Investigations of process parameters during dissolution studies of drug loaded 3D printed tablets

2021 ◽  
pp. 095441192199358
Author(s):  
Varun Sharma ◽  
Khaja Moinuddin Shaik ◽  
Archita Choudhury ◽  
Pramod Kumar ◽  
Prateek Kala ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Process Parameters ◽  
Empirical Relation ◽  
Three Dimensional ◽  
Critical Parameters ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Rate Of Dissolution ◽  
3D Printed ◽  
Percentage Release

The present research paper attempts to study the effect of different process parameters on the dissolution rate during 3D printed tablets. Three-dimensional printing has the potential of serving tailored made tablets to cater personalized drug delivery systems. Fluorescein loaded PVA filaments through impregnation route was used to fabricate tablets based on Taguchi based design of experimentation using Fused Deposition Modelling (FDM). The effect of print speed, infill percentage and layer thickness were analyzed to study the effect on rate of dissolution. Infill percentage followed by print speed were found to be critical parameters affecting dissolution rate. The data analysis provided an insight into the study of interaction among different 3D printing parameters to develop an empirical relation for percentage release of the drug in human body.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

scholarly journals 3D Printing of Thermo-Sensitive Drugs

Pharmaceutics ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1524
Author(s):  
Sadikalmahdi Abdella ◽  
Souha H. Youssef ◽  
Franklin Afinjuomo ◽  
Yunmei Song ◽  
Paris Fouladian ◽  
...  
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Future Directions ◽  
Digital Light Processing ◽  
Fused Deposition ◽  
Printing Technique ◽  
3D Printed ◽  
Semi Solid ◽  
Selection Of

Three-dimensional (3D) printing is among the rapidly evolving technologies with applications in many sectors. The pharmaceutical industry is no exception, and the approval of the first 3D-printed tablet (Spiratam®) marked a revolution in the field. Several studies reported the fabrication of different dosage forms using a range of 3D printing techniques. Thermosensitive drugs compose a considerable segment of available medications in the market requiring strict temperature control during processing to ensure their efficacy and safety. Heating involved in some of the 3D printing technologies raises concerns regarding the feasibility of the techniques for printing thermolabile drugs. Studies reported that semi-solid extrusion (SSE) is the commonly used printing technique to fabricate thermosensitive drugs. Digital light processing (DLP), binder jetting (BJ), and stereolithography (SLA) can also be used for the fabrication of thermosensitive drugs as they do not involve heating elements. Nonetheless, degradation of some drugs by light source used in the techniques was reported. Interestingly, fused deposition modelling (FDM) coupled with filling techniques offered protection against thermal degradation. Concepts such as selection of low melting point polymers, adjustment of printing parameters, and coupling of more than one printing technique were exploited in printing thermosensitive drugs. This systematic review presents challenges, 3DP procedures, and future directions of 3D printing of thermo-sensitive formulations.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

scholarly journals Parameters Affecting the Mechanical Properties of Three-Dimensional (3D) Printed Carbon Fiber-Reinforced Polylactide Composites

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2456
Author(s):  
Demei Lee ◽  
Guan-Yu Wu
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Bed Temperature ◽  
3D Printed ◽  
The Impact

Three-dimensional (3D) printing is a manufacturing technology which creates three-dimensional objects layer-by-layer or drop-by-drop with minimal material waste. Despite the fact that 3D printing is a versatile and adaptable process and has advantages in establishing complex and net-shaped structures over conventional manufacturing methods, the challenge remains in identifying the optimal parameters for the 3D printing process. This study investigated the influence of processing parameters on the mechanical properties of Fused Deposition Modelling (FDM)-printed carbon fiber-filled polylactide (CFR-PLA) composites by employing an orthogonal array model. After printing, the tensile and impact strengths of the printed composites were measured, and the effects of different parameters on these strengths were examined. The experimental results indicate that 3D-printed CFR-PLA showed a rougher surface morphology than virgin PLA. For the variables selected in this analysis, bed temperature was identified as the most influential parameter on the tensile strength of CFR-PLA-printed parts, while bed temperature and print orientation were the key parameters affecting the impact strengths of printed composites. The 45° orientation printed parts also showed superior mechanical strengths than the 90° printed parts.

