scholarly journals Activated Carbons (AC) Prepared by Direct CO2 Activation of Parsea Americana seeds Biomass for Supercapacitor Electrodes

2021 ◽  
Vol 2049 (1) ◽  
pp. 012067
Author(s):  
Rakhmawati Farma ◽  
Ramadani Putri Anakis ◽  
Irma Apriyani
Keyword(s):  
Activated Carbons ◽  
Chemical Activation ◽  
Physical Activation ◽  
Co2 Activation ◽  
X Ray Diffraction ◽  
Activation Temperature ◽  
X Ray ◽  
Cyclic Voltametry ◽  
Scanning Electron

Abstract Biomass converted into activated carbon (AC) by using physical activation method can form micro-meso pore structure and maintain the interconnected natural pore network of biomass. AC is prepared from the biomass of Parsea Americana seeds (PAS) through a process of pre-carbonization, chemical activation, carbonization and physical activation which is activated at temperatures of 700°C, 800°C, and 900°C. Characterization of physical properties of AC electrodes consisted of X-ray diffraction, Scanning Electron Microscope-Energy Dispersive X-ray and characterization of electrochemical properties of supercapacitor cells using Cyclic Voltametry. The results showed that the microstructure of the AC electrode has a semicrystalline structure characterized by the presence of two sloping peaks at an angle of 2θ around 24° and 44° which corresponded to the hkl (002) and (100) planes, where the lowest Lc value was produced by the PAS-900 sample. The PAS-900 sample had aggregates or lumps with smaller size in small amounts in the presence of micro-mesopores and had the highest carbon content of 94.50% with the highest capacitance value of 203.12 F/g. The temperature of 900°C is the best activation temperature in the process of manufacture AC electrodes from Parsea Americana seeds biomass for supercapacitor cell applications.

scholarly journals Characterization of Active Carbon Prepared from Coconuts Shells using FTIR, XRD and SEM Techniques

2018 ◽  
Vol 7 (1) ◽  
pp. 33 ◽  
Author(s):  
Andi Ikhtiar Bakti ◽  
Paulus Lobo Gareso
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
X Ray Diffraction ◽  
Activation Temperature ◽  
X Ray ◽  
Carbon And Graphite ◽  
Diffraction Peaks ◽  
Coconut Shells ◽  
Physical And Chemical

Activated carbon is produced from coconut shells through physical and chemical activation. With pyrolysis method, the optimum activation temperature for physics activation is 600oC, and for chemical, activation is to soak it in activator ZnCl2 10% and Na2Ca3 10%. Activated carbon was analyzed by Fourier Transformation Infrared (FTIR) and X-ray Diffraction (XRD) methods. The FTIR result showed that the coconut shells succeeds in becoming carbon. The XRD results confirm the existence of several phases of crystals like graphite around the peaks of 36o and 44o, there are two wide diffraction peaks and can be interconnected with carbon and graphite content. The SEM result showed that the carbonization of pyrolysis and activation processes created porosity and a large surface area for absorption.Keywords: activated carbon, coconut shell, FTIR, SEM, XRD

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

Characterization of hydrofluoric acid treated Y–Ba–Cu–O oxides

1989 ◽  
Vol 4 (6) ◽  
pp. 1320-1325 ◽  
Author(s):  
Q. X. Jia ◽  
W. A. Anderson
Keyword(s):  
Hydrofluoric Acid ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Surface Passivation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zero Resistance ◽  
Reaction With Water ◽  
Scanning Electron

Effects of hydrofluoric acid (HF) treatment on the properties of Y–Ba–Cu–O oxides were investigated. No obvious etching of bulk Y–Ba–Cu–O and no degradation of zero resistance temperature were observed even though the oxides were placed into 49% HF solution for up to 20 h. Surface passivation of Y–Ba–Cu–O due to HF immersion was verified by subsequent immersion of Y–Ba–Cu–O in water. A thin layer of amorphous fluoride formed on the surface of the Y–Ba–Cu–O during HF treatment, which limited further reaction between Y–Ba–Cu–O and HF, and later reaction with water. Thin film Y–Ba–Cu–O was passivated by HF vapors and showed no degradation in Tc-zero after 30 min immersion in water. The properties of the surface layer of Y–Ba–Cu–O oxide after HF treatment are reported from Auger electron spectroscopy, x-ray diffraction, and scanning electron microscopy studies.

