scholarly journals Modeling research of city bus fuel consumption for different driving cycles

2021 ◽  
Vol 2130 (1) ◽  
pp. 012001
Author(s):  
L Grabowski
Keyword(s):  
Carbon Dioxide ◽  
Fuel Consumption ◽  
Carbon Dioxide Emissions ◽  
Operating Conditions ◽  
Urban Traffic ◽  
Pollutant Emissions ◽  
Vehicle Speed ◽  
Traffic Conditions ◽  
Driving Cycles ◽  
Road Gradient

Abstract Simulation studies can be used to determine the fuel consumption and carbon dioxide emissions of city buses. The operating conditions of such vehicles are characterised by a very high variability of vehicle speed due to the large number of stops along the route of the bus. During vehicle testing, driving cycles are used to replicate the real-world conditions and to achieve repeatable test conditions. Such a driving cycle is a profile of speed represented as a function of time or as a function of distance. The speed profile over time can be an advantageous determinant, based on laboratory tests, for estimating fuel consumption and pollutant emissions of city buses. The research subject of this paper was the simulation of bus driving under simulated urban traffic conditions, carried out by means of the VECTO software. VECTO is a tool designed to perform the calculations of fuel consumption and carbon dioxide emissions of vehicles. It enables to model the powertrain of trucks and buses and to carry out simulations on various routes defined by driving cycles. The test object was a mega class bus, equipped with a 225 kW engine. The bus has three axles, including the rear drive axle. The scope of research included four cycles: urban, interurban, urbandelivery and interurban. Each of these was analysed in terms of speed and road gradient. The aim of this work was to perform a simulation study of the effect of the vehicle traffic conditions on the amount of CO2 emitted and fuel consumption. The obtained results were analysed.

scholarly journals Real driving emissions and fuel consumption characteristics of Istanbul public transportation

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 665-667 ◽  
Author(s):  
Orkun Ozener
Keyword(s):  
Fuel Consumption ◽  
Public Transportation ◽  
Primary Source ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Emission Measurement ◽  
Vehicle Speed ◽  
Linear Effect ◽  
Operating Modes ◽  
Portable Emission Measurement System

Public transportation, which uses intra city lines frequently, has vital importance on the cities air pollution. The fossil fuel based drive units, which emits pollutants, are the primary source of this interest. Also, the fuel consumption is another major concern because of economic aspects. For an efficient and clear transportation, the pollutants and fuel consumption has to be analyzed, considering the operating conditions. In this context, the Metrobus line of Istanbul city which crosses from European side to Asian side of the city was analyzed with portable emission measurement system and portable fuel consumption meter devices. The relevant bus operating data were also collected during the operation. The data were analyzed while considering the operating modes like acceleration, deceleration, and constant speed cruises. The emission factors were developed. The pollutant emissions generally decreased as the vehicle speed increased while the fuel consumption increased for the same acceleration level. These results show the importance of operating conditions and their non-linear effect on emissions and fuel consumption Istanbul public transportation.

Environment and Economic Assessment of CNG and Gasoline Engines: An Experimental Analysis

2021 ◽  
Author(s):  
Sridhar Sahoo ◽  
Dhananjay Kumar Srivastava
Keyword(s):  
Carbon Dioxide ◽  
Environmental Impact ◽  
Fuel Consumption ◽  
Coming Out ◽  
Carbon Dioxide Emissions ◽  
Alternative Fuels ◽  
Economic Assessment ◽  
Operating Conditions ◽  
Fuel Cost ◽  
Si Engine

Abstract The application of alternative fuels in automobile engines is gaining more popularity among the scientific community than ever. Most of the research emphasis is on the performance and combustion aspect of the engine. The environmental and economic evaluation of these fuels is also equally important for sustainability, which is relatively unexplored and needs to be evaluated. The present work compares the environmental and economic aspects of a spark ignition (SI) engine fueled with gasoline and compressed natural gas (CNG). To study the environmental impact, regulated and unregulated emissions coming out from the engine exhaust were compared. For economic assessment, annual fuel consumption and associated fuel cost were compared under similar engine operating conditions. The economic cost associated with the environmental impact was calculated based on carbon dioxide emissions and compared using carbon pricing. Experiments on an SI engine were performed at various engine loads to achieve a range of operating conditions to evaluate fuel consumption and engine-out emissions. Results show that a CNG fueled engine has 12.7% lower brake specific fuel consumption than the gasoline engine, which leads to 56% lower fuel cost. It is due to the cumulative effect of higher calorific value and the lower fuel price of CNG compared to gasoline. Additionally, average environment emission and associated cost due to carbon dioxide (CO2) emission reduced by 29% using CNG over gasoline. This study shows that CNG can lead to lesser fuel consumption and its associated fuel and environment cost compared to gasoline.

