Experimental investigation of zeolite and limestone powder on self-compacting concrete strength after early loading

2019 ◽  
Vol 10 (4) ◽  
pp. 515-533
Author(s):  
Faeze Nejati ◽  
Samira Ahmadi ◽  
S.A. Edalatpanah
Keyword(s):  
Compressive Strength ◽  
High Efficiency ◽  
Precast Concrete ◽  
Concrete Strength ◽  
Construction Materials ◽  
Limestone Powder ◽  
Self Compacting Concrete ◽  
Construction Time ◽  
Content Type ◽  
Curing Conditions

Purpose Modern construction methods have been developed with the goal of reducing construction time as much as possible, which results in some situations during construction and within the first few days after it, when concrete is subjected to exceptionally high loads. The precast concrete, which is the concrete in very early ages, may result in severe cracks or damages. In conventional construction projects, sometimes working with concrete, which had not reached its ultimate strength, is an unavoidable matter of fact. This paper aims to discuss these issues. Design/methodology/approach Researchers in the field of construction materials have done their best to make some changes in the different parts of the concrete in order to bring about reforms, based on the existing needs, and achieve new quality and primacy from concrete. One kind of concrete, the emergence of which dates back to many years ago, is self-compacting concrete. Thanks to its high efficiency for the parts with complex forms of high-density steel, this kind of concrete suggests new prospects. Findings This study aims at evaluating the effect of early loads on the 28-day compressive strength of concretes with zeolite and limestone powder under different curing conditions (wet or dry). In this regard, two self-compacting concrete mix designs with the same ratio of water to cementations materials and 0.4 percent and 10 percent zeolite have been considered; therefore, concrete cube samples with zeolite and limestone powder in different curing conditions at ages of three, one and seven days under preloading with 80–90 percent of compressive strength are damaged, and after curing in different conditions, their 28-day compressive strength is measured. According to the results, the recovery of the 28-day compressive strength of damaged samples, compared to that of intact samples, is possible in all curing conditions. The experiments that have been performed on concrete samples under dry and wet curing conditions show that the full recovery of compressive strength of damaged samples compared to that of intact ones happened only in preloaded samples at the age of one days, and in other ages (three and seven days) the 28-day strength reduction has occurred in damaged samples compared to the that in intact samples. The results of concrete samples with zeolite and without limestone powder at the age of one day indicate the greatest impact on other samples on the 28-day compressive strength of damaged samples compared to that of intact ones, occurring under dry condition. Originality/value This research analyzed and studied the influence under wet and dry curing conditions and the presence of limestone powder and zeolite fillers in recovering of the 28-day compressive strength of preloaded concrete samples at early stages (one, three and seven days) after the construction of the concrete.

scholarly journals Effect of internal curing on performance of self-compacting concrete by using sustainable materials

2018 ◽  
Vol 162 ◽  
pp. 02017
Author(s):  
Nada Aljalawi ◽  
Amar Yahia AL-Awadi
Keyword(s):  
Compressive Strength ◽  
Lightweight Aggregate ◽  
Internal Curing ◽  
Modulus Of Rupture ◽  
Limestone Powder ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Self Compacting Concrete ◽  
Curing Conditions ◽  
Compressive Strength Test

This paper is devoted to investigate the effect of internal curing technique on the properties of self-compacting concrete. In this study, self-compacting concrete is produced by using limestone powder as partial replacement by weight of cement with percentage of (5%), sand is partially replaced by volume with saturated fine lightweight aggregate which is thermostone aggregate as internal curing material in three percentages of (5%, 10%, 15%) for self-compacting concrete, and the use of two external curing conditions which are water and air. The experimental work was divided into three parts: in the first part, the workability tests of fresh self-compacting concrete were conducted. The second part included conducting compressive strength test and modulus of rupture test at ages of (7, 28 and 90) days. The third part included doing the shrinkage test at age of (7, 14, 21, 28) days. The results show that internally cured self-compacting concrete has the best workability and the best properties of hardened concrete which include (compressive strength, modulus of rupture) of externally cured self-compacting concrete with both water and air as compared with reference concretes. Also, the hardened properties of internally cured self-compacting concrete with percentage of (5%) with thermostone aggregate is the best as compared with that of percentages (10% and 15%) in both external curing conditions. In general, the results of shrinkage test have shown reduction in shrinkage of internally cured self-compacting concrete as compared with reference concretes and this reduction increases with increase in the thermostone aggregate content-within-self-compacting-concrete.

scholarly journals Evaluation of Self-Compacting Concrete Strength with Non-Destructive Tests for Concrete Structures

