scholarly journals Impact response of various concretes at 2.8-second drop shaft

2021 ◽  
Vol 352 ◽  
pp. 00005
Author(s):  
Radoslav Sovják ◽  
Josef Fládr ◽  
Jiří Šťástka ◽  
Michal Frydrýn
Keyword(s):  
Reinforced Concrete ◽  
High Speed ◽  
High Performance ◽  
Experimental Testing ◽  
Maximal Velocity ◽  
Fibre Reinforced Concrete ◽  
Drop Shaft ◽  
Before And After ◽  
The Impact ◽  
High Performance Fibre

This paper presents experimental testing of various types of concrete under impact loading by using a 2.8-second drop shaft. The drop shaft is located in the Josef Underground Laboratory and allows dropping a projectile from 40 meters that results in a maximal velocity of 100 km/h. Three basic types of concrete were used in the framework of this study. This was normal strength concrete, fibre-reinforced concrete, and high-performance fibre-reinforced concrete. The slabs were constructed 1700 mm × 500 mm × 70 mm in size and the clear span of the impacted slab was 1500 mm. Damage of the slab was recorded and the velocity of the projectile was measured with the high-speed camera before and after the impact. It was demonstrated that high-performance fibre-reinforced concrete has a higher ability to absorb and dissipate the kinetic energy of the impact that their lower strength counterparts.

scholarly journals The comparison of projectile impact resistance of ultra-high-performance fibre-reinforced concrete with various aggregates

2021 ◽  
Vol 250 ◽  
pp. 06007
Author(s):  
Martina Drdlová ◽  
Martin Šperl
Keyword(s):  
Reinforced Concrete ◽  
High Speed ◽  
High Performance ◽  
Structural Integrity ◽  
Impact Load ◽  
Impact Resistance ◽  
Fibre Reinforced Concrete ◽  
Projectile Impact ◽  
The Impact ◽  
High Performance Fibre

In order to apply the ultra-high-performance fibre-reinforced concrete (UHPFRC) in the constructions of ballistic protective structures, the impact resistance of UHPFRC has been investigated experimentally by conducting the high-speed projectile penetration tests. 5 mixtures with basalt and corundum aggregates with various grain size have been prepared and subjected to the quasi-static and 7.62 x 54R B32 API projectile impact load using the striking velocity of 850 m/s. The influence of the strength, size and material of the aggregate on the projectile impact resistance represented by differential efficiency factor (DEF), structural integrity and area and height of impact crater has been evaluated. The superior projectile resistance of UHPFRC with corundum has been observed. Regarding the size of the aggregates, the incorporation of coarser aggregates brings better projectile impact resistance.

scholarly journals LABORATORY STUDY ON THE INFLUENCE OF CASTING ON PROPERTIES OF ULTRA-HIGH PERFORMANCE FIBRE REINFORCED CONCRETE (UHPFRC) SPECIMENS

2014 ◽  
Vol 20 (3) ◽  
pp. 380-379 ◽  
Author(s):  
Adam Zofka ◽  
Miglė Paliukaitė ◽  
Audrius Vaitkus ◽  
Dominika Maliszewska ◽  
Ramandeep Josen ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Fibre Orientation ◽  
Compact Tension ◽  
Fibre Reinforced Concrete ◽  
X Ray ◽  
Fracture Testing ◽  
Physical Changes ◽  
The Impact ◽  
High Performance Fibre

This paper presents a study on the effects of casting procedure and resulting fibre orientation on the properties of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC). To investigate the impact of fibre orientation in the UHPFRC specimens, three approaches were employed. First, densities were measured from the top, middle and bottom zones of the cylinders to observe physical changes as the function of cylinder height. Secondly, two engineering fracture tests were performed in both compression and tension, and a comparison of fracture energies was conducted between different cylinder zones. While previous studies have explored the influence of steel fibres on the UHPFRC performance, the Semi-Circular Bending (SCB) and Disc Compact Tension (DCT) experimental setups have not yet been used in the UHPFRC fracture testing. Lastly, samples from different zones were scanned using X-ray computer tomography (X-ray CT). Both visual and digital image analysis of the X-ray scans were conducted in order to observe fibre orientation pattern changes within different zones. Although density calculations showed insignificant differences between different zones, fracture testing exhibited significant differences through the testing process as well as through fracture energy computations. Furthermore, X-ray CT demonstrated considerable differences in spatial fibre orientation with respect to two uniquely defined angles.

Experimental procedure for determination of the energy dissipation capacity of ultra-high-performance fibre-reinforced concrete under localized impact loading

2019 ◽  
Vol 10 (2) ◽  
pp. 251-265 ◽  
Author(s):  
Petr Konrád ◽  
Radoslav Sovják
Keyword(s):  
Reinforced Concrete ◽  
Impact Loading ◽  
High Performance ◽  
Volume Fraction ◽  
Concrete Specimen ◽  
Basic Material ◽  
Fibre Reinforced Concrete ◽  
Significant Difference ◽  
The Impact ◽  
High Performance Fibre

