
Magnesium Alloy ◽  
Static Recrystallization ◽  
Annealing Treatment ◽  
Az31b Magnesium Alloy ◽  
Heat Treated ◽  
Elongation To Failure ◽  
Strength And Ductility

This work is to study the influence of heat treatment on microstrudture and mechanical properties of AZ31B magnesium alloy prepared by solid -state recycling. AZ31B magnesium alloy chips were recycled by hot extruding. Three different heat treatments were conducted for recycled alloy. Mechanical properties and microstructure of the recycled specimen and heat treated specimen were investigated. 300°C×2h annealing specimen exhibits finer grain due to static recrystallization, and microstructure of 400°C×2h annealing specimen becomes more coarse. 300°C×2h annealing treatment improves obviously strength and ductility of recycled alloy. Ultimate tensile strength of alloy decreases and elongation to failure increases after 400°C×2h annealing. Grain size, dislocation density and bonding of chips have an effect on the elongation of recycled materials. 190°C×8h ageing has no influence on microstructure and mechanical properties of recycled alloy.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

scholarly journals Mechanical Properties of Dye 3 Greenland Deep Ice Cores

1984 ◽  
Vol 5 ◽  
pp. 1-8 ◽  
Author(s):  
Nobuhiko Azuma ◽  
Akira Higashi
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Power Law ◽  
Ice Core ◽  
Ice Cores ◽  
Uniaxial Stress ◽  
Strain Rates ◽  
Compression Tests ◽  
Polycrystalline Ice ◽  
Relationship Of

Uniaxial compression tests were carried out with specimens cut from several deep ice cores obtained at Dye 3, Greenland, in 1980 and 1981. The power law relationship of = Αση was obtained between the uniaxial strain-rate and the uniaxial stress σ. In a range of strain-rates between 10−8 and 10−7 s−1, the value of the power n for samples with strong single maximum fabric was approximately 4, significantly larger than the value of 3 which has been generally accepted from experiments using artificial polycrystalline ice. A work-hardening effect was found in the ice-core samples taken from a depth of 1900 m, which had a smaller grain size than the others. Recrystallization occurred when the temperature of the specimen was raised during the test and this ultimately caused the formation of the so-called diamond pattern ice fabric.

Effect of post-heat treatment cooling on microstructure and mechanical properties of selective laser melting manufactured austenitic 316L stainless steel

2020 ◽  
Vol 26 (10) ◽  
pp. 1739-1749
Author(s):  
Saad Waqar ◽  
Jiangwei Liu ◽  
Qidong Sun ◽  
Kai Guo ◽  
Jie Sun
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
Content Type ◽  
Post Annealing ◽  
Cooling Conditions ◽  
Microstructure And Mechanical Properties ◽  
Heat Treated

Purpose This paper aims to investigate the influence of different post-annealing cooling conditions, i.e. furnace cooling (heat treatment (HT) 1 – slow cooling) and air cooling (HT 2 – fast cooling), on the microstructure and mechanical properties of selective laser melting (SLM) built austenitic 316L stainless steel (SS). Design/methodology/approach Three sets of 316L SS samples were fabricated using a machine standard scanning strategy. Each set consists of three tensile samples and a cubic sample for microstructural investigations. Two sets were subsequently subjected to annealing HT with different cooling conditions, i.e. HT 1 and HT 2, whereas one set was used in the as-built (AB) condition. The standard metallographic techniques of X-ray diffraction, scanning electron microscopy and electron back-scattered diffraction were used to investigate the microstructural variations induced by different cooling conditions. The resultant changes in mechanical properties were also investigated. Findings The phase change of SLM fabricated 316L was observed to be independent of the investigated cooling conditions and all samples consist of austenite phase only. Both HT 1 and HT 2 lead to dissolved characteristic melt pools of SLM. Noticeable increase in grain size of HT 1 and HT 2 samples was also observed. Compared with AB samples, the grain size of HT 1 and HT 2 was increased by 12.5% and 50%, respectively. A decreased hardness and strength, along with an increased ductility was also observed for HT 2 samples compared with HT 1 and AB samples. Originality/value From previous studies, it has been noticed that most investigations on HT of SLM fabricated 316L were mainly focused on the HT temperature or holding time. However, the post-HT cooling rate is also an equally important factor in deciding the microstructure and mechanical properties of heat-treated components. Therefore, this paper investigates the influence of different post-annealing cooling conditions on microstructure and mechanical properties of SLM fabricated 316L components. This study provides a foundation for considering the post-HT cooling rate as an influential parameter that controls the properties of heat-treated SLM components.

