Study on deformation and stress evolution law of surrounding rock under repeated mining in close coal seam

2020 ◽  
pp. 1-19
Author(s):  
Qiang Zhang ◽  
Jiaqi Wang ◽  
Yuming Guo ◽  
Yang Chen ◽  
Qiang Sun
Keyword(s):  
Coal Seam ◽  
Surrounding Rock ◽  
Stress Evolution ◽  
Evolution Law

scholarly journals Surrounding rock deformation and stress evolution in pre-driven longwall recovery rooms at the end of mining stage

2019 ◽  
Vol 6 (4) ◽  
pp. 536-546 ◽  
Author(s):  
Bonan Wang ◽  
Faning Dang ◽  
Wei Chao ◽  
Yanping Miao ◽  
Jun Li ◽  
...  
Keyword(s):  
Coal Seam ◽  
Coal Mine ◽  
Recovery Room ◽  
Coal Pillar ◽  
Main Roof ◽  
Surrounding Rock ◽  
Rock Deformation ◽  
Stress Evolution ◽  
The Face ◽  
Surrounding Rock Deformation

Abstract Two case studies were conducted in the Shennan mining area of Shaanxi Province, China to evaluate the surrounding rock deformation and stress evolution in pre-driven longwall recovery rooms. These studies mainly monitored the surrounding rock deformation and coal pillar stress in the recovery rooms of the N1206 panel of 2−2 coal seam at Ningtiaota Coal Mine and the 15205 panel of 5−2 coal seam at Hongliulin Coal Mine. The monitoring results showed that the surrounding rock deformation of the main recovery room and the coal pillar stress in the N1206 and 15205 panels began to increase significantly when the face was 36 m and 42 m away from the terminal line, respectively. After the face entered the main recovery room, the maximum roof-to-floor convergence in the N1206 and 15205 panels was 348.03 mm and 771.24 mm, respectively, and the coal pillar stresses increased more than 5 MPa and 7 MPa, respectively. In addition, analysis of the periodic weighting data showed that the main roof break position of the N1206 and 15205 panels after the longwall face entered the main recovery room was − 3.8 m and − 8.2 m, respectively. This research shows that when the main roof breaks above the coal pillar, the surrounding rock deformation of the main recovery room and the coal pillar stress increase sharply. The last weighting is the key factor affecting the stability of the main recovery room and the coal pillar; main roof breaks at disadvantageous positions are the main cause of the support crushing accidents.

scholarly journals Dynamic Evolution Law of Overburden Rock in Shallow-Buried Super-High Fully Mechanized Working Face and Determination of Support Strength

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Yingjie Liu ◽  
Haijun Wang ◽  
Qingjie Qi ◽  
Anhu Wang ◽  
Youxin Zhao
Keyword(s):  
Coal Seam ◽  
Principal Stress ◽  
Maximum Principal Stress ◽  
Stress Recovery ◽  
Stress Evolution ◽  
Evolution Law ◽  
Working Face ◽  
Minimum Principal Stress ◽  
Coal Wall ◽  
Mining Face

The objective of this study was to reveal the law of overburden movement and stress evolution during the mining of super-high fully mechanized mining faces. Based on the 12401 fully mechanized mining face of Shangwan Coal Mine in Shendong, this study conducted research and analysis using the methods of similarity simulation experiment, numerical simulation, and field measurement. The results showed that the maximum and minimum principal stresses in the coal seam in front of the working face are concentrated with the advance of the working face. The degree of stress concentration increases with the increase in the advancing range, and the concentration degree of the maximum principal stress and the change gradient is greater than that of the minimum principal stress. But the range of the peak lead coal wall is lower than that of the minimum principal stress of the peak lead coal wall. The phenomenon of stress recovery exists in the goaf. With the increase in the advancing range of the working face, the degree of stress recovery gradually increases, and the degree of maximum principal stress recovery is higher than that of the minimum principal stress recovery. The large fractures observed near the working face are closely related to the underground pressure, relatively large fractures appear on the surface, and the fractures become narrower near the two pathways. Only caving and fissure zones exist in the thin bedrock overburden, and the bending subsidence zone changes with the bedrock thickness. The support strength of the hydraulic support should not be less than 1.47 MPa. This research on the overburden movement and stress evolution law of a super-high fully mechanized mining face can provide theoretical guidance for the exploitation and utilization of extrathick coal seam resources. It has broad engineering prospects.

