scholarly journals Humidification-dehumidification desalination process using green hydrogen and heat recovery

2021 ◽  
Author(s):  
Adrian Brunini ◽  
Maria del Carmen Garcia ◽  
Augusto Melgarejo ◽  
Roberto Guillermo Rodriguez
Keyword(s):  
Fuel Consumption ◽  
Heat Recovery ◽  
Pure Water ◽  
Recovery Process ◽  
Good Alternative ◽  
Continuous Operation ◽  
Operating Conditions ◽  
Auxiliary Power ◽  
Increase Productivity ◽  
Operation Cost

Abstract We propose the use of green hydrogen as a fuel for a seawater heater in a humidification / dehumidification (HDH) desalination plant to increase its productivity, to allow scaling to large dimensions without negative environmental effects, and to guarantee continuous operation. We develop a mathematical model of the proposed HDH configuration. For operating conditions that guarantee very low NOX production, the fuel consumption is ~0.03 kg of H2 per kg of pure water produced. If the exhaust gases from the seawater heater are used for heat recovery, the GOR of the equipment may increase by up to 39 % in relation to the same equipment operating without heat recovery. The operation cost of freshwater is comparable to the costs obtained by other equipment in the literature. If the water produced in the combustion of hydrogen is condensed during the heat recovery process and then added to the freshwater produced, the production cost is reduced by 20 %. We found that an excess of air in the air+fuel mix beyond the minimum value appropriate for a low NOX generation does not provide significant benefits. The efficiency of the seawater heater has an impact on the production of pure water, but this impact is strongly mitigated by the heat recovery process. Fuel consumption increases proportionally with the decrease in the effectiveness of the heat recovery device, which is a key parameter for optimal performance. A hydrogen heater is also a good alternative as an auxiliary power source to guarantee continuous operation. On sunny hours a H2 heater may be used to increase productivity preheating the seawater, and at night the system could operate 100 % based on H2.

The Reduction of Fuel Consumption on the Example of Ecological Hybrid Buses

2014 ◽  
Vol 518 ◽  
pp. 96-101 ◽  
Author(s):  
Maciej Bajerlein ◽  
Lukasz Rymaniak
Keyword(s):  
Fuel Consumption ◽  
Public Transport ◽  
Objective Assessment ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Actual Operating ◽  
Urban Public Transport ◽  
The Subject ◽  
Economic Balance ◽  
Operation Cost

For city buses, the costs of operation and maintenance are critical in the overall purchase and operation cost analysis. That is why the scientists from the Institute of Combustion Engines and Transport have taken up the subject of economic balance on the example of urban public transport operators. For an objective assessment of the fuel consumption it is necessary to determine all the variables. Hence, driving tests are developed that characterize the actual operating conditions and stringent procedures of their realization are set out. The paper presents the results of the fuel consumption tests carried out on public transport buses (SORT Standardized On-Road Tests Cycles).

КОНЦЕПЦІЯ СТВОРЕННЯ СИЛОВОЇ УСТАНОВКИ СІМЕЙСТВА РЕГІОНАЛЬНИХ ПАСАЖИРСЬКИХ ЛІТАКІВ АН-148/АН-158

2019 ◽  
pp. 50-63
Author(s):  
О. Д. Донець ◽  
В. П. Іщук
Keyword(s):  
Power Plant ◽  
Noise Reduction ◽  
Fuel Consumption ◽  
Electronic System ◽  
Electronic Control ◽  
Level Of Automation ◽  
Auxiliary Power ◽  
Power Plant Control ◽  
Technical Status ◽  
Air Intake

The basic results of calculation and research works carried out in the process of creation of power unit of regional passenger airplanes’ family are given. The design features of the propulsion engines and engine of the auxiliary power plant are described. The aforementioned propulsion system includes propulsion engines D-436-148 and engine AI-450-MS of auxiliary power plant. In order to comply with the requirements of Section 4 of the ICAO standard (noise reduction of the aircraft in site), in part of ensuring the noise reduction of engines, when creating the power plant of the An-148/An-158 aircraft family, a single- and double-layer acoustic filler was used in the structure of the engine nacelle and air intake. The use of electronic system for automatic control of propulsion engines such as FADEC and its integration into the digital airborne aircraft complex ensured the operation of engines, included in the power plant provided with high specific fuel consumption, as well as increased the level of automation of the power plant control and monitoring, and ensured aircraft automation landing in ICAO category 3A. In addition, the use of the aforementioned electronic system, allowed to operate the power plant of the aircraft in accordance with technical status. The use of the AI-450-MS auxiliary power plant with an electronic control system such as FADEC, and the drive of the service compressor from a free turbine, eliminated the effect of changes in power and air takeoff, on the deviation of the engine from optimal mode, which also minimized the fuel consumption. The use of fuel metering system TIS-158, allowed to ensure control of its condition and assemblies, without the use of auxiliary devices, built-in control means. In the fire protection system, the use of the electronic control and monitor unit, as well as the use of digital serial code for the exchange of information between the elements of the system and the aircraft systems, has reduced the number of connections, which increased the reliability of the system and reduced its weight characteristics.

