scholarly journals Evolution and properties of young oceanic crust: constraints from Poisson's ratio

Author(s):  
M J Funnell ◽  
A H Robinson ◽  
R W Hobbs ◽  
C Peirce

Summary The seismic velocity of the oceanic crust is a function of its physical properties that include its lithology, degree of alteration, and porosity. Variations in these properties are particularly significant in young crust, but also occur with age as it evolves through hydrothermal circulation and is progressively covered with sediment. While such variation may be investigated through P-wave velocity alone, joint analysis with S-wave velocity allows the determination of Poisson's ratio, which provides a more robust insight into the nature of change in these properties. Here we describe the independent modelling of P- and S-wave seismic datasets, acquired along an ∼330 km-long profile traversing new to ∼8 Myr-old oceanic crust formed at the intermediate-spreading Costa Rica Rift (CRR). Despite S-wave data coverage being almost four-times lower than that of the P-wave dataset, both velocity models demonstrate correlations in local variability and a long-wavelength increase in velocity with distance, and thus age, from the ridge axis of up to 0.8 and 0.6 km s−1, respectively. Using the Vp and Vs models to calculate Poisson's ratio (σ), it reveals a typical structure for young oceanic crust, with generally high values in the uppermost crust that decrease to a minimum of 0.24 by 1.0–1.5 km sub-basement, before increasing again throughout the lower crust. The observed upper crustal decrease in σ most likely results from sealing of fractures, which is supported by observations of a significant decrease in porosity with depth (from ∼15 to < 2 per cent) through the dyke sequence in Ocean Drilling Program borehole 504B. High Poisson's ratio (>0.31) is observed throughout the crust of the north flank of the CRR axis and, whilst this falls within the ‘serpentinite’ classification of lithological proxies, morphological evidence of pervasive surface magmatism and limited tectonism suggests, instead, that the cause is porosity in the form of pervasive fracturing and, thus, that this is the dominant control on seismic velocity in the newly formed CRR crust. South of the CRR, the values of Poisson's ratio are representative of more typical oceanic crust, and decrease with increasing distance from the spreading centre, most likely as a result of mineralisation and increased fracture infill. This is supported by borehole observations and modelled 3-D seismic anisotropy. Crustal segments formed during periods of particularly low half-spreading rate (<35 mm yr−1) demonstrate high Poisson's ratio relative to the background, indicating the likely retention of increased porosity and fracturing associated with the greater degrees of tectonism at the time of their formation. Across the south flank of the CRR, we find that the average Poisson's ratio in the upper 1 km of the crust decreases with age by ∼0.0084 Myr−1 prior to the thermal sealing of the crust, suggesting that, to at least ∼7 Myr, advective hydrothermal processes dominate early CRR-generated oceanic crustal evolution, consistent with heat flow measurements.

Geophysics ◽  
2017 ◽  
Vol 82 (3) ◽  
pp. U61-U73 ◽  
Author(s):  
Laura Valentina Socco ◽  
Cesare Comina

Surface waves (SWs) in seismic records can be used to extract local dispersion curves (DCs) along a seismic line. These curves can be used to estimate near-surface S-wave velocity models. If the velocity models are used to compute S-wave static corrections, the required information consists of S-wave time-average velocities that define the one-way time for a given datum plan depth. However, given the wider use of P-wave reflection seismic with respect to S-wave surveys, the estimate of P-wave time-average velocity would be more useful. We therefore focus on the possibility of also extracting time-average P-wave velocity models from SW dispersion data. We start from a known 1D S-wave velocity model along the line, with its relevant DC, and we estimate a wavelength/depth relationship for SWs. We found that this relationship is sensitive to Poisson’s ratio, and we develop a simple method for estimating an “apparent” Poisson’s ratio profile, defined as the Poisson’s ratio value that relates the time-average S-wave velocity to the time-average P-wave velocity. Hence, we transform the time-average S-wave velocity models estimated from the DCs into the time-average P-wave velocity models along the seismic line. We tested the method on synthetic and field data and found that it is possible to retrieve time-average P-wave velocity models with uncertainties mostly less than 10% in laterally varying sites and one-way traveltime for P-waves with less than 5 ms uncertainty with respect to P-wave tomography data. To our knowledge, this is the first method for reliable estimation of P-wave velocity from SW data without any a priori information or additional data.


