Photonic curing of silver paths on 3D printed polymer substrate

Circuit World ◽  
2019 ◽  
Vol 45 (1) ◽  
pp. 9-14
Author(s):  
Jakub Krzeminski ◽  
Bartosz Blicharz ◽  
Andrzej Skalski ◽  
Grzegorz Wroblewski ◽  
Małgorzata Jakubowska ◽  
...  
Keyword(s):  
Polymer Substrate ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Photonic Curing ◽  
Structural Electronics ◽  
Jet Printing ◽  
3D Printed ◽  
Aerosol Jet Printing ◽  
Photonic Sintering

Purpose Despite almost limitless possibilities of rapid prototyping, the idea of 3D printed fully functional electronic device still has not been fulfilled – the missing point is a highly conductive material suitable for this technique. The purpose of this paper is to present the usage of the photonic curing process for sintering highly conductive paths printed on the polymer substrate. Design/methodology/approach This paper evaluates two photonic curing processes for the conductive network formulation during the additive manufacturing process. Along with the xenon flash sintering for aerosol jet-printed paths, this paper examines rapid infrared sintering for thick-film and direct write techniques. Findings This paper proves that the combination of fused deposition modeling, aerosol jet printing or paste deposition, along with photonic sintering, is suitable to obtain elements with low resistivity of 3,75·10−8 Ωm. Presented outcomes suggest the solution for fabrication of the structural electronics systems for daily-use applications. Originality/value The combination of fused deposition modelling (FDM) and aerosol jet printing or paste deposition used with photonic sintering process can fill the missing point for highly conductive materials for structural electronics.

Use of polymer concrete for large-scale 3D printing

2021 ◽  
Vol 27 (3) ◽  
pp. 465-474
Author(s):  
Martin Krčma ◽  
David Škaroupka ◽  
Petr Vosynek ◽  
Tomáš Zikmund ◽  
Jozef Kaiser ◽  
...  
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Mechanical Performance ◽  
Construction Material ◽  
Polymer Concrete ◽  
Fused Deposition Modelling ◽  
Cast State ◽  
Content Type ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the evaluation of a polymer concrete as a three-dimensional (3D) printing material. An associated company has developed plastic concrete made from reused unrecyclable plastic waste. Its intended use is as a construction material. Design/methodology/approach The concrete mix, called PolyBet, composed of polypropylene and glass sand, is printed by the fused deposition modelling process. The process of material and parameter selection is described. The mechanical properties of the filled material were compared to its cast state. Samples were made from castings and two different orientations of 3D-printed parts. Three-point flex tests were carried out, and the area of the break was examined. Computed tomography of the samples was carried out. Findings The influence of the 3D printing process on the material was evaluated. The mechanical performance of the longitudinal samples was close to the cast state. There was a difference in the failure mode between the states, with cast parts exhibiting a tougher behaviour, with fractures propagating in a stair-like manner. The 3D-printed samples exhibited high degrees of porosity. Originality/value The results suggest that the novel material is a good fit for 3D printing, with little to no degradation caused by the process. Layer adhesion was shown to be excellent, with negligible effect on the finished part for the longitudinal orientation. That means, if large-scale testing of buildability is successful, the material is a good fit for additive manufacturing of building components and other large-scale structures.

Mechanical properties and water absorption of surface modified ABS 3D printed by fused deposition modelling

2018 ◽  
Vol 24 (1) ◽  
pp. 195-203 ◽  
Author(s):  
Marco Leite ◽  
André Varanda ◽  
António Relógio Ribeiro ◽  
Arlindo Silva ◽  
Maria Fátima Vaz
Keyword(s):  
Mechanical Properties ◽  
Absorption Coefficient ◽  
Water Absorption ◽  
Dimensional Stability ◽  
Open Porosity ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Tension Properties ◽  
3D Printed

Purpose The purpose of this paper is to investigate the effect of a sealing protective treatment on the water absorption and mechanical properties of acrylonitrile butadiene styrene (ABS)-printed parts by fused deposition modelling. Protective products include aqueous acetone solutions with different concentrations, polyurethane wood sealer and aqueous acrylic-based varnish. Design/methodology/approach Open porosity was estimated by the absorption coefficient and the total amount of water retained, obtained from water absorption tests. Mechanical characterization was performed by compressive and tensile tests. Different specimens with different build directions and raster angles were used. Findings The treatments with acetone solutions were not effective in reducing the porosity of ABS parts, as the amount of acetone that reduces effectively the porosity will also affect the sample dimensional stability. The polyurethane treatment was found to reduce the absorption coefficient, but the maximum water content and the open porosity remain almost unchanged in comparison with the ones obtained for untreated specimens. The treatment with an acrylic-based varnish was found to preserve the dimensional stability of the specimens, to reduce the open porosity and to maintain the compression and tension properties of the specimens in different build directions and raster angles. Originality/value Surface modification for water tight applications of ABS 3D printing parts enables new designs where both sealing and the preservation of mechanical properties are important. As per the knowledge of the authors, the water absorption and the mechanical behaviour of ABS 3D printed parts, before and after treatment, were not previously investigated.