Stirling system optimization for series hybrid electric vehicles

2021 ◽  
pp. 095440702110180
Author(s):  
Charbel R Ghanem ◽  
Elio N Gereige ◽  
Wissam S Bou Nader ◽  
Charbel J Mansour
Keyword(s):  
Fuel Consumption ◽  
Hybrid Electric Vehicle ◽  
Combustion Engine ◽  
Optimization Technique ◽  
System Optimization ◽  
Energy Management Strategy ◽  
Fuel Savings ◽  
Auxiliary Power ◽  
Hybrid Electric ◽  
External Combustion

There have been many studies conducted to replace the conventional internal combustion engine (ICE) with a more efficient engine, due to increasing regulations over vehicles’ emissions. Throughout the years, several external combustion engines were considered as alternatives to these traditional ICEs for their intrinsic benefits, among which are Stirling machines. These were formerly utilized in conventional powertrains; however, they were not implemented in hybrid vehicles. The purpose of this study is to investigate the possibility of implementing a Stirling engine in a series hybrid electric vehicle (SHEV) to substitute the ICE. Exergy analysis was conducted on a mathematical model, which was developed based on a real simple Stirling, to pinpoint the room for improvements. Then, based on this analysis, other configurations were retrieved to reduce exergy losses. Consequently, a Stirling-SHEV was modeled, to be integrated as auxiliary power unit (APU). Hereafter, through an exergo-technological detailed selection, the best configuration was found to be the Regenerative Reheat two stages serial Stirling (RRe-n2-S), offering the best efficiency and power combination. Then, this configuration was compared with the Regenerative Stirling (R-S) and the ICE in terms of fuel consumption, in the developed SHEV on the WLTC. This was performed using an Energy Management Strategy (EMS) consisting of a bi-level optimization technique, combining the Non-dominated Sorting Genetic Algorithm (NSGA) with the Dynamic Programming (DP). This arrangement is used to diminish the fuel consumption, while considering the reduction of the APU’s ON/OFF switching times, avoiding technical issues. Results prioritized the RRe-n2-S presenting 12.1% fuel savings compared to the ICE and 14.1% savings compared to the R-S.

scholarly journals Component-Oriented Modeling of a Micro-Scale Organic Rankine Cycle System for Waste Heat Recovery Applications

2021 ◽  
Vol 11 (5) ◽  
pp. 1984
Author(s):  
Ramin Moradi ◽  
Emanuele Habib ◽  
Enrico Bocci ◽  
Luca Cioccolanti
Keyword(s):  
Electric Power ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pump Efficiency ◽  
Micro Scale

Organic Rankine cycle (ORC) systems are some of the most suitable technologies to produce electricity from low-temperature waste heat. In this study, a non-regenerative, micro-scale ORC system was tested in off-design conditions using R134a as the working fluid. The experimental data were then used to tune the semi-empirical models of the main components of the system. Eventually, the models were used in a component-oriented system solver to map the system electric performance at varying operating conditions. The analysis highlighted the non-negligible impact of the plunger pump on the system performance Indeed, the experimental results showed that the low pump efficiency in the investigated operating range can lead to negative net electric power in some working conditions. For most data points, the expander and the pump isentropic efficiencies are found in the approximate ranges of 35% to 55% and 17% to 34%, respectively. Furthermore, the maximum net electric power was about 200 W with a net electric efficiency of about 1.2%, thus also stressing the importance of a proper selection of the pump for waste heat recovery applications.

Optimization for speed regulation strategy of compound coupled hydro-mechanical transmission

2020 ◽  
pp. 095440702098056
Author(s):  
Jin Yu ◽  
Pengfei Shen ◽  
Zhao Wang ◽  
Yurun Song ◽  
Xiaohan Dong
Keyword(s):  
Fuel Consumption ◽  
Dynamic Programming Algorithm ◽  
Operating Conditions ◽  
Programming Algorithm ◽  
Speed Ratio ◽  
Mechanical Transmission ◽  
Speed Regulation ◽  
Ratio Change ◽  
Low Efficiency ◽  
Wheel Loaders

Heavy duty vehicles, especially special vehicles, including wheel loaders and sprinklers, generally work with drastic changes in load. With the usage of a conventional hydraulic mechanical transmission, they face with these problems such as low efficiency, high fuel consumption and so forth. Some scholars focus on the research to solve these issues. However, few of them take into optimal strategies the fluctuation of speed ratio change, which can also cause a lot of problems. In this study, a novel speed regulation is proposed which cannot only solve problems above but also overcome impact caused by speed ratio change. Initially, based on the former research of the Compound Coupled Hydro-mechanical Transmission (CCHMT), the basic characteristics of CCHMT are analyzed. Besides, to solve these problems, dynamic programming algorithm is utilized to formulate basic speed regulation strategy under specific operating condition. In order to reduce the problem caused by speed ratio change, a new optimization is applied. The results indicate that the proposed DP optimal speed regulation strategy has better performance on reducing fuel consumption by up to 1.16% and 6.66% in driving cycle JN1015 and in ECE R15 working condition individually, as well as smoothing the fluctuation of speed ratio by up to 12.65% and 19.01% in those two driving cycles respectively. The processes determining the speed regulation strategy can provide a new method to formulate the control strategies of CCHMT under different operating conditions particularlly under real-world conditions.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