2019 ◽  
Vol 23 (3) ◽  
pp. 209-223 ◽  
Author(s):  
Caglar Ozer ◽  
Mehmet Ozyazicioglu

Erzurum and its surroundings are one of the seismically active and hydrothermal areas in the Eastern part of Turkey. This study is the first approach to characterize the crust by seismic features by using the local earthquake tomography method. The earthquake source location and the three dimensional seismic velocity structures are solved simultaneously by an iterative tomographic algorithm, LOTOS-12. Data from a combined permanent network comprising comprises of 59 seismometers which was installed by Ataturk University-Earthquake Research Center and Earthquake Department of the Disaster and Emergency Management Authority  to monitor the seismic activity in the Eastern Anatolia, In this paper, three-dimensional Vp and Vp/Vs characteristics of Erzurum geothermal area were investigated down to 30 km by using 1685 well-located earthquakes with 29.894 arrival times, consisting of 17.298 P- wave and 12.596 S- wave arrivals. We develop new high-resolution depth-cross sections through Erzurum and its surroundings to provide the subsurface geological structure of seismogenic layers and geothermal areas. We applied various size horizontal and vertical checkerboard resolution tests to determine the quality of our inversion process. The basin models are traceable down to 3 km depth, in terms of P-wave velocity models. The higher P-wave velocity areas in surface layers are related to the metamorphic and magmatic compact materials. We report that the low Vp and high Vp/Vs values are observed in Yedisu, Kaynarpinar, Askale, Cimenozu, Kaplica, Ovacik, Yigitler, E part of Icmeler, Koprukoy, Uzunahmet, Budakli, Soylemez, Koprukoy, Gunduzu, Karayazi, Icmesu, E part of Horasan and Kaynak regions indicated geothermal reservoir.


Geophysics ◽  
1995 ◽  
Vol 60 (3) ◽  
pp. 651-659 ◽  
Author(s):  
Mark E. Mathisen ◽  
Paul Cunningham ◽  
Jesse Shaw ◽  
Anthony A. Vasiliou ◽  
J. H. Justice ◽  
...  

S‐wave, P‐wave, and Poisson’s ratio tomograms have been used to interpret the 3-D distribution of rock and fluid properties during an early phase of a California heavy oil sand steamflood. Four lines of good quality crosswell seismic data, with source to receiver offsets ranging from 287 to 551 ft (87 to 168 m), were acquired in a radial pattern around a high temperature cemented receiver cable in four days. Processing, first‐arrival picking, and good quality tomographic reconstructions were completed despite offset‐related variations in data quality between the long and short lines. Interpretation was based on correlations with reservoir models, log, core, temperature, and steam injection data. S‐wave tomograms define the 3-D distribution of the “high flow” turbidite channel facies, the “moderate‐low flow” levee facies, porosity, and structural dip. The S‐wave tomograms also define an area with anomalously low S‐wave velocity, which correlates with low shear log velocities and suggests that pressure‐related dilation and compaction may be imageable. P‐wave tomograms define the same reservoir lithology and structure as the S‐wave tomograms and the 3-D distribution of low compressional velocity zones formed by previous steam‐heat injection and the formation of gas. The low P‐wave velocity zones, which are laterally continuous in the “high flow” channel facies near the top of most zones, indicate that the steam‐heat‐gas distribution is controlled by stratification. The stratigraphic control of gas‐bearing zones inferred from P‐wave tomograms is confirmed by Poisson’s ratio tomograms which display low Poisson’s ratios indicative of gas (<0.35) in the same zones as the low P‐wave velocities. The interpretation results indicate that radial survey tomograms can be tied at a central well and used to develop an integrated 3-D geoscience‐engineering reservoir model despite offset‐related variations in data quality. The laterally continuous, stratification‐controlled, low P‐wave velocity zones, which extend up‐dip, suggest that significant amounts of steam‐heat are not heating the surrounding reservoir volume but are flowing updip along “high flow” channels.


1962 ◽  
Vol 52 (1) ◽  
pp. 95-107
Author(s):  
Otto Nuttli ◽  
John D. Whitmore

Abstract This study is concerned with determining the minimum epicentral distance for which it is permissible to obtain the value of the polarization angle of the S wave by measuring the angle between the great circle path at the station and the direction of the horizontal component of the S wave particle motion obtained from the seismograms. This critical distance can be determined by the fact that at smaller distances the particle motion of the earth's surface due to the incidence of S will be nonlinear (the SH and the horizontal and vertical components of SV will be out of phase with respect to one another) while at larger distances the particle motion will be linear. An analysis of the S motion recorded by the Galitzin-Wilip seismographs at Florissant indicates that the critical distance is 42 degrees. The periods of these S waves are of the order of 10 second. The analysis also shows that the effective P wave velocity of teleseismic waves at the earth's free surface is 7.74 km/sec, and the effective value of Poisson's ratio and the effective S wave velocity at the earth's surface are 0.25 and 4.46 km/sec, respectively. By effective values are meant the values of the velocities and Poisson's ratio that govern the angle of incidence of the waves at the earth's surface.