scholarly journals Nondestructive Evaluation of Thermal Aging in Al6061 Alloy by Measuring Acoustic Nonlinearity of Laser-Generated Surface Acoustic Waves

Metals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 38 ◽  
Author(s):  
Jihyun Jun ◽  
Hogeon Seo ◽  
Kyung-Young Jhang
Keyword(s):  
Mechanical Properties ◽  
Nondestructive Evaluation ◽  
Thermal Aging ◽  
Acoustic Waves ◽  
Surface Acoustic Waves ◽  
Tensile Tests ◽  
Acoustic Nonlinearity ◽  
Transmission Electron ◽  
Heat Treated ◽  
Elongation To Failure

The structures in high-temperature environments are prone to undergo hardening and embrittlement as a result of thermal aging; this can cause variations in their mechanical properties. Because these changes occur at the microstructural level, it is difficult to evaluate them through linear ultrasonic techniques. In this work, a surface acoustic wave (SAW) was used to measure and compare the acoustic nonlinearity and mechanical properties of Al6061 alloys heat-treated at 220 °C for different durations (0 min, 20 min, 40 min, 1 h, 2 h, 10 h, 100 h, 1000 h). The SAW was generated by a pulsed laser and then received by an interferometer. Moreover, the yield strength, ultimate strength, and elongation to failure were measured by tensile tests. The results demonstrate that the critical variations in the mechanical properties can be detected by monitoring the variation features in the acoustic nonlinearity. Transmission electron microscopy images were captured to observe the microstructural changes, which shows that the acoustic nonlinearity varied according to the change in the precipitation phase. This supports the acoustic nonlinearity measurement using the laser-generated SAW being an effective technique for the fully noncontact nondestructive evaluation of material degradations as well as changes in mechanical properties.

scholarly journals Influence of Vacuum Heat Treatments on Microstructure and Mechanical Properties of M35 High Speed Steel

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 643
Author(s):  
Chiara Soffritti ◽  
Annalisa Fortini ◽  
Ramona Sola ◽  
Elettra Fabbri ◽  
Mattia Merlin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Vickers Hardness ◽  
High Speed ◽  
High Speed Steel ◽  
Plane Strain Fracture Toughness ◽  
Secondary Carbides ◽  
Heat Treated ◽  
Strain Fracture

Towards the end of the last century, vacuum heat treatment of high speed steels was increasingly used in the fabrication of precision cutting tools. This study investigates the influence of vacuum heat treatments at different pressures of quenching gas on the microstructure and mechanical properties of taps made of M35 high speed steel. Taps were characterized by optical microscopy, scanning electron microscopy with energy dispersive spectroscopy, X-ray diffraction, apparent grain size and Vickers hardness measurements, and scratch tests. Failure analysis after tapping tests was also performed to determine the main fracture mechanisms. For all taps, the results showed that microstructures and the values of characteristics of secondary carbides, retained austenite, apparent grain size and Vickers hardness were comparable to previously reported ones for vacuum heat treated high speed steels. For taps vacuum heat treated at six bar, the highest plane strain fracture toughness was due to a higher content of finer small secondary carbides. In contrast, the lowest plane strain fracture toughness of taps vacuum heat treated at eight bar may be due to an excessive amount of finer small secondary carbides, which may provide a preferential path for crack propagation. Finally, the predominant fracture mechanism of taps was quasi-cleavage.

scholarly journals Friction Stir Processing of the Magnesium Alloy AZ61: Grain Size Refinement and Mechanical Properties

2012 ◽  
Vol 706-709 ◽  
pp. 1823-1828 ◽  
Author(s):  
J.A. del Valle ◽  
P. Rey ◽  
D. Gesto ◽  
D. Verdera ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Friction Stir Processing ◽  
Superplastic Forming ◽  
Important Change ◽  
Heat Extraction ◽  
Processing Temperature ◽  
Friction Stir ◽  
Size Refinement

The effect of friction stir processing (FSP), on the microstructure and mechanical properties of a magnesium alloy AZ61 has been analyzed. This is a widely used wrought magnesium alloy provided in the form of rolled and annealed sheets with a grain size of 45 μm. The FSP was performed with an adequate cooling device in order to increase the heat extraction and reduce the processing temperature. The final microstructure showed a noticeable grain size refinement down to values close to 1.8 μm and an important change in texture. The change in texture favors basal slip during tensile testing leading to an increase of ductility and a decrease in yield stress. The stability of the grain size and the creep behavior at high temperatures were investigated. The optimum conditions for superplastic forming were determined; however, the presence of a large amount of cavities precludes the achievement of high superplastic elongations. Additionally, these results are compared with those obtained by severe hot rolling.

Sign in / Sign up

Export Citation Format

Share Document