2019 ◽  
Vol 9 (23) ◽  
pp. 5109 ◽  
Author(s):  
Miguel C. S. Nepomuceno ◽  
Luís F. A. Bernardo
Keyword(s):  
Compressive Strength ◽  
Concrete Strength ◽  
Surface Hardness ◽  
Pulse Velocity ◽  
Concrete Compressive Strength ◽  
Self Compacting Concrete ◽  
Coarse Aggregates ◽  
Pull Out ◽  
Concrete Maturity ◽  
Non Destructive

Self-compacting concrete (SCC) shows to have some specificities when compared to normal vibrated concrete (NVC), namely higher cement paste dosage and smaller volume of coarse aggregates. In addition, the maximum size of coarse aggregates is also reduced in SCC to prevent blocking effect. Such specificities are likely to affect the results of non-destructive tests when compared to those obtained in NVC with similar compressive strength and materials. This study evaluates the applicability of some non-destructive tests to estimate the compressive strength of SCC. Selected tests included the ultrasonic pulse velocity test (PUNDIT), the surface hardness test (Schmidt rebound hammer type N), the pull-out test (Lok-test), and the concrete maturity test (COMA-meter). Seven sets of SCC specimens were produced in the laboratory from a single mixture and subjected to standard curing. The tests were applied at different ages, namely: 1, 2, 3, 7, 14, 28, and 94 days. The concrete compressive strength ranged from 45 MPa (at 24 h) to 97 MPa (at 94 days). Correlations were established between the non-destructive test results and the concrete compressive strength. A test variability analysis was performed and the 95% confidence limits for the obtained correlations were computed. The obtained results for SCC showed good correlations between the concrete compressive strength and the non-destructive tests results, although some differences exist when compared to the correlations obtained for NVC.

scholarly journals Effect of Curing Method on Properties of Lightweight Foamed Concrete

2018 ◽  
Vol 7 (2.29) ◽  
pp. 927 ◽  
Author(s):  
Bishir Kado ◽  
Shahrin Mohammad ◽  
Yeong Huei Lee ◽  
Poi Ngian Shek ◽  
Mariyana Aida Ab Kadir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Precast Concrete ◽  
Construction Materials ◽  
Splitting Tensile Strength ◽  
Structural Members ◽  
Lightweight Construction ◽  
Foamed Concrete ◽  
Curing Method

Lightweight construction is aimed to achieve a sustainable feature by reducing transportation frequency and construction materials usage during construction phase. Lightweight precast concrete may serve an alternative for the lightweight construction. There are rarely application can be found for structural members as lightweight panels always to be used for secondary or non-load bearing members. This paper presents an experimental study on properties (compressive strength, splitting tensile strength, water absorption) of lightweight foamed concrete (LFC) at two different curing methods. LFC with densities of 1500, 1700, and 1800 kg/m3, cement-sand ratio of 2:1 and water-cement ratio of 0.5 were investigated. The results showed LFC can be produced with the properties ofdensity range of 1500 to 1800 kg/m3 and corresponding compressive strength of 10 to 39 MPa. The higher the density of LFC, the less the water absorption for all the curing method considered, the highest and the lowest water absorption was 11.3% and 2.0% for 1500 kg/m3 cured in water and 1800 kg/m3 cured in air respectively. Compressive strength of LFC increases with age and density while water cured LFC has high compressive strength. Splitting tensile strength increases with density of LFC, but air cured LFC has more splitting tensile strength than water cured of the same density. The highest splitting tensile strength recorded was 3.92 MPa for 1800 kg/m3 cured in air, which was about 16% of its compressive strength at 28 days of curing age. These properties are important and can be applied to LFC precast structural members with air or water curing method which have less references for LFC in structural usage.  

scholarly journals Artificial Neural Network Estimation of the Effect of Varying Curing Conditions and Cement Type on Hardened Concrete Properties

Buildings ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 10 ◽  
Author(s):  
Gökhan Kaplan ◽  
Hasbi Yaprak ◽  
Selçuk Memiş ◽  
Abdoslam Alnkaa
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Hardened Concrete ◽  
Slag Cement ◽  
Curing Conditions ◽  
Concrete Properties ◽  
Concrete Production ◽  
Artificial Neural

