Effects of bonding temperature on the microstructures and mechanical properties of the C/C-Cf/SiC composite joint prepared by in situ hot-press diffusion bonding using Ti–Si–C compound as interlayer

2019 ◽  
Vol 6 (11) ◽  
pp. 115620
Author(s):  
Jie Wang ◽  
Yanlin Xiong ◽  
Hao Li ◽  
Guanzhong Yang ◽  
Fuqi Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Diffusion Bonding ◽  
Bonding Temperature ◽  
Hot Press ◽  
Composite Joint ◽  
Microstructures And Mechanical Properties

scholarly journals Fabrication and mechanical properties of Al2O3/TiAl in situ composites doped with Nb2O5

2015 ◽  
Vol 47 (3) ◽  
pp. 311-317 ◽  
Author(s):  
F. Wang ◽  
N. Fan ◽  
J. Zhu ◽  
H. Jiang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Hot Press ◽  
Dispersion Method ◽  
Powder Mixtures ◽  
In Situ Composites ◽  
Microstructures And Mechanical Properties

Al2O3/TiAl composites were successfully fabricated from powder mixtures of Ti, Al, TiO2, Cr2O3 and Nb2O5 by a hot-press-assisted exothermic dispersion method. The effect of the Cr2O3 and Nb2O5 addition on the microstructures and mechanical properties of Al2O3/TiAl composites was characterized. The results showed that the specimens are mainly composed of TiAl, Ti3Al, Al2O3, NbAl3 and Cr2Al. The Vicker-hardness and density of Al2O3/TiAl composites increase gradually with the increase of Nb2O5 content. When the Nb2O5 content was 6.54 wt %, the flexural strength and fracture toughness of the composites have a maximum values of 789.79 MPa and 9.69 MPa?m1/2, respectively. The improvement of mechanical properties is discussed in detail.

Effect of Si Addition on the Microstructures and Mechanical Properties of TiAl Intermetallics

2011 ◽  
Vol 239-242 ◽  
pp. 413-416 ◽  
Author(s):  
Jian Feng Zhu ◽  
Wen Wen Yang ◽  
Shao Dan Li
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Hot Press ◽  
The Matrix ◽  
Press Method ◽  
Microstructures And Mechanical Properties ◽  
Si Content ◽  
Si Addition

TiAl/Ti5Si3 in situ composites were successfully fabricated by reactive hot-press method from powder mixtures of Ti, Al and Si. The influence of the Si addition on the microstructures and mechanical properties of TiAl/Ti5Si3 composites was investigated in detail. The results show that an appropriate amount of addition of Si refined the matrix structure obviously due to the in situ formed Ti5Si3, and as a result, the flexural strength and fracture toughness of the composites are modified. When the Si content is 1.82 wt %, the flexural strength and the fracture toughness reach the maximum value of 685.67 MPa and 9.02 MPa·m1/2, respectively. The enhancing mechanism was also discussed.

scholarly journals Effect of Sintering Temperature on Microstructure and Mechanical Properties of Hot-Pressed Fe/FeAl2O4 Composite

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Kuai Zhang ◽  
Yungang Li ◽  
Hongyan Yan ◽  
Chuang Wang ◽  
Hui Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Hot Press ◽  
Microstructure And Mechanical Properties ◽  
Powder Particles ◽  
Hot Press Sintering ◽  
Sintering Method

An Fe/FeAl2O4 composite was prepared with Fe-Fe2O3-Al2O3 powder by a hot press sintering method. The mass ratio was 6:1:2, sintering pressure was 30 MPa, and holding time was 120 min. The raw materials for the powder particles were respectively 1 µm (Fe), 0.5 µm (Fe2O3), and 1 µm (Al2O3) in diameter. The effect of sintering temperature on the microstructure and mechanical properties of Fe/FeAl2O4 composite was studied. The results showed that Fe/FeAl2O4 composite was formed by in situ reaction at 1300 °C–1500 °C. With the increased sintering temperature, the microstructure and mechanical properties of the Fe/FeAl2O4 composite showed a change law that initially became better and then became worse. The best microstructure and optimal mechanical properties were obtained at 1400 °C. At this temperature, the grain size of Fe and FeAl2O4 phases in Fe/FeAl2O4 composite was uniform, the relative density was 96.7%, and the Vickers hardness and bending strength were 1.88 GPa and 280.0 MPa, respectively. The wettability between Fe and FeAl2O4 was enhanced with increased sintering temperature. And then the densification process was accelerated. Finally, the microstructure and mechanical properties of the Fe/FeAl2O4 composite were improved.

scholarly journals Superplastic Forming and Reaction Diffusion Bonding Process of Hollow Structural Component for Mg-Gd-Y-Zn-Zr Rare Earth Magnesium Alloy

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 152
Author(s):  
Peng Peng ◽  
Shaosong Jiang ◽  
Zhonghuan Qin ◽  
Zhen Lu
Keyword(s):  
Mechanical Properties ◽  
Diffusion Bonding ◽  
Structural Component ◽  
Bonding Temperature ◽  
Reaction Diffusion ◽  
Superplastic Forming ◽  
Tensile Tests ◽  
Interface Roughness ◽  
Size Growth ◽  
Cu Interlayer

This work fabricated a double hollow structural component of Mg-8.3Gd-2.9Y-0.8Zn-0.2Zr alloy by superplastic forming (SPF) and reaction-diffusion bonding (RDB). The superplastic characteristic and mechanical properties of Mg-8.3Gd-2.9Y-0.8Zn-0.2Zr alloy sheets at 250–450 °C were studied. Tensile tests showed that the maximum elongation of tensile specimens was about 1276.3% at 400 °C under a strain rate of 1 × 10−3 s−1. Besides, the effect of bonding temperature and interface roughness on microstructure and mechanical properties of the reaction diffusion-bonded joints with a Cu interlayer was investigated. With the increase of temperature, the diffusion coefficient of Cu increases, and the diffusion transition region becomes wider, leading to tightening bonding of the joint. However, the bonding quality of the joint will deteriorate due to grain size growth at higher temperatures. Shear tests showed that the highest strength of the joints was 152 MPa (joint efficiency = 98.7%), which was performed at 460 °C.

Sign in / Sign up

Export Citation Format

Share Document