Low voltage pulse injection test of a single-stage 1 MV prototype induction voltage adder cell

2014 ◽  
Vol 85 (8) ◽  
pp. 083506 ◽  
Author(s):  
Hao Wei ◽  
Fengju Sun ◽  
Tianxue Liang ◽  
Jiahui Yin ◽  
Tengfei Dang ◽  
...  
Author(s):  
Nur Adilah Abd Rahman ◽  
Muhammad Mahadi Abdul Jamil ◽  
Mohamad Nazib Adon ◽  
Ahmad Basri Zainal ◽  
Farideh Javid ◽  
...  

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2899 ◽  
Author(s):  
Alexis B. Rey-Boué ◽  
N. F. Guerrero-Rodríguez ◽  
Johannes Stöckl ◽  
Thomas I. Strasser

This article deals with the vector control in dq axes of a three-phase grid-connected photovoltaic system with single-stage topology and low-voltage-ride-through capability. The photovoltaic generator is built using an array of several series-parallel Suntech PV modules and is modeled as a Lookup Table (two-dimensional; 2-D). The requirements adopted when grid voltage sags occur are based in both the IEC 61400-21 European normative and the allowed amount of reactive power to be delivered according to the Spanish grid code, which avoids the disconnection of the inverter under grid faults by a limitation in the magnitude of the three-phase output inverter currents. For this, the calculation of the positive- and negative-sequences of the grid voltages is made and a conventional three-phase Phase-Locked Loop is used for the inverter-grid synchronization, allowing the control of the active and reactive powers solely with the dq components of the inverter currents. A detailed enhanced flowchart of the control algorithm with low-voltage-ride-through capability is presented and several simulations and experiments using Matlab/SIMULINK and the Controller Hardware-in-the-Loop simulation technique, respectively, are run for several types of one- and three-phase voltage sags in order to validate its behavior.


2019 ◽  
Vol 66 (11) ◽  
pp. 8463-8473 ◽  
Author(s):  
Yijie Wang ◽  
Fang Li ◽  
Yuping Qiu ◽  
Shanshan Gao ◽  
Yueshi Guan ◽  
...  

2012 ◽  
Vol 302 (4) ◽  
pp. R446-R453 ◽  
Author(s):  
Pernille Hojman ◽  
Camilla Brolin ◽  
Hanne Gissel

Cell membrane permeabilization by electric pulses (electropermeabilization), results in free exchange of ions across the cell membrane. The role of electrotransfer-mediated Ca2+-influx on muscle signaling pathways involved in degeneration (β-actin and MurF), inflammation (IL-6 and TNF-α), and regeneration (MyoD1, myogenin, and Myf5) was investigated, using pulse parameters of both electrochemotherapy (8 HV) and DNA delivery (HVLV). Three pulsing conditions were used: 8 high-voltage pulses (8 HV), resulting in large permeabilization and ion flux, and a combination of one high-voltage pulse and one low-voltage pulse (HVLV), either alone or in combination with injection of DNA. Mice and rats were anesthetized before pulsing. At the times given, animals were killed, and intact tibialis cranialis muscles were excised for analysis. Uptake of Ca2+ was assessed using 45Ca as a tracer. Using gene expression analyses and histology, we showed a clear association between Ca2+ influx and muscular response. Moderate Ca2+ influx induced by HVLV pulses results in activation of pathways involved in immediate repair and hypertrophy. This response could be attenuated by intramuscular injection of EGTA reducing Ca2+ influx. Larger Ca2+ influx as induced by 8-HV pulses leads to muscle damage and muscle fiber regeneration through recruitment of satellite cells. The extent of Ca2+ influx determines the muscular response to electrotransfer and, thus, the success of a given application. In the case of electrochemotherapy, in which the objective is cell death, a large influx of Ca2+ may be beneficial, whereas for DNA electrotransfer, muscle recovery should occur without myofiber loss to ensure preservation of plasmid DNA.


Sign in / Sign up

Export Citation Format

Share Document