FDM 3D printing method utility assessment in small RC aircraft design

2019 ◽  
Vol 91 (6) ◽  
pp. 865-872 ◽  
Author(s):  
Igor Skawiński ◽  
Tomasz Goetzendorf-Grabowski
Keyword(s):  
3D Printing ◽  
Aircraft Design ◽  
Cost Effective ◽  
Fused Deposition Modelling ◽  
Thin Wall ◽  
Good Reliability ◽  
Content Type ◽  
Fused Deposition ◽  
Wall Structures ◽  
3D Printed

Purpose The purpose of this paper is to investigate the possibility of manufacturing fused deposition modelling (FDM) 3D printed structures such as wings or fuselages for small remote control (RC) air craft and mini unmaned aerial vehicles (UAVs). Design/methodology/approach Material tests, design assumptions and calculations were verified by designing and manufacturing a small radio-controlled motor-glider using as many printed parts as possible and performing test flights. Findings It is possible to create an aircraft with good flight characteristics using FDM 3D printed parts. Current level of technology allows for reasonably fast manufacturing of 3D printed aircraft with good reliability and high success ratio of prints; however, only some of the materials are suitable for printing thin wall structures such as wings. Practical implications The paper proves that apart from currently popular small RC aircraft structural materials such as composites, wood and foam, there is also printed plastic. Moreover, 3D printing is highly competitive in some aspects such as first unit production time or production cost. Originality/value The presented manufacturing technique can be useful for quick and cost-effective creating scale prototypes of the aircraft for performing test flights.

Optimal assembling of 3D printed features by modulation of interfacial behaviour

2019 ◽  
Vol 25 (1) ◽  
pp. 13-21
Author(s):  
Justin Favero ◽  
Sofiane Belhabib ◽  
Sofiane Guessasma ◽  
Hedi Nouri
Keyword(s):  
Design Methodology ◽  
Acrylonitrile Butadiene Styrene ◽  
Interfacial Phenomena ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Interfacial Behaviour ◽  
3D Printed ◽  
Practical Implications ◽  
Butadiene Styrene

Purpose Assembling items to achieve bigger parts seems to be the solution to counterbalance the dimension limits of 3D printing. This work aims to propose an approach to achieve optimal assembling. Design/methodology/approach Acrylonitrile butadiene styrene polymer samples were printed using fused deposition modelling (FDM). These samples were assembled and the precise contribution of interfacial shearing and tension was measured using simple tensile experiments. Findings The results achieved show the correlation between the printing orientation and the assembling angle. It could be proved that rupture by an interfacial decohesion mechanism of glued parts can be avoided by simple adaptation of the assembling junction. Practical implications Design of large parts using FDM is no more a limitation if assembling configurations are adapted based on the knowledge gained about the interfacial phenomena occurring at the junction position. Originality/value The unbalanced contribution of shearing and tension at the interface defines new assembling profiles that exclude flat junctions.

Analysis of the influence of polylactic acid (PLA) colour on FDM 3D printing temperature and part finishing

2018 ◽  
Vol 24 (8) ◽  
pp. 1305-1316 ◽  
Author(s):  
Juliana Breda Soares ◽  
João Finamor ◽  
Fabio Pinto Silva ◽  
Liane Roldo ◽  
Luis Henrique Cândido
Keyword(s):  
Polylactic Acid ◽  
Three Dimensional ◽  
Mechanical Analysis ◽  
Fused Deposition Modelling ◽  
Process Conditions ◽  
Content Type ◽  
3D Print ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to analyse the effect of different polylactic acid (PLA) colours used on fused deposition modelling (FDM), considering the product finishing quality produced with the same process conditions. Design/methodology/approach The methodology adopted was to design a virtual modelling object and three-dimensional (3D) print it with FDM with different PLA colours (natural, green and black), using the same parameters. 3D scanning and scanning electron microscopy was used to analyse the model finishing of each sample. Fourier-transform infrared spectroscopy analysis, thermogravimetric analysis and dynamic mechanical analysis were used to characterize the material and verify if the colour affected its thermal behaviour. Findings Findings showed that different PLA colours lead to distinct 3D printed finishings under the same process conditions. Thermal analysis showed a reason for the printing finishing difference. The degradation temperatures and the glass temperatures vary depending on the PLA colour. This affects the FDM working temperature. Originality/value This study will contribute to improving the finishing quality of 3D printed products by collaborating to the determination of its process conditions.