Techno-Economic Evaluation of Pressurized Oxy-Fuel Combustion Systems

2010 ◽  
Author(s):  
Jongsup Hong ◽  
Ahmed F. Ghoniem ◽  
Randall Field ◽  
Marco Gazzino
Keyword(s):  
Carbon Dioxide ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
Carbon Dioxide Capture ◽  
Fuel Combustion ◽  
Economic Feasibility ◽  
Operating Conditions ◽  
Air Separation ◽  
Separation Unit ◽  
Coal Price

Oxy-fuel combustion coal-fired power plants can achieve significant reduction in carbon dioxide emissions, but at the cost of lowering their efficiency. Research and development are conducted to reduce the efficiency penalty and to improve their reliability. High-pressure oxy-fuel combustion has been shown to improve the overall performance by recuperating more of the fuel enthalpy into the power cycle. In our previous papers, we demonstrated how pressurized oxy-fuel combustion indeed achieves higher net efficiency than that of conventional atmospheric oxy-fuel power cycles. The system utilizes a cryogenic air separation unit, a carbon dioxide purification/compression unit, and flue gas recirculation system, adding to its cost. In this study, we perform a techno-economic feasibility study of pressurized oxy-fuel combustion power systems. A number of reports and papers have been used to develop reliable models which can predict the costs of power plant components, its operation, and carbon dioxide capture specific systems, etc. We evaluate different metrics including capital investments, cost of electricity, and CO2 avoidance costs. Based on our cost analysis, we show that the pressurized oxy-fuel power system is an effective solution in comparison to other carbon dioxide capture technologies. The higher heat recovery displaces some of the regeneration components of the feedwater system. Moreover, pressurized operating conditions lead to reduction in the size of several other critical components. Sensitivity analysis with respect to important parameters such as coal price and plant capacity is performed. The analysis suggests a guideline to operate pressurized oxy-fuel combustion power plants in a more cost-effective way.

scholarly journals An Attempt to Reduce the Emission of Spark-Ignition Engine with Mixtures of Bioethanol and Gasoline as Substitute Fuels

2019 ◽  
Vol 26 (3) ◽  
pp. 31-38
Author(s):  
Wojciech Gis ◽  
Maciej Gis ◽  
Piotr Wiśniowski ◽  
Mateusz Bednarski
Keyword(s):  
Carbon Dioxide ◽  
Fuel Consumption ◽  
Carbon Dioxide Emissions ◽  
Alternative Fuels ◽  
Negative Impact ◽  
Spark Ignition ◽  
Solid Particles ◽  
Spark Ignition Engine ◽  
Maximum Power ◽  
The Impact

Abstract Limiting emissions of harmful substances is a key task for vehicle manufacturers. Excessive emissions have a negative impact not only on the environment, but also on human life. A significant problem is the emission of nitrogen oxides as well as solid particles, in particular those up to a diameter of 2.5 microns. Carbon dioxide emissions are also a problem. Therefore, work is underway on the use of alternative fuels to power the vehicle engines. The importance of alternative fuels applies to spark ignition engines. The authors of the article have done simulation tests of the Renault K4M 1.6 16v traction engine for emissions for fuels with a volumetric concentration of bioethanol from 10 to 85 percent. The analysis was carried out for mixtures as substitute fuels – without doing any structural changes in the engine's crankshafts. Emission of carbon monoxide, carbon dioxide, hydrocarbons, oxygen at full throttle for selected rotational speeds as well as selected engine performance parameters such as maximum power, torque, hourly and unit fuel consumption were determined. On the basis of the simulation tests performed, the reasonableness of using the tested alternative fuels was determined on the example of the drive unit without affecting its constructions, in terms of e.g. issue. Maximum power, torque, and fuel consumption have also been examined and compared. Thus, the impact of alternative fuels will be determined not only in terms of emissions, but also in terms of impact on the parameters of the power unit.