1991 ◽  
Vol 28 (3) ◽  
pp. 342-354 ◽  
Author(s):  
A. V. Boland ◽  
R. M. Ellis

The Kapuskasing uplift is an oblique cross section of Archean crust exposed by a major thrusting event in Early Proterozoic times. Previous results from the traveltime and amplitude analysis of compressional-wave (P-wave) arrivals from a seismic-refraction experiment have been used to constrain the modelling of shear-wave (S-wave) arrivals and gravity anomalies along the seismic profiles. S-wave and P-wave velocity information have been combined to obtain the variations of Poisson's ratio within the crust. High and low Poisson's ratio values have been linked to the mafic and felsic content, respectively, of the Shield rocks. Density variations along the profiles, constrained by the P-wave velocity structures and the observed gravity anomalies, again have been linked to the lithological variations as observed in the exposed cross section. Geological models, constrained by the geophysical observations and the cross-sectional exposure, have been constructed for profiles across the northern and southern portions of the main uplift region. The results indicate an increase in pyroxene and garnetiferous gneisses with depth in the crust, as suggested by the high P-wave velocities (7.0–7.6 km/s), high densities (3050–3150 kg/m3, high Poisson's ratio values (0.26–0.28), and the petrological variations within the exposure. The presence of a low-velocity and low-density layer of tonalites under the surface greenstones has been established and can account for the low-velocity zones imaged along the Abitibi profile of this experiment and those imaged in other Shield refraction experiments.


1994 ◽  
Vol 31 (7) ◽  
pp. 1052-1063 ◽  
Author(s):  
Matthew H. Salisbury ◽  
David M. Fountain

The compressional (Vp) and shear (Vs) wave velocity structure of the Kapuskasing uplift have been determined as a function of depth, propagation direction, and polarization from laboratory velocity measurements to confining pressures of 600 MPa on oriented samples from known structural levels of the complex. Based on the relative field abundances of the lithologies measured, the three principal terranes exposed in the uplift are characterized at depth by the following average values of Vp, Vs, and apparent Poisson's ratio, σa: (i) Michipicoten greenstone bell (greenschist, depth 0–6 km, Vp = 6.6 km/s, Vs = 3.9 km/s, σa = 0.235); (ii) Wawa gneiss terrane (amphibolite, depth 6–17 km, Vp = 6.5 km/s, Vs = 3.8 km/s, σa = 0.24); and (iii) Kapuskasing structural zone (granulite, depth 17–23 km, Vp = 6.9 km/s, Vs = 3.9 km/s, σa = 0.27). Although anisotropic lithologies such as paragneiss or mafic gneiss are present at all levels and tend to increase in abundance with depth, only in the deepest level (the Kapuskasing zone) are they sufficiently abundant and oriented to produce significant regional seismic anisotropy (transversely isotropic with Vp and Vs fast in the horizontal plane) and detectable shear wave splitting (ΔVs = 0.1 km/s).A comparison between the laboratory data and velocity models determined for the same crustal section from Lithoprobe refraction studies shows excellent agreement, confirming that the lithologies exposed in the Kapuskasing uplift can be projected downdip to the upper–lower crust transition, or Conrad discontinuity, at about 25 km. Below this depth, high P-wave velocities (7.0–7.6 km/s) suggest that the lower crust is more mafic or garnet rich. Similarities between the velocity structure of the Kapuskasing uplift and other sites in the Canadian Shield suggest that the observed crustal section is fairly typical of Archean continental crust.


Geophysics ◽  
2016 ◽  
Vol 81 (4) ◽  
pp. R197-R209 ◽  
Author(s):  
Paolo Bergamo ◽  
Laura Valentina Socco