Performance Improvements in Cooker-Top Gas Burners for Small Aspect Ratio Changes

2017 ◽  
Vol 9 (4) ◽  
Author(s):  
Robson L. Silva ◽  
Bruno V. Sant′Ana ◽  
José R. Patelli ◽  
Marcelo M. Vieira
Keyword(s):  
Energy Conversion ◽  
Fuel Consumption ◽  
Conversion Efficiency ◽  
Minimum Energy ◽  
Energy Conversion Efficiency ◽  
Energy Performance ◽  
Operating Conditions ◽  
Lower Fuel Consumption ◽  
Performance Improvements ◽  
Aspect Ratios

This paper aims to identify performance improvements in cooker-top gas burners for changes in its original geometry, with aspect ratios (ARs) ranging from 0.25 to 0.56 and from 0.28 to 0.64. It operates on liquefied petroleum gas (LPG) and five thermal power (TP) levels. Considering the large number of cooker-top burners currently being used, even slight improvements in thermal performance resulting from a better design and recommended operating condition will lead to a significant reduction of energy consumption and costs. Appropriate instrumentation was used to carry out the measurements and methodology applied was based on regulations from INMETRO (CONPET program for energy conversion efficiency in cook top and kilns), ABNT (Brazilian Technical Standards Normative) and ANP—National Agency of Petroleum, Natural Gas (NG) and Biofuels. The results allow subsidizing recommendations to minimum energy performance standards (MEPS) for residential use, providing also higher energy conversion efficiency and/or lower fuel consumption. Main conclusions are: (i) Smaller aspect ratios result in the same heating capacity and higher efficiency; (ii) higher aspect ratios (original burners) are fuel consuming and inefficient; (iii) operating conditions set on intermediate are lower fuel consumption without significant differences in temperature increases; (iv) Reynolds number lower than 500 provides higher efficiencies.

Potential of the Variable Valve Actuation (VVA) Strategy on a Heavy Duty CNG Engine

2014 ◽  
Author(s):  
Mirko Baratta ◽  
Roberto Finesso ◽  
Daniela Misul ◽  
Ezio Spessa ◽  
Yifei Tong ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Operating Conditions ◽  
Intake Valve ◽  
Heavy Duty ◽  
Engine Emissions ◽  
Variable Valve Actuation ◽  
Cng Engine ◽  
Variable Valve ◽  
Working Point ◽  
Valve Actuation

The environmental concerns officially aroused in 1970s made the control of the engine emissions a major issue for the automotive industry. The corresponding reduction in fuel consumption has become a challenge so as to meet the current and future emission legislations. Given the increasing interest retained by the optimal use of a Variable Valve Actuation (VVA) technology, the present paper investigates into the potentials of combining the VVA solution to CNG fuelling. Experiments and simulations were carried out on a heavy duty 6-cylinders CNG engine equipped with a turbocharger displaying a twin-entry waste-gate-controlled turbine. The analysis aimed at exploring the potentials of the Early Intake Valve Closure (EIVC) mode and to identify advanced solutions for the combustion management as well as for the turbo-matching. The engine model was developed within the GT-Power environment and was finely tuned to reproduce the experimental readings under steady state operations. The 0D-1D model was hence run to reproduce the engine operating conditions at different speeds and loads and to highlight the effect of the VVA on the engine performance as well as on the fuel consumption and engine emissions. Pumping losses proved to reduce to a great extent, thus decreasing the brake specific fuel consumption (BSFC) with respect to the throttled engine. The exhaust temperature at the turbine inlet was kept to an almost constant value and minor variations were allowed. This was meant to avoid an excessive worsening in the TWC working conditions, as well as deterioration in the turbocharger performance during load transients. The numerical results also proved that full load torque increases can be achieved by reducing the spark advance so that a higher enthalpy is delivered to the turbocharger. Similar torque levels were also obtained by means of Early Intake Valve Closing strategy. For the latter case, negligible penalties in the fuel consumption were detected. Moreover, for a given combustion phasing, the IVC angle directly controls the mass-flow rate and thus the torque. On the other hand, a slight dependence on the combustion phasing can be detected at part load. Finally, the simulations assessed for almost constant fuel consumption for a wide range of IVC and SA values. Specific attention was also paid to the turbocharger group functioning and to its correct matching to the engine working point. The simulations showed that the working point on the compressor map can be optimized by properly setting the spark advance (SA) as referred to the adopted intake-valve closing angle. It is anyhow worth observing that the engine high loads set a constraint deriving from the need to meet the limits on the peak firing pressure (PFP), thus limiting the possibility to optimize the working point once the turbo-matching is defined.

Sign in / Sign up

Export Citation Format

Share Document