scholarly journals Cooperative Control Mechanism of Long Flexible Bolts and Blasting Pressure Relief in Hard Roof Roadways of Extra-Thick Coal Seams: A Case Study

2021 ◽  
Vol 11 (9) ◽  
pp. 4125
Author(s):  
Zhe Xiang ◽  
Nong Zhang ◽  
Zhengzheng Xie ◽  
Feng Guo ◽  
Chenghao Zhang
Keyword(s):  
Coal Seam ◽  
Cooperative Control ◽  
Field Tests ◽  
Surrounding Rock ◽  
Deep Hole ◽  
Coal Seams ◽  
Thick Coal Seam ◽  
Structure Damage ◽  
Hard Roof

The higher strength of a hard roof leads to higher coal pressure during coal mining, especially under extra-thick coal seam conditions. This study addresses the hard roof control problem for extra-thick coal seams using the air return roadway 4106 (AR 4106) of the Wenjiapo Coal Mine as a case study. A new surrounding rock control strategy is proposed, which mainly includes 44 m deep-hole pre-splitting blasting for stress releasing and flexible 4-m-long bolt for roof supporting. Based on the new support scheme, field tests were performed. The results show that roadway support failure in traditional scenarios is caused by insufficient bolt length and extensive rotary subsidence of the long cantilever beam of the hard roof. In the new proposed scheme, flexible 4-m-long bolts are shown to effectively restrain the initial expansion deformation of the top coal. The deflection of the rock beam anchored by the roof foundation are improved. Deep-hole pre-splitting blasting effectively reduces the cantilever distance of the “block B” of the voussoir beam structure. The stress environment of the roadway surrounding rock is optimized and anchorage structure damage is inhibited. The results provide insights regarding the safe control of roadway roofs under extra-thick coal seam conditions.

scholarly journals Comprehensive technical support for safe mining in ultra-close coal seams: A case study

2021 ◽  
pp. 014459872110093
Author(s):  
Wei Zhang ◽  
Jiawei Guo ◽  
Kaidi Xie ◽  
Jinming Wang ◽  
Liang Chen ◽  
...  
Keyword(s):  
Coal Seam ◽  
Technical Support ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Deformation Control ◽  
Hard Roof ◽  
Working Face ◽  
Close Coal Seams ◽  
Safe Mining

In order to mine the coal seam under super-thick hard roof, improve the utilization rate of resources and prolong the remaining service life of the mine, a case study of the Gaozhuang Coal Mine in the Zaozhuang Mining Area has been performed in this paper. Based on the specific mining geological conditions of ultra-close coal seams (#3up and #3low coal seams), their joint systematic analysis has been performed, with the focus made in the following three aspects: (i) prevention of rock burst under super-thick hard roof, (ii) deformation control of surrounding rock of roadways in the lower coal seam, and (iii) fire prevention in the goaf of working face. Given the strong bursting tendency observed in upper coal seam and lower coal seam, the technology of preventing rock burst under super-thick hard roof was proposed, which involved setting of narrow section coal pillars to protect roadways and interleaving layout of working faces. The specific supporting scheme of surrounding rock of roadways in the #3low1101 working face was determined, and the grouting reinforcement method of local fractured zones through Marithan was further proposed, to ensure the deformation control of surrounding rock of roadways in lower coal seams. The proposed fire prevention technology envisaged goaf grouting and spraying to plug leaks, which reduced the hazard of spontaneous combustion of residual coals in mined ultra-close coal seams. The technical and economic improvements with a direct economic benefit of 5.55 million yuan were achieved by the application of the proposed comprehensive technical support. The research results obtained provide a theoretical guidance and technical support of safe mining strategies of close coal seams in other mining areas.