scholarly journals 3D Printing for Hip Implant Applications: A Review

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2682
Author(s):  
Obinna Okolie ◽  
Iwona Stachurek ◽  
Balasubramanian Kandasubramanian ◽  
James Njuguna
Keyword(s):  
3D Printing ◽  
Hip Replacement ◽  
Selective Laser Sintering ◽  
Three Dimensional ◽  
Ceramic Materials ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Replacement Treatment ◽  
Determining Factors ◽  
3D Printed

There is a rising demand for replacement, regeneration of tissues and organ repairs for patients who suffer from diseased/damaged bones or tissues such as hip pains. The hip replacement treatment relies on the implant, which may not always meet the requirements due to mechanical and biocompatibility issues which in turn may aggravate the pain. To surpass these limitations, researchers are investigating the use of scaffolds as another approach for implants. Three-dimensional (3D) printing offers significant potential as an efficient fabrication technique on personalized organs as it is capable of biomimicking the intricate designs found in nature. In this review, the determining factors for hip replacement and the different fabrication techniques such as direct 3D printing, Fused Deposition Modelling (FDM), Selective Laser Sintering (SLS) and stereolithography (SLA) for hip replacement. The study also covers surface modifications of 3D printed implants and provides an overview on 3D tissue regeneration. To appreciate the current conventional hip replacement practices, the conventional metallic and ceramic materials are covered, highlighting their rationale as the material of choice. Next, the challenges, ethics and trends in the implants’ 3D printing are covered and conclusions drawn. The outlook and challenges are also presented here. The knowledge from this review indicates that 3D printing has enormous potential for providing a pathway for a sustainable hip replacement.

scholarly journals Surface Roughness Effect on the 3d Printed Butt Joints Strength

2015 ◽  
Author(s):  
V. Kovan ◽  
G. Altan ◽  
E.S. Topal ◽  
H.E. Camurlu
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Three Dimensional ◽  
Thickness Effect ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Object

Three-dimensional printing or 3D printing (also called additive manufacturing) is any of various processes used to make a three-dimensional object. Fused deposition modelling (FDM) is an additive manufacturing technology commonly used for modelling, prototyping, and production applications. It is one of the techniques used for 3D printing. FDM is somewhat restricted in the size and the variation of shapes that may be fabricated. For parts too large to fit on a single build, for faster job builds with less support material, or for parts with finer features, sectioning and bonding FDM parts is a great solution. The strength of adhesive bonded FDM parts is affected by the surface roughness. In this study, the layer thickness effect on bonding strength is experimentally studied and the results are discussed.

scholarly journals Effect of Autoclave Pressure and Temperature on Consolidation of Layers and Mechanical Properties of Additively Manufactured (FDM) Products with PLA

2021 ◽  
Vol 5 (4) ◽  
pp. 114
Author(s):  
Yousuf Pasha Shaik ◽  
Jens Schuster ◽  
Aarif Shaik ◽  
Mustafa Mohammed ◽  
Harshavardhan Reddy Katherapalli
Keyword(s):  
Mechanical Properties ◽  
Three Dimensional ◽  
Strength Properties ◽  
Post Treatment ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Concentric Pattern ◽  
Raster Angle ◽  
3D Printed ◽  
Manufacturing Technologies

In additive manufacturing technologies, fused deposition modelling (FDM) is continuing its advancement from rapid prototyping to rapid manufacturing. However, effective usage of FDM is not performed due to the poor mechanical properties of the 3D-printed components. This drawback restricts their usage in many applications. Much research, such as reinforcing 3D-printed parts with fibers, changing printing parameters (infill density, infill concentration, extrusion temperature, nozzle diameter, layer thickness, raster angle, etc.) are aimed to increase the mechanical properties of 3D-printed parts. This research paper aims to investigate the effect of pressure and temperature on the mechanical properties and consolidation of layers of 3D-printed PLA (Polylactic Acid). Post-treatment was done using a customized autoclave. Autoclave has the capability to maintain 185 °C and 135 bar pressure. Three-dimensional-printed specimens were manufactured using the FDM process with two patterns. Later, the specimens were subjected to various post-treatment processes, then followed with testing and analysis of mechanical properties. Post-treatment process carried out by placing them in an autoclave at certain pressure and temperature conditions. To investigate the repeatability and tolerances, the test series includes a minimum of four to six test specimens. The results indicate that the concentric pattern yields the most desirable tensile, impact, and flexural strength due to the alignment of deposited rasters and better consolidation of layers with the loading direction. The pressure and temperature of the autoclave has a positive effect on the PLA samples, which helped them to reorganize the structure, hence strength properties were enhanced. The test results also compared with injection-molded samples for better understating.