Isolation and characterization of lignocellulosic fiber from jute bast by the organic solvent degumming system: an alkali-free method

2021 ◽  
pp. 004051752110154
Author(s):  
Zhihui Qin ◽  
Shuyuan Zhao ◽  
Liu Liu ◽  
Zhaohe Shi ◽  
Longdi Cheng ◽  
...  
Keyword(s):  
National Standards ◽  
X Ray Diffraction ◽  
High Concentration ◽  
X Ray ◽  
Lignocellulosic Fibers ◽  
Lignocellulosic Fiber ◽  
Isolation And Characterization ◽  
Alkali Consumption ◽  
Scanning Electron

Degumming is the dominant method for insolating lignocellulosic fibers in textile applications. Traditional alkaline degumming (TAL), as a common method, requires a high-concentration alkali and has been a severe challenge to the environment. In the research reported here, the possibility of innovative jute degumming by organic solvents 1-2 propylene glycol and a combination of additive green oxygen (GO-OS) was studied. The results revealed that fibers could be extracted by this system (under condition of 0.9% GO-OS, 180°C, 120 min), and obtained fibers with higher breaking tenacity (7.1 cN/dtex), yield (65.7%), breaking elongation (2.87%) and residual gum (11.7%), which all meet the requirement of the relevant Chinese Textile National Standards. Notably, the required reaction time (120 min) of the GO-OS system was 180 min shorter than that of the TAL method. Furthermore, the modifications introduced by the degumming effect on physicochemical aspects were characterized and confirmed by Fourier transform infrared spectroscopy, scanning electron microscopy and X-ray diffraction. This study provides a promising degumming method for separating jute lignocellulose without acid and alkali consumption.

Characterization of a coating for radioprotection, by X-ray diffraction, scanning electron microscopy, and dispersive energy spectroscopy

2022 ◽  
Vol 321 ◽  
pp. 126326
Author(s):  
Gladis Aparecida Galindo Reisemberger de Souza ◽  
Ramón Sigifredo Cortés Paredes ◽  
Frieda Saicla Barros ◽  
Gustavo Bavaresco Sucharski ◽  
Sebastião Ribeiro Junior ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

scholarly journals Investigations of M3Al8O15:Eu3+,Dy3+ (M = Ba, Ca, Mg) phosphors

2016 ◽  
Vol 34 (2) ◽  
pp. 412-417
Author(s):  
Esra Öztürk
Keyword(s):  
Electron Microscopy ◽  
Solid State Reaction Method ◽  
Morphological Characterization ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Three Samples ◽  
Scanning Electron ◽  
The Eu

AbstractIn this work, aluminate type phosphorescence materials were synthesized via the solid state reaction method and the photoluminescence (PL) properties, including excitation and emission bands, were investigated considering the effect of trace amounts of activator (Eu3+) and co-activator (Dy3+). The estimated thermal behavior of the samples at certain temperatures (> 1000 °C) during heat treatment was characterized by differential thermal analysis (DTA) and thermogravimetry (TG). The possible phase formation was characterized by X-ray diffraction (XRD). The morphological characterization of the samples was performed by scanning electron microscopy (SEM). The PL analysis of three samples showed maximum emission bands at around 610 nm, and additionally near 589 nm, 648 nm and 695 nm. The bands were attributed to typical transitions of the Eu3+ ions.

Rapid Synthesis and Characterization of CuInS2 Prepared Using Microwave-Assisted Heating

2015 ◽  
Vol 775 ◽  
pp. 143-146
Author(s):  
Ming Kwen Tsai ◽  
Yueh Chien Lee ◽  
Chia Chih Huang ◽  
Sheng Yao Hu ◽  
Kwong Kau Tiong ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Rapid Synthesis ◽  
X Ray ◽  
Sem Image ◽  
Microwave Assisted ◽  
Calcination Treatment ◽  
Scanning Electron

In this work, the CuInS2 nanoparticles are successfully synthesized by microwave-assisted heating technique and further calcined at 400 °C. The morphological, structural, and optical properties of the synthesized CuInS2 nanoparticles are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), Raman scattering, and transmittance measurement, respectively. The SEM image shows the clear particle shape of the calcined CuInS2 nanoparticles. After calcination treatment, the fundamental (112) peak of the XRD spectrum and a broad Raman peak mixed with chalcopyrite and CuAu structures support the improved crystallinity of the calcined CuInS2 nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document