scholarly journals On the Effect of CO2 on Seismic and Ultrasonic Properties: A Novel Shale Experiment

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5007
Author(s):  
Stian Rørheim ◽  
Mohammad Hossain Bhuiyan ◽  
Andreas Bauer ◽  
Pierre Rolf Cerasi
Keyword(s):  
Young’S Modulus ◽  
Wave Velocity ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Co2 Storage ◽  
Poisson's Ratio ◽  
Rock Properties ◽  
S Wave ◽  
Velocity Changes ◽  
4D Seismic

Carbon capture and storage (CCS) by geological sequestration comprises a permeable formation (reservoir) for CO2 storage topped by an impermeable formation (caprock). Time-lapse (4D) seismic is used to map CO2 movement in the subsurface: CO2 migration into the caprock might change its properties and thus impact its integrity. Simultaneous forced-oscillation and pulse-transmission measurements are combined to quantify Young’s modulus and Poisson’s ratio as well as P- and S-wave velocity changes in the absence and in the presence of CO2 at constant seismic and ultrasonic frequencies. This combination is the laboratory proxy to 4D seismic because rock properties are monitored over time. It also improves the understanding of frequency-dependent (dispersive) properties needed for comparing in-situ and laboratory measurements. To verify our method, Draupne Shale is monitored during three consecutive fluid exposure phases. This shale appears to be resilient to CO2 exposure as its integrity is neither compromised by notable Young’s modulus and Poisson’s ratio nor P- and S-wave velocity changes. No significant changes in Young’s modulus and Poisson’s ratio seismic dispersion are observed. This absence of notable changes in rock properties is attributed to Draupne being a calcite-poor shale resilient to acidic CO2-bearing brine that may be a suitable candidate for CCS.

scholarly journals Discrepancy between measured dynamic poroelastic parameters and predicted values from Wyllie’s equation for water-saturated Istebna sandstone

2021 ◽  
Author(s):  
Dariusz Knez ◽  
Herimitsinjo Rajaoalison
Keyword(s):  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Laboratory Data ◽  
Confining Pressure ◽  
P Wave ◽  
Poisson's Ratio ◽  
Rock Properties ◽  
Biot’S Coefficient ◽  
Water Saturated

AbstractThe drilling-related geomechanics requires a better understanding of the encountered formation properties such as poroelastic parameters. This paper shows set of laboratory results of the dynamic Young’s modulus, Poisson’s ratio, and Biot’s coefficient for dry and water-saturated Istebna sandstone samples under a series of confining pressure conditions at two different temperatures. The predicted results from Wyllie’s equation were compared to the measured ones in order to show the effect of saturation on the rock weakening. A negative correlation has been identified between Poisson’s ratio, Biot’s coefficient and confining pressure, while a positive correlation between confining pressure and Young’s modulus. The predicted dynamic poroelastic rock properties using the P-wave value from Wyllie’s equation are different from measured ones. It shows the important influence of water saturation on rock strength, which is confirmed by unconfined compressive strength measurement. Linear equations have been fitted for the laboratory data and are useful for the analysis of coupled stress and pore pressure effects in geomechanical problems. Such results are useful for many drilling applications especially in evaluation of such cases as wellbore instability and many other drilling problems.

scholarly journals Feasibility Study on the Application of Dynamic Elastic Rock Properties from Well Log for Shale Hydrocarbon Development of Brownshale Formation in the Bengkalis Trough, Central Sumatra Basin, Indonesia.

2021 ◽  
Vol 6 (2) ◽  
pp. 81-85
Author(s):  
Ahmad Muraji Suranto ◽  
Aris Buntoro ◽  
Carolus Prasetyadi ◽  
Ricky Adi Wibowo
Keyword(s):  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Well Logs ◽  
Poisson's Ratio ◽  
Rock Properties ◽  
Well Log ◽  
Log Data ◽  
Core Data ◽  
Elastic Rock

In modeling the hydraulic fracking program for unconventional reservoir shales, information about elasticity rock properties is needed, namely Young's Modulus and Poisson's ratio as the basis for determining the formation depth interval with high brittleness. The elastic rock properties (Young's Modulus and Poisson's ratio) are a geomechanical parameters used to identify rock brittleness using core data (static data) and well log data (dynamic data). A common problem is that the core data is not available as the most reliable data, so well log data is used. The principle of measuring elastic rock properties in the rock mechanics lab is very different from measurements with well logs, where measurements in the lab are in high stresses / strains, low strain rates, and usually drained, while measurements in well logging use the principle of measured downhole by high frequency sonic. vibrations in conditions of very low stresses / strains, High strain rate, and Always undrained. For this reason, it is necessary to convert dynamic to static elastic rock properties (Poisson's ratio and Young's modulus) using empirical equations. The conversion of elastic rock properties (well logs) from dynamic to static using the empirical calculation method shows a significant shift in the value of Young's Modulus and Poisson's ratio, namely a shift from the ductile zone dominance to the dominant brittle zone. The conversion results were validated with the rock mechanical test results from the analog outcrop cores (static) showing that the results were sufficiently correlated based on the distribution range.

