scholarly journals Finite Element Modeling of Tension Stiffening and Cracking of Reinforced Concrete Components: State of Art

2021 ◽  
Vol 889 (1) ◽  
pp. 012082
Author(s):  
Seema ◽  
Aditya Kumar Tiwary ◽  
R. Zandonini
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Progressive Collapse ◽  
Element Model ◽  
Extensive Study ◽  
Tension Stiffening ◽  
Modelling Techniques ◽  
Numerical Research ◽  
Design Requirements ◽  
The Impact

Abstract The scientific community has been debating the vulnerability of structures to progressive collapse and how to mitigate the impact of local damages leading to un-proportional collapse. Recent tragedies have highlighted the necessity for particular design requirements to provide appropriate safety levels against progressive collapse as a result of damages caused by unusual loads. The performance of composite and reinforced concrete components in the realm of large displacements is presently the focus of study. The behaviour of reinforced concrete (RC) components, as well as the finite element model used to simulate RC parts under tension, were critically examined. This has aided in the understanding of concrete’s non-negligible contribution to tension stiffening response up to failure, particularly in the case of composite constructions with discontinuous geometry. The extensive study of literature provided insight into various modelling techniques and advised that experimental and numerical research be used to enhance diverse possibilities of model exploration.

scholarly journals Collapse Analysis of a Transmission Tower-Line System Induced by Ice Shedding

2021 ◽  
Vol 9 ◽  
Author(s):  
Jiaxiang Li ◽  
Biao Wang ◽  
Jian Sun ◽  
Shuhong Wang ◽  
Xiaohong Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Transmission Lines ◽  
Progressive Collapse ◽  
Element Model ◽  
Transmission Tower ◽  
Line System ◽  
Finite Element Software ◽  
Transmission Towers ◽  
Ice Shedding ◽  
The Impact

Ice shedding causes transmission lines to vibrate violently, which induces a sharp increase in the longitudinal unbalanced tension of the lines, even resulting in the progressive collapse of transmission towers in serious cases, which is a common ice-based disaster for transmission tower-line systems. Based on the actual engineering characteristics of a 500 kV transmission line taken as the research object, a finite element model of a two-tower, three-line system is established by commercial ANSYS finite element software. In the modeling process, the uniform mode method is used to introduce the initial defects, and the collapse caused by ice shedding and its influencing parameters are systematically studied. The results show that the higher the ice-shedding height is, the greater the threat of ice shedding to the system; furthermore, the greater the span is, the shorter the insulator length and the greater the dynamic response of the line; the impact of ice shedding should be considered in the design of transmission towers.

scholarly journals A Computational Study of the Shear Behavior of Reinforced Concrete Beams Affected from Alkali–Silica Reactivity Damage

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3346
Author(s):  
Bora Gencturk ◽  
Hadi Aryan ◽  
Mohammad Hanifehzadeh ◽  
Clotilde Chambreuil ◽  
Jianqiang Wei
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Parametric Study ◽  
Computational Study ◽  
Element Model ◽  
Shear Behavior ◽  
Shear Capacity ◽  
Reinforced Concrete Beams ◽  
Alkali Silica Reactivity ◽  
Concrete Mechanical Properties

In this study, an investigation of the shear behavior of full-scale reinforced concrete (RC) beams affected from alkali–silica reactivity damage is presented. A detailed finite element model (FEM) was developed and validated with data obtained from the experiments using several metrics, including a force–deformation curve, rebar strains, and crack maps and width. The validated FEM was used in a parametric study to investigate the potential impact of alkali–silica reactivity (ASR) degradation on the shear capacity of the beam. Degradations of concrete mechanical properties were correlated with ASR expansion using material test data and implemented in the FEM for different expansions. The finite element (FE) analysis provided a better understanding of the failure mechanism of ASR-affected RC beam and degradation in the capacity as a function of the ASR expansion. The parametric study using the FEM showed 6%, 19%, and 25% reduction in the shear capacity of the beam, respectively, affected from 0.2%, 0.4%, and 0.6% of ASR-induced expansion.

Investigation on the shaft voltage generation of large synchronous turboalternators

2020 ◽  
Vol 39 (5) ◽  
pp. 1145-1156
Author(s):  
Kevin Darques ◽  
Abdelmounaïm Tounzi ◽  
Yvonnick Le-menach ◽  
Karim Beddek
Keyword(s):  
Finite Element ◽  
Design Methodology ◽  
Short Circuit ◽  
Element Model ◽  
Stator Winding ◽  
Content Type ◽  
Voltage Generation ◽  
The Impact ◽  
Investigation Process ◽  
Circulating Currents

Purpose This paper aims to go deeper on the analysis of the shaft voltage of large turbogenerators. The main interest of this study is the investigation process developed. Design/methodology/approach The analysis of the shaft voltage because of several defects is based on a two-dimensional (2D) finite element modeling. This 2D finite element model is used to determine the shaft voltage because of eccentricities or rotor short-circuit. Findings Dynamic eccentricities and rotor short circuit do not have an inherent impact on the shaft voltage. Circulating currents in the stator winding because of defects impact the shaft voltage. Originality/value The original value of this paper is the investigation process developed. This study proposes to quantify the impact of a smooth stator and then to explore the contribution of the real stator winding on the shaft voltage.