Research presented in this article is aimed to investigate the ability of ultra-high-performance fibre-reinforced concrete to absorb and dissipate mechanical energy at elevated strain rate loading. Specimens made of ultra-high-performance fibre-reinforced concrete were subjected to the low-velocity impact using the new testing procedure where no fixed supports that hold the sample during the impact were applied. The fibre volume fraction of the ultra-high-performance fibre-reinforced concrete was set as the main test variable in the framework of this study and the volumetric fraction of fibres was ranging from 0.125% to 2%. A high-speed camera was used to measure velocities of the impactor and the ultra-high-performance fibre-reinforced concrete specimen before and after the impact. Consequently, the energy dissipated by the ultra-high-performance fibre-reinforced concrete specimen during the impact was calculated using a simple energy balance equation. To determine the basic material properties of ultra-high-performance fibre-reinforced concrete, quasi-static loading rate was applied and conventional methods were used. A significant difference between the values of dissipated energies for different loading rates and various fibre volumetric fractions was observed. It can be noted that the new procedure shows a reasonable approach for testing the fibre-reinforced cementitious composites under localized impact loading and is worthy of further optimization.

scholarly journals Ultra-high performance fibre-reinforced concrete under impact: experimental analysis of the mechanical response in extreme conditions and modelling using the Pontiroli, Rouquand and Mazars model

2017 ◽  
Vol 375 (2085) ◽  
pp. 20160173 ◽  
Author(s):  
Benjamin Erzar ◽  
Christophe Pontiroli ◽  
Eric Buzaud
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Mechanical Response ◽  
Experimental Testing ◽  
Tensile Fracture ◽  
Extreme Conditions ◽  
Fibre Reinforced Concrete ◽  
Steel Fibres ◽  
High Performance Fibre

To evaluate the vulnerability of ultra-high performance fibre-reinforced concrete (UHPFRC) infrastructure to rigid projectile penetration, over the last few years CEA-Gramat has led an experimental and numerical research programme in collaboration with French universities. During the penetration process, concrete is subjected to extreme conditions of pressure and strain rate. Plasticity mechanisms as well as dynamic tensile and/or shear damage are activated during the tunnelling phase and the cratering of the concrete target. Each mechanism has been investigated independently at the laboratory scale and the role of steel fibres especially has been analysed to understand their influence on the macroscopic behaviour. To extend the experimental results to the structural scale, penetration tests on UHPFRC slabs have been conducted by CEA-Gramat. The analysis of this dataset combined with material characterization experiments allows the role of steel fibres to be identified in the different plasticity and damage mechanisms occurring during penetration. In parallel, some improvements have been introduced into the concrete model developed by Pontiroli, Rouquand and Mazars (PRM model), especially to take into account the contribution made by the fibres in the tensile fracture process. After a primary phase of validation, the capabilities of the PRM model are illustrated by performing numerical simulations of projectile penetration into UHPFRC concrete structures. This article is part of the themed issue ‘Experimental testing and modelling of brittle materials at high strain rates’.

scholarly journals Behaviour of UHPFRCs in compression under high stress-rates

2018 ◽  
Vol 183 ◽  
pp. 02005
Author(s):  
Ezio Cadoni ◽  
Matteo Dotta ◽  
Daniele Forni
Keyword(s):  
Reinforced Concrete ◽  
Mechanical Behaviour ◽  
High Performance ◽  
High Stress ◽  
Slight Reduction ◽  
Fibre Reinforcement ◽  
Fibre Reinforced Concrete ◽  
Dynamic Event ◽  
The Matrix ◽  
High Performance Fibre

The paper presents the results obtained on cylindrical Ultra High Performance Fibre Reinforced Concrete specimens with diameter of 30mm and a height of 60mm under compression at high stress rate (1.7–2.3 TPa/s). Four different percentages of fibre reinforcement are considered (1, 2, 3, and 4% fibre content) and compared with the results of the matrix (UHPC). A slight reduction of the strength and fracture time with the introduction of fibres is observed. The experimental results are analysed and discussed with the intent to better understand the mechanical behaviour of UHPFRC materials in case of dynamic event under service loading conditions.

The new Pinel Bridge in Rouen, the fifth French road bridge using ultra high performance fibre-reinforced concrete components

2008 ◽  
Vol 17 (11) ◽  
pp. 316-317
Author(s):  
Daniel de MATTEIS ◽  
Pierre MARCHAND ◽  
Aude PETEL ◽  
Thierry THIBAUX ◽  
Nicolas FABRY ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Fibre Reinforced Concrete ◽  
High Performance Fibre

scholarly journals The Effect of the Morphology of Coarse Aggregate on the Properties of Self-Compacting High-Performance Fibre-Reinforced Concrete

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1372 ◽  
Author(s):  
Krzysztof Ostrowski ◽  
Łukasz Sadowski ◽  
Damian Stefaniuk ◽  
Daniel Wałach ◽  
Tomasz Gawenda ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Physical And Mechanical Properties ◽  
Concrete Mixture ◽  
Rheological Parameters ◽  
Transverse Strain ◽  
Fibre Reinforced Concrete ◽  
High Performance Fibre

When understanding the effect of the morphology of coarse aggregate on the properties of a fresh concrete mixture, the strength and deformability of self-compacting high-performance fibre-reinforced concrete (SCHPFRC) can be seen to be critical for its performance. In this research, regular and irregular grains were separated from granite coarse aggregate. The morphology of these grains was described while using digital image analysis. As a result, the aspect ratio, roundness and area ratio were determined in order to better understand this phenomenon. Then, the principal rheological, physical, and mechanical properties of SCHPFRC were determined. The obtained results indicated that the morphology of the grains of coarse aggregate has an impact on the strength and stiffness properties of SCHPFRC. Moreover, significant differences in the transverse strain of concretes were observed. The morphology of the coarse aggregate also has an impact on the rheological parameters of a fresh concrete mixture. To better understand this phenomenon, the hypothesized mechanism of the formation of SCHPFRC caused by different morphology of coarse aggregate was proposed at the end of the article.

Sign in / Sign up

Export Citation Format

Share Document