Surficial formations composed of loose, dry granular materials constitute a challenging target for seismic characterization. They exhibit a peculiar seismic behavior, characterized by a nonlinear seismic velocity gradient with depth that follows a power-law relationship, which is a function of the effective stress. The P- and S-wave velocity profiles are then characterized by a power-law trend, and they can be defined by two power-law exponents [Formula: see text] and two power-law coefficients [Formula: see text]. In case of depth-independent Poisson’s ratio, the P-wave velocity profile can be defined using the [Formula: see text] power-law parameters and Poisson’s ratio. Because body wave investigation techniques (e.g., P-wave tomography) may perform ineffectively on such materials because of high attenuation, we addressed the potential of surface-wave method for a reliable seismic characterization of shallow formations of dry, uncompacted granular materials. We took into account the dependence of seismic wave velocity on effective pressure and performed a multimodal inversion of surface-wave data, which allowed the [Formula: see text] and [Formula: see text] profiles to be retrieved. The method requires the selection of multimodal dispersion curve points referring to surface-wave frequency components traveling within the granular media formation and their inversion for the S-wave power-law parameters and Poisson’s ratio. We have tested our method on a synthetic dispersion curve and applied it to a real data set. In both cases, the surficial layer was made of loose dry sand. The test on the synthetic data set confirmed the reliability of the proposed procedure because the thickness and the [Formula: see text], [Formula: see text] profiles of the sand layer were correctly estimated. For the real data, the outcomes were validated by other geophysical measurements conducted at the same site and they were in agreement with similar studies regarding loose sand formations.


Geophysics ◽  
2000 ◽  
Vol 65 (2) ◽  
pp. 559-564 ◽  
Author(s):  
Ran Bachrach ◽  
Jack Dvorkin ◽  
Amos M. Nur

We determined P- and S-wave velocity depth profiles in shallow, unconsolidated beach sand by analyzing three‐component surface seismic data. P- and S-wave velocity profiles were calculated from traveltime measurements of vertical and tangential component seismograms, respectively. The results reveal two discrepancies between theory and data. Whereas both velocities were found to be proportional to the pressure raised to the power of 1/6, as predicted by the Hertz‐Mindlin contact theory, the actual values of the velocities are less than half of those calculated from this theory. We attribute this discrepancy to the angularity of the sand grains. Assuming that the average radii of curvature at the grain contacts are smaller than the average radii of the grains, we modify the Hertz‐Mindlin theory accordingly. We found that the ratio of the contact radius to the grain radius is about 0.086. The second disparity is between the observed Poisson’s ratio of 0.15 and the theoretical value (0.008 for random pack of quartz spheres). This discrepancy can be reconciled by assuming slip at the grain contacts. Because slip decreases the shearing between grains, Poisson’s ratio increases.


Geophysics ◽  
1982 ◽  
Vol 47 (5) ◽  
pp. 819-824 ◽  
Author(s):  
Harsh K. Gupta ◽  
Ronald W. Ward ◽  
Tzeu‐Lie Lin

Analysis of P‐ and S‐waves from shallow microearthquakes in the vicinity of The Geysers geothermal area, California, recorded by a dense, telemetered seismic array operated by the U.S. Geological Survey (USGS) shows that these phases are easily recognized and traced on record sections to distances of 80 km. Regional average velocities for the upper crust are estimated to be [Formula: see text] and [Formula: see text] for P‐ and S‐waves, respectively. Poisson’s ratio is estimated at 23 locations using Wadati diagrams and is found to vary from 0.13 to 0.32. In general, the Poisson’s ratio is found to be lower at the locations close to the steam production zones at The Geysers and Clear Lake volcanic field to the northeast. The low Poisson ratio corresponds to a decrease in P‐wave velocity in areas of high heat flow. The decrease may be caused by fracturing of the rock and saturation with gas or steam.


Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5007
Author(s):  
Stian Rørheim ◽  
Mohammad Hossain Bhuiyan ◽  
Andreas Bauer ◽  
Pierre Rolf Cerasi

Carbon capture and storage (CCS) by geological sequestration comprises a permeable formation (reservoir) for CO2 storage topped by an impermeable formation (caprock). Time-lapse (4D) seismic is used to map CO2 movement in the subsurface: CO2 migration into the caprock might change its properties and thus impact its integrity. Simultaneous forced-oscillation and pulse-transmission measurements are combined to quantify Young’s modulus and Poisson’s ratio as well as P- and S-wave velocity changes in the absence and in the presence of CO2 at constant seismic and ultrasonic frequencies. This combination is the laboratory proxy to 4D seismic because rock properties are monitored over time. It also improves the understanding of frequency-dependent (dispersive) properties needed for comparing in-situ and laboratory measurements. To verify our method, Draupne Shale is monitored during three consecutive fluid exposure phases. This shale appears to be resilient to CO2 exposure as its integrity is neither compromised by notable Young’s modulus and Poisson’s ratio nor P- and S-wave velocity changes. No significant changes in Young’s modulus and Poisson’s ratio seismic dispersion are observed. This absence of notable changes in rock properties is attributed to Draupne being a calcite-poor shale resilient to acidic CO2-bearing brine that may be a suitable candidate for CCS.


Sign in / Sign up

Export Citation Format

Share Document