Behavior of Structures Using Simple Plastic Hinge Theory

1994 ◽  
Author(s):  
Ramakrishnan Maruthayappan ◽  
Hamid M. Lankarani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cantilever Beam ◽  
Reliable Method ◽  
Plastic Hinge ◽  
Element Model ◽  
Finite Element Models ◽  
Computational Program ◽  
Hinge Model ◽  
The Impact

Abstract The behavior of structures under the impact or crash situations demands an efficient modeling of the system for its behavior to be predicted close to practical situations. The various formulations that are possible to model such systems are spring mass models, finite element models and plastic hinge models. Of these three techniques, the plastic hinge theory offers a more accurate model compared to the spring mass formulation and is much simpler than the finite element models. Therefore, it is desired to model the structure using plastic hinges and to use a computational program to predict the behavior of structures. In this paper, the behavior of some simple structures, ranging from an elementary cantilever beam to a torque box are predicted. It is also shown that the plastic hinge theory is a reliable method by comparing the results obtained from a plastic hinge model of an aviation seat structure with that obtained from a finite element model.

Simulation Analysis of Secondary-Load Rc Square Columns Strengthened with IFRP

2014 ◽  
Vol 501-504 ◽  
pp. 578-582
Author(s):  
Liang Hsu ◽  
Ming Long Hu ◽  
Jun Zhi Zhang
Keyword(s):  
Finite Element ◽  
Simulation Analysis ◽  
Element Model ◽  
Fiber Reinforced Polymer ◽  
Experimental Result ◽  
Compression Process ◽  
Reinforced Polymer ◽  
Secondary Load ◽  
The Impact ◽  
The Finite Element Model

Considering secondary load, simulate the axial compression process of reinforced concrete square columns strengthened with igneous rock fiber reinforced polymer with Abaqus. Make a comparison between the simulation result and experimental result. The finite-element model can simulate the experiment preferably. And the impact of lagged strain is very obvious.

Additional Damping Conditions Analysis and Calculation for Exciting Force and External Load

2013 ◽  
Vol 579-580 ◽  
pp. 507-511
Author(s):  
Yi Xiang Liu ◽  
Yong Mei Wang
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Structure Design ◽  
Exciting Force ◽  
Reduction Gear ◽  
Solid Model ◽  
Gear Noise ◽  
Force Reduction ◽  
And Control ◽  
The Impact

This paper firstly starting mechanism of vibration and noise from gear, gear noise mechanism is explained, and analyze the factors and the impact of noise on the gear reducer. Secondly, the establishment of a complete solid model of gear reducer and reducer model for finite element model, the reduction gear box gear reducer of modal analysis and finite element modal calculation, and points out the dynamic analysis of structure, size and weight factor is proportional to the reciprocal of the modal frequencies of each mode is the with the frequency is low, that is, the greater the weight. Once again, the main measure of load and control of gear noise of gear is analyzed, including the calculation, for exciting force reduction gear reducer gear load computation. The analysis and calculation are the theoretical basis of gear structure design and its performance evaluation.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals Response of the Flat Reinforced Concrete Floor Slab with Openings under Cyclic In-Plane Loading

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Eden Shukri Kalib ◽  
Yohannes Werkina Shewalul
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Lateral Displacement ◽  
Load Capacity ◽  
Element Model ◽  
Absorption Capacity ◽  
Hysteretic Behavior ◽  
Element Analysis ◽  
Floor Slab ◽  
Floor Slabs

The responses of flat reinforced concrete (RC) floor slabs with openings subjected to horizontal in-plane cyclic loads in addition to vertical service loads were investigated using nonlinear finite element analysis (FEA). A finite element model (FEM) was designed to perform a parametric analysis. The effects of opening sizes (7%, 14%, 25%, and 30% of the total area of the slab), opening shapes (elliptical, circular, L-shaped, T-shaped, cross, and rectangular), and location on the hysteretic behavior of the floor slab were considered. The research indicated that openings in RC floor slabs reduce the energy absorption capacity and stiffness of the floor slab. The inclusion of 30% opening on the floor slab causes a 68.5%, 47.3%, and 45.6% drop in lateral load capacity, stiffness, and lateral displacement, respectively, compared to the floor slab with no openings. The flat RC floor slab with a circular opening shape has increased efficiency. The placement of the openings is more desirable by positioning the openings at the intersection of two-column strips.

scholarly journals Analysing Random Vibration of KLT Box during Transporting by Finite Element Method

10.29007/b1th ◽  
2022 ◽  
Author(s):  
Cong Hoa Vu ◽  
Ngoc Thien Ban Dang
Keyword(s):  
Finite Element ◽  
Spectral Density ◽  
Power Spectral Density ◽  
Automotive Industry ◽  
Random Vibration ◽  
Element Model ◽  
Vibration Testing ◽  
Time Data ◽  
Power Spectral ◽  
The Impact

Today, freight is an extremely important industry for the world we are living. Fast transportation, large volume...will optimize the cost, time and effort. Besides, ensuring the products safety is a matter of concern. During transporting, it is inevitable that the vibration caused by the engine, rough road surface...the cargo inside can be damaged. Automobile industries have prime importance to vibration testing. Sine vibration testing is performed when we have been given with only one frequency at given time instant. Trend to perform random vibration testing has been increased in recent times. As random vibration considers all excited frequencies in defined spectrum at known interval of time, it gives real-time data of vibration severities. The vibration severity is expressed in terms of Power Spectral Density (PSD). KLT box is an industrial stacking container conforming to the VDA 4500 standard that was defined by German Association of the Automotive Industry (VDA) for the automotive industry. The aim of this paper is study about random vibration and power spectral density analysis, how it can be used to predict the impact of hash road to the KLT box on container / truck during transportation. Finite element model is developed in ANSYS, modal analysis and random vibration analysis were done.

Sign in / Sign up

Export Citation Format

Share Document