scholarly journals Experimental Analysis of Calculation of Fuel Consumption Rate by On-Road Mileage in a 2.0 L Gasoline-Fueled Passenger Vehicle

2018 ◽  
Vol 8 (12) ◽  
pp. 2390 ◽  
Author(s):  
Jaehyuk Lim ◽  
Yumin Lee ◽  
Kiho Kim ◽  
Jinwook Lee
Keyword(s):  
Fuel Consumption ◽  
Fuel Economy ◽  
Fuel Efficiency ◽  
Co2 Concentration ◽  
The United States ◽  
Traffic Conditions ◽  
Fuel Consumption Rate ◽  
Driving Cycles ◽  
The Difference ◽  
Consumption Value

The five-driving test mode is vehicle driving cycles made by the Environment Protection Association (EPA) in the United States of America (U.S.A.) to fully reflect actual driving environments. Recently, fuel consumption value calculated from the adjusted fuel consumption formula has been more effective in reducing the difference from that experienced in real-world driving conditions, than the official fuel efficiency equation used in the past that only considered the driving environment included in FTP and HWFET cycles. There are many factors that bring about divergence between official fuel consumption and that experienced by drivers, such as driving pattern behavior, accumulated mileage, driving environment, and traffic conditions. In this study, we focused on the factor of causing change of fuel efficiency value, calculated according to how many environmental conditions that appear on the real-road are considered, in producing the fuel consumption formula, and that of the vehicle’s accumulated mileage in a 2.0 L gasoline-fueled vehicle. So, the goals of this research are divided into four major areas to investigate divergence in fuel efficiency obtained from different equations, and what factors and how much CO2 and CO emissions that are closely correlated to fuel efficiency change, depending on the cumulative mileage of the vehicle. First, the fuel consumption value calculated from the non-adjusted formula, was compared with that calculated from the corrected fuel consumption formula. Also, how much CO2 concentration levels change as measured during each of the three driving cycles was analyzed as the vehicle ages. In addition, since the US06 driving cycle is divided into city mode and highway mode, how much CO2 and CO production levels change as the engine ages during acceleration periods in each mode was investigated. Finally, the empirical formula was constructed using fuel economy values obtained when the test vehicle reached 6500 km, 15,000 km, and 30,000 km cumulative mileage, to predict how much fuel consumption of city and highway would worsen, when mileage of the vehicle is increased further. When cumulative mileage values set in this study were reached, experiments were performed by placing the vehicle on a chassis dynamometer, in compliance with the carbon balance method. A key result of this study is that fuel economy is affected by various fuel consumption formula, as well as by aging of the engine. In particular, with aging aspects, the effect of an aging engine on fuel efficiency is insignificant, depending on the load and driving situation.

scholarly journals The Development of Electromobility in Poland and EU States as a Tool for Management of CO2 Emissions

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2942 ◽  
Author(s):  
Karol Tucki ◽  
Olga Orynycz ◽  
Antoni Świć ◽  
Mateusz Mitoraj-Wojtanek
Keyword(s):  
Carbon Dioxide ◽  
European Union ◽  
Carbon Dioxide Emissions ◽  
Power Plants ◽  
Primary Energy ◽  
Original Method ◽  
Pollutant Emissions ◽  
The European Union ◽  
Car Market ◽  
The Impact