Reasonable Entry Layout of Lower Seam in Multi-Seam Mining Based on Numerical Simulation

2013 ◽  
Vol 295-298 ◽  
pp. 2980-2984
Author(s):  
Xiang Qian Wang ◽  
Da Fa Yin ◽  
Zhao Ning Gao ◽  
Qi Feng Zhao
Keyword(s):  
Numerical Simulation ◽  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mine ◽  
Abutment Pressure ◽  
Surrounding Rock ◽  
Geological Conditions ◽  
Seam Mining

Based on the geological conditions of 6# coal seam and 8# coal seam in Xieqiao Coal Mine, to determine reasonable entry layout of lower seam in multi-seam mining, alternate internal entry layout, alternate exterior entry layout and overlapping entry layout were put forward and simulated by FLAC3D. Then stress distribution and displacement characteristics of surrounding rock were analyzed in the three ways of entry layout, leading to the conclusion that alternate internal entry layout is a better choice for multi-seam mining, for which makes the entry located in stress reduce zone and reduces the influence of abutment pressure of upper coal seam mining to a certain extent,. And the mining practice of Xieqiao Coal Mine tested the results, which will offer a beneficial reference for entry layout with similar geological conditions in multi-seam mining.

scholarly journals Surrounding Rock Movement of Steeply Dipping Coal Seam Using Backfill Mining

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Wenyu Lv ◽  
Kai Guo ◽  
Jianhao Yu ◽  
Xufeng Du ◽  
Kun Feng
Keyword(s):  
Numerical Simulation ◽  
Coal Seam ◽  
Surrounding Rock ◽  
Maximum Deflection ◽  
Coal Seams ◽  
Physical Similarity ◽  
Working Face ◽  
Rock Structure ◽  
Backfill Mining ◽  
The Stability

The movement of the overlying strata in steeply dipping coal seams is complex, and the deformation of roof rock beam is obvious. In general, the backfill mining method can improve the stability of the surrounding rock effectively. In this study, the 645 working face of the tested mine is used as a prototype to establish the mechanical model of the inclined roof beam using the sloping flexible shield support backfilling method in a steeply dipping coal seam, and the deflection equation is derived to obtain the roof damage structure and the maximum deflection position of the roof beam. Finally, numerical simulation and physical similarity simulation experiments are carried out to study the stability of the surrounding rock structure under backfilling mining in steeply dipping coal seams. The results show the following: (1) With the support of the gangue filling body, the inclined roof beam has smaller roof subsidence, and the maximum deflection position moves to the upper part of working face. (2) With the increase of the stope height, the stress and displacement field of the surrounding rock using the backfilling method show an asymmetrical distribution, the movement, deformation, and failure increase slowly, and the increase of the strain is relatively stable. Compared with the caving method, the range and degree of the surrounding rock disturbed by the mining stress are lower. The results of numerical simulation and physical similarity simulation experiment are generally consistent with the theoretically derived results. Overall, this study can provide theoretical basis for the safe and efficient production of steeply dipping coal seams.

scholarly journals Key Parameters of Roof Cutting of Gob-Side Entry Retaining in a Deep Inclined Thick Coal Seam with Hard Roof

Energies ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 934 ◽  
Author(s):  
Jinzhu Hu ◽  
Manchao He ◽  
Jiong Wang ◽  
Zimin Ma ◽  
Yajun Wang ◽  
...  
Keyword(s):  
Numerical Model ◽  
Coal Seam ◽  
Economic Benefits ◽  
Surrounding Rock ◽  
Thick Coal Seam ◽  
Hard Roof ◽  
Coal Recovery ◽  
Rock Structure ◽  
Different Depths ◽  
Dip Angle

Gob-side entry retaining by roof cutting (GERRC) employed in a deep inclined thick coal seam (DITCS) can not only increase economic benefits and coal recovery, but also optimize surrounding rock structure. In accordance with the principles of GERRC, the technology of GERRC in DITCS is introduced and a roof-cutting mechanical model of GERRC is proposed to determine the key parameters of the depth and angle of RC. The results show that the greater the RC angle, the easier the caving of the goaf roof, but the length of cantilever beam increases. The depth of RC should account for the dip angle of the coal seam when the angle is above 20°. Increasing the coal seam dip angle could reduce the volume of rock falling of the goaf roof, but increase the filling height of the upper gangue to slide down. According to numerical model analysis of the stress and displacement of surrounding rock at different depths and angles of RC, when the depth of RC increased from 9 m to 13 m, the distance between the stress concentration zone and the coal side is increased. When the angle of RC increased from 0° to 20°, the value of roof separation is decreased. GERRC was applied in a DITCS with 11 m depth and 20° RC angle, and the field-measured data verified the conclusions of the numerical model.

Sign in / Sign up

Export Citation Format

Share Document