scholarly journals Review of Materials and Fabrication Methods for Flexible Nano and Micro-Scale Physical Property Sensors

2021 ◽  
Author(s):  
Anesu Nyabadza ◽  
Mercedes Vázquez ◽  
Shirley Coyle ◽  
Brian Fitzpatrick ◽  
Dermot Brabazon
Keyword(s):  
Food Packaging ◽  
Physical Property ◽  
Fused Deposition Modelling ◽  
Self Healing ◽  
Operating Life ◽  
Flexible Sensors ◽  
Fused Deposition ◽  
Copper Manganese ◽  
Jet Printing ◽  
Aerosol Jet Printing

The use of flexible sensors has tripled over the last decade due to the increased demand in various fields including health monitoring, food packaging, electronic skins and soft robotics. Flexible sensors have the ability to be bent and stretched during use and can still maintain their electrical and mechanical properties. This gives them an advantage over rigid sensors that lose their sensitivity when subject to bending. Advancements in 3D printing have enabled the development of tailored flexible sensors. Various additive manufacturing methods are being used to develop these sensors including inkjet printing, aerosol jet printing, fused deposition modelling, direct ink writing, selective laser melting and others. Hydrogels have gained much attention in the literature due to their self-healing and shape transforming. Self-healing enables the sensor to recover from damages such as cracks and cuts incurred during use and this enables the sensor to have a longer operating life and stability. Various polymers are used as substrates on which the sensing conductive material is placed. Polymers including polydimethylsiloxane (PDMS), polyvinyl acetate (PVA), and Kapton are extensively used in flexible sensors. The most widely used nanomaterials in flexible sensors are carbon and silver, however, other nanomaterials such as iron, copper, manganese dioxide and gold are also used to provide controlled levels of conductivity or other functional properties.

Effect of fused deposition modelling process parameters on mechanical properties of 3D printed parts

2019 ◽  
Vol 16 (4) ◽  
pp. 550-559 ◽  
Author(s):  
Abhinav Chadha ◽  
Mir Irfan Ul Haq ◽  
Ankush Raina ◽  
Rana Ratna Singh ◽  
Narendra Babu Penumarti ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Layer Thickness ◽  
Process Parameters ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Primary Layer ◽  
Bed Temperature ◽  
3D Printed

Purpose This paper aims to explore the effect of bed temperature, primary layer thickness and infill pattern (rectilinear, honeycomb, triangular) on the mechanical properties of tensile strength and bending strength of 3D printed parts. Design/methodology/approach Samples in accordance to various ASTM standards were printed by fused deposition modelling (FDM) method by varying the various input paramaters such as bed temperature, primary layer thickness and infill pattern (rectilinear, honeycomb, triangular). Tensile and bending testing was carried out on the printed parts, and post to the testing, fractography has been carried out using scanning electron microscope. Findings With increase in bed temperature tensile strength and flexural strength first increases then decreases. With the increase in primary layer thickness, tensile strength and flexural strength increase. With regard to infill patterns, triangular and honeycomb exhibit better tensile strength and better flexural strength. Practical implications The 3D printing is increasingly becoming important for manufacturing of engineering parts, determining the process parameters which could result in better mechanical and physical properties shall certainly help designers and manufacturers globally. Originality/value This work elucidates the effect of various process parameters of FDM on tensile and flexural properties of the samples.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

Investigations of process parameters during dissolution studies of drug loaded 3D printed tablets

2021 ◽  
pp. 095441192199358
Author(s):  
Varun Sharma ◽  
Khaja Moinuddin Shaik ◽  
Archita Choudhury ◽  
Pramod Kumar ◽  
Prateek Kala ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Process Parameters ◽  
Empirical Relation ◽  
Three Dimensional ◽  
Critical Parameters ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Rate Of Dissolution ◽  
3D Printed ◽  
Percentage Release

The present research paper attempts to study the effect of different process parameters on the dissolution rate during 3D printed tablets. Three-dimensional printing has the potential of serving tailored made tablets to cater personalized drug delivery systems. Fluorescein loaded PVA filaments through impregnation route was used to fabricate tablets based on Taguchi based design of experimentation using Fused Deposition Modelling (FDM). The effect of print speed, infill percentage and layer thickness were analyzed to study the effect on rate of dissolution. Infill percentage followed by print speed were found to be critical parameters affecting dissolution rate. The data analysis provided an insight into the study of interaction among different 3D printing parameters to develop an empirical relation for percentage release of the drug in human body.

Sign in / Sign up

Export Citation Format

Share Document