The article analyzes the dynamics of the development of the electromobility sector in Poland in the context of the European Union and due to the economic situation and development of the electromobility sector in the contexts of Switzerland and Norway. On the basis of obtained data, a forecast was made which foresees the most likely outlook of the electric car market in the coming years. The forecast was made using the creeping trend method, and extended up to 2030. As part of the analysis of the effect of the impact of electromobility, an original method was proposed for calculating the primary energy factor (PEF) primary energy ratio in the European Union and in its individual countries, which illustrates the conversion efficiency of primary energy into electricity and the overall efficiency of the power system. The original method was also verified, referring to the methods proposed by the Fraunhofer-Institut. On the basis of all previous actions and analyses, an assessment was made of the impact of the development of the electromobility sector on air quality in the countries studied. Carbon dioxide tank-to-wheels emission reductions which result from the conversion of the car fleet from conventional vehicles to electric motors were then calculated. In addition to reducing carbon dioxide emissions, other pollutant emissions were also calculated, such as carbon monoxide (CO), nitrogen oxides (NOx) and particulate matter (PM). The increase in the demand for electricity resulting from the needs of electric vehicles was also estimated. On this basis, and also on the basis of previously calculated primary energy coefficients, the emission reduction values have been adjusted for additional emissions resulting from the generation of electricity in power plants.

scholarly journals Prediction of Exhaust Emission Costs in Air and Road Transportation

2019 ◽  
Vol 11 (17) ◽  
pp. 4688 ◽  
Author(s):  
Olja Čokorilo ◽  
Ivan Ivković ◽  
Snežana Kaplanović
Keyword(s):  
Carbon Dioxide ◽  
Road Transport ◽  
Structure Type ◽  
Influential Factors ◽  
Operating Conditions ◽  
Air Transport ◽  
Transport Sector ◽  
Exhaust Emission ◽  
Vehicle Speed ◽  
Road Transportation

In this paper, the calculation of exhaust emission costs originating from aircraft and road vehicles in the base year 2017 and in the forecasting year 2032, in the Republic of Serbia, was carried out. The presented methodology includes a number of influential factors for air transport (airport capacity, number of operations, aircraft type, relevant engine, range) and for road transport (changing of traffic volumes, design and operating speeds, the quality of the pavement structure, type of terrain and category of road sections, dependence of exhaust emission from changes in vehicle speed). It was found that in the current operating conditions, the dominant costs in the total exhaust emission costs are the costs of nitrogen oxides (61%) in road transport, whilst carbon dioxide costs are dominant in air transport (52%). In the future, carbon dioxide costs will have a share of over 80% in the road transport sector and over 58% in the air transport sector in total exhaust emission costs. The average exhaust emission costs per one aircraft operation (international flights) will range from 141 to 145€. In road transport, the average exhaust emission costs at 100 km in 2032 will range from 1.8 to 2.2€.

Evaluation of hot water storage strategy in internal combustion engine on different driving cycles using numerical simulations

2017 ◽  
Vol 232 (8) ◽  
pp. 1019-1035 ◽  
Author(s):  
Hanna Sara ◽  
David Chalet ◽  
Mickaël Cormerais ◽  
Jean-François Hetet
Keyword(s):  
Ambient Temperature ◽  
Fuel Consumption ◽  
Thermal Management ◽  
Negative Impact ◽  
Combustion Engine ◽  
Driving Cycle ◽  
Hot Water ◽  
Pollutant Emissions ◽  
Engine Model ◽  
Driving Cycles

Since the main interest worldwide of green environment companies is to reduce pollutant emissions, the automotive industry is aiming to improve engine efficiency in order to reduce fuel consumption. Recently, studies have been shifted from upgrading the engine to the auxiliary systems attached to it. Thermal management is one of the successful fields that has shown promise in minimizing fuel consumption and reducing pollutant emissions. Throughout this work, a four-cylinder turbocharged diesel engine model was developed on GT-Power. Also, a thermal code has been developed in parallel on GT-Suite, in which the different parts of the coolant and lubricant circuits were modeled and calibrated to have the best agreement with the temperature profile of the two fluids in the system. Once the model was verified, hot coolant storage, a thermal management strategy, was applied to the system to assess the fuel consumption gain. The storage tank was located downstream the thermostat and upstream the radiator with three valves to control the coolant flow. The place was chosen to avoid negative impact on the cold start-up of the engine when the tank is at the ambient temperature. This strategy was applied on different driving cycles such as the NEDC, WLTC, CADC (urban and highway), and an in-house developed driving cycle. The ambient temperature was varied between −7°C to represent the coldest winter and 20°C. The results of this study summarize the ability of the hot coolant storage strategy in reducing the fuel consumption, and show the best driving cycle that needs to be applied on along with the influence of the different ambient temperatures.

Sign in / Sign up

Export Citation Format

Share Document