Determination of Poisson's Ratio of Thin low-k Films using Bidirectional Thermal Expansion Measurement

2006 ◽  
Vol 914 ◽  
Author(s):  
Jiping Ye ◽  
Satoshi Shimizu ◽  
Shigeo Sato ◽  
Nobuo Kojima ◽  
Junnji Noro
Keyword(s):  
Thermal Expansion ◽  
Temperature Gradient ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Silicon Oxide ◽  
Young's Modulus ◽  
Polymer Materials ◽  
Poisson's Ratio ◽  
Thermal Expansion Measurement ◽  
Low K

AbstractA recently developed bidirectional thermal expansion measurement (BTEM) method was applied to different types of low-k films to substantiate the reliability of the Poisson's ratio found with this technique and thereby to corroborate its practical utility. In this work, the Poisson's ratio was determined by obtaining the temperature gradient of the biaxial thermal stress from substrate curvature measurements, the temperature gradient of the whole thermal expansion strain along the film thickness from x-ray reflectivity (XRR) measurements, and reduced modulus of the film from nanoindentation measurements. For silicon oxide-based SiOC film having a thickness of 382.5 nm, the Poisson's ratio, Young's modulus and thermal extension coefficient (TEC) were determined to be Vf = 0.26, αf =21 ppm/K and Ef =9,7 GPa. These data are close to the levels of metals and polymers rather than the levels of fused silicon oxide, which is characterized by Vf = 0.17 and Er = 69.6 GPa. The alkyl component in the silicon oxide-based framework is thought to act as an agent in reducing the modulus and elevating the Poisson's ratio in SiOC low-k materials. In the case of an organic polymer SiLK film with a thickness of 501.5 nm, the Poisson's ratio, Young's modulus and TEC were determined to be Vf = 0.39, αf =74 ppm/K and Er =3.1 GPa, which are in the typical range of V= 0.34~0.47 with E =1.0~10 GPa for polymer materials. From the viewpoint of the relationship between the Poisson's ratio and Young's modulus as classified by different material types, the Poisson's ratios found for the silicon oxide-based SiOC and organic SiLK films are reasonable values, thereby confirming that BTEM is a reliable and effective method for evaluating the Poisson's ratio of thin films.

Measurement of Young's Modulus and Poisson's Ratio of Thin Film by Combination of Bulge Test and Nano-Indentation

2008 ◽  
Vol 33-37 ◽  
pp. 969-974 ◽  
Author(s):  
Bong Bu Jung ◽  
Seong Hyun Ko ◽  
Hun Kee Lee ◽  
Hyun Chul Park
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Applied Pressure ◽  
Indentation Test ◽  
Poisson's Ratio ◽  
Bulge Test ◽  
Nano Indentation

This paper will discuss two different techniques to measure mechanical properties of thin film, bulge test and nano-indentation test. In the bulge test, uniform pressure applies to one side of thin film. Measurement of the membrane deflection as a function of the applied pressure allows one to determine the mechanical properties such as the elastic modulus and the residual stress. Nano-indentation measurements are accomplished by pushing the indenter tip into a sample and then withdrawing it, recording the force required as a function of position. . In this study, modified King’s model can be used to estimate the mechanical properties of the thin film in order to avoid the effect of substrates. Both techniques can be used to determine Young’s modulus or Poisson’s ratio, but in both cases knowledge of the other variables is needed. However, the mathematical relationship between the modulus and Poisson's ratio is different for the two experimental techniques. Hence, achieving agreement between the techniques means that the modulus and Poisson’s ratio and Young’s modulus of thin films can be determined with no a priori knowledge of either.

Multi-Parameter Optimization to Improve the Erosion Resistance of Coating by Fe Simulation

2021 ◽  
Author(s):  
Fang Li ◽  
Liuxi Cai ◽  
Shun-sen Wang ◽  
Zhenping Feng
Keyword(s):  
Tensile Stress ◽  
Young’S Modulus ◽  
Impact Velocity ◽  
Coating Thickness ◽  
Poisson’S Ratio ◽  
Erosion Resistance ◽  
Young's Modulus ◽  
Tio2 Coating ◽  
Poisson's Ratio ◽  
Stress Peak

Abstract Finite element method (FEM) was used to study the stress peak of stress S11 (Radial stress component in X-axis) on the steam turbine blade surface of four typical erosion-resistant coatings (Fe2B, CrN, Cr3C2-NiCr and Al2O3-13%TiO2). The effect of four parameters, such as impact velocity, coating thickness, Young's modulus and Poisson's ratio on the stress peak of stress S11 were analyzed. Results show that: the position of tensile stress peak and compressive stress peak of stress S11 are far away from the impact center point with the increase of impact velocity. When coating thickness is equal to or greater than 10μm, the magnitude of tensile stress peak of stress S11 on the four coating surfaces does not change with the coating thickness at different impact velocities. When coating thickness is equal to or greater than 2μm, the magnitude of tensile stress peak of stress S11 of four coatings show a trend of increasing first and then decreasing with the increase of Young's modulus. Meanwhile, the larger the Poisson's ratio, the smaller the tensile stress peak of stress S11. After optimization, When coating thickness is 2μm, Poisson's ratio is 0.35 and Young's modulus is 800 GPa, the Fe2B coating has the strongest erosion resistance under the same impact conditions, followed by Cr3C2-NiCr, CrN, and the Al2O3- 13%TiO2 coating, Al2O3-13%TiO2 coating has the worst erosion resistance.

Sign in / Sign up

Export Citation Format

Share Document