Analysis of the influence of polylactic acid (PLA) colour on FDM 3D printing temperature and part finishing

2018 ◽  
Vol 24 (8) ◽  
pp. 1305-1316 ◽  
Author(s):  
Juliana Breda Soares ◽  
João Finamor ◽  
Fabio Pinto Silva ◽  
Liane Roldo ◽  
Luis Henrique Cândido
Keyword(s):  
Polylactic Acid ◽  
Three Dimensional ◽  
Mechanical Analysis ◽  
Fused Deposition Modelling ◽  
Process Conditions ◽  
Content Type ◽  
3D Print ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to analyse the effect of different polylactic acid (PLA) colours used on fused deposition modelling (FDM), considering the product finishing quality produced with the same process conditions. Design/methodology/approach The methodology adopted was to design a virtual modelling object and three-dimensional (3D) print it with FDM with different PLA colours (natural, green and black), using the same parameters. 3D scanning and scanning electron microscopy was used to analyse the model finishing of each sample. Fourier-transform infrared spectroscopy analysis, thermogravimetric analysis and dynamic mechanical analysis were used to characterize the material and verify if the colour affected its thermal behaviour. Findings Findings showed that different PLA colours lead to distinct 3D printed finishings under the same process conditions. Thermal analysis showed a reason for the printing finishing difference. The degradation temperatures and the glass temperatures vary depending on the PLA colour. This affects the FDM working temperature. Originality/value This study will contribute to improving the finishing quality of 3D printed products by collaborating to the determination of its process conditions.

On 3D-printed ZnO-reinforced PLA matrix composite: Tensile, thermal, morphological and shape memory characteristics

2020 ◽  
pp. 089270572093596
Author(s):  
Mohit Singh ◽  
Rupinder Singh ◽  
Ranvijay Kumar ◽  
Pawan Kumar ◽  
Pawan Preet
Keyword(s):  
Shape Memory ◽  
Process Parameters ◽  
Maximum Modulus ◽  
Atmospheric Temperature ◽  
Maximum Strength ◽  
Fused Deposition Modelling ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
3D Printed ◽  
Memory Characteristics

The zinc oxide (ZnO)-reinforced polylactic acid (PLA) matrix has established shape memory characteristics. But hitherto little has been reported on two-way programmed 3D-printed ZnO-reinforced PLA functional prototypes (prepared on commercial fused deposition modelling (FDM) set-up). This article reports the effect of 3D printing process parameters on tensile, thermal, morphological and two-way programmed shape memory characteristics of ZnO-reinforced PLA-based functional prototypes. It has been ascertained that the maximum strength at peak (14.32 MPa) and maximum strength at break (12.89 MPa) were observed for sample printed at 80% infill density, four number of perimeters with triangular pattern. Maximum Young’s modulus (233.68 MPa) was observed for samples printed at 80% infill density and three perimeters with honeycomb pattern. Also, the maximum modulus of toughness (0.883 MPa) was observed in case of sample printed at 80% infill density, five perimeters with rectilinear pattern. Further based upon thermal analysis using differential scanning calorimetry, it has been ascertained that there is no significant effect of FDM process parameters on normalized heat capacity of functional prototype. As regards to two-way programmed specimens, it has been observed that the porosity of functional prototypes increase with 30 min immersion in water as stimulus at 70°C and it again decreases (regain) after 30 min exposure at atmospheric temperature. Contrary to this, the samples’ porosity values decrease with 30 min immersion in water at 10°C and regain after 30 min exposure at atmospheric temperature. Further some effect of shape memory has been noticed on functional prototypes volume and weight at two different temperatures.

Sign in / Sign up

Export Citation Format

Share Document