The use of mineral admixtures and industrial waste as a replacement for Portland cement is recognized widely for its energy efficiency along with reduced CO2 emissions. The use of materials such as fly ash, blast-furnace slag or limestone powder in concrete production makes this process a sustainable one. This study explored a number of hardened concrete properties, such as compressive strength, ultrasonic pulse velocity, dynamic elasticity modulus, water absorption and depth of penetration under varying curing conditions having produced concrete samples using Portland cement (PC), slag cement (SC) and limestone cement (LC). The samples were produced at 0.63 and 0.70 w/c (water/cement) ratios. Hardened concrete samples were then cured under three conditions, namely standard (W), open air (A) and sealed plastic bag (B). Although it was found that the early-age strength of slag cement was lower, it was improved significantly on 90th day. In terms of the effect of curing conditions on compressive strength, cure W offered the highest compressive strength, as expected, while cure A offered slightly lower compressive strength levels. An increase in the w/c ratio was found to have a negative impact on pozzolanic reactions, which resulted in poor hardened concrete properties. Furthermore, carbonation effect was found to have positive effects on some of the concrete properties, and it was observed to have improved the depth of water penetration. Moreover, it was possible to estimate the compressive strength with high precision using artificial neural networks (ANN). The values of the slopes of the regression lines for training, validating and testing datasets were 0.9881, 0.9885 and 0.9776, respectively. This indicates the high accuracy of the developed model as well as a good correlation between the predicted compressive strength values and the experimental (measured) ones.

Wood-based support material for extrusion-based digital construction

2019 ◽  
Vol 25 (4) ◽  
pp. 690-698
Author(s):  
Julia Kaufhold ◽  
Johannes Kohl ◽  
Venkatesh Naidu Nerella ◽  
Christof Schroefl ◽  
Christoph Wenderdel ◽  
...  
Keyword(s):  
Compressive Strength ◽  
3D Printing ◽  
Construction Materials ◽  
Wood Particle ◽  
Support Material ◽  
General Applicability ◽  
Content Type ◽  
Wood Floor ◽  
Process Chains ◽  
Promising Solution

Purpose Extrusion-based digital construction (DC) approaches make it feasible to overcome constraints of conventional construction, namely, high formwork costs, long total construction times, low productivity and geometrical inflexibility. However, to date, no satisfactory solutions for extruding strongly inclined and horizontal elements are available. A wood-starch-composite has been systematically developed as a sustainable support material (SM) for extrusion-based DC. Design/methodology/approach Material and process-specific requirements were identified for this purpose, and a feasible process chain was developed. A parametric study was conducted to determine the influence of SM composition on its extrusion feasibility and compressive strength. Various compositions with two starch types and two wood particle shapes were tested. New, specific testing methods were developed. Selected compositions were tested using a 3D-printing device to verify extrudability and form stability. Findings Relationships between material compositions of SM and its rheological and mechanical properties were identified. All mixtures showed sufficient compressive strength in respect of the loading conditions analysed. However, their flow properties varied significantly. A mixture of native maize starch and wood floor was identified as the best variant (compressive strength 2.3 MPa). Research limitations/implications Comprehensive investigations of possible process chains, as well as full-scale demonstration and optimisation of the process parameters, were not in the scope of this paper. Such investigations are intended in further studies. Practical implications The general applicability of wood-based SM for DC with cement-based construction materials was proved. Originality/value The findings offer a novel and promising solution for 3D-printing of non-vertical concrete elements. Experimental setup and material compositions are detailed to ensure reproducibility.

scholarly journals Petrographic and Mechanical Characteristics of Concrete Produced by Different Type of Recycled Materials

Geosciences ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 264 ◽  
Author(s):  
Petros Petrounias ◽  
Panagiota P. Giannakopoulou ◽  
Aikaterini Rogkala ◽  
Paraskevi Lampropoulou ◽  
Basilios Tsikouras ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Mechanical Characteristics ◽  
Strength Class ◽  
Concrete Strength ◽  
Glass Waste ◽  
Recycled Materials ◽  
Curing Conditions ◽  
Different Types ◽  
Green Glass ◽  
Water Saturated

This paper examined three different types of recycled materials, such as beer green glass, waste tile, and asphalt, which will be used in different mixtures in order to prepare concrete specimens and, more specifically, their effect on concrete strength and how the petrographic characteristics of various recycled materials influenced the durability of C25/30 strength class concrete. Particular emphasis was placed on the effect of artificial microroughness of glassy and smooth surfaces of recycled materials on their final concrete strength. The concrete strength values do not show great variance, but their limited differences have been qualitatively interpreted by a new promising petrographic methodology, including the study of the surface texture of the used aggregate materials. Concretes are produced with constant volume proportions, workability, mixing, and curing conditions while using different sizes of each aggregate type. The aggregates were mixed both in dry and water saturated states in concretes. Concretes that are made by a mixture of beer green glass with quartz primer, as well as of tile with quartz primer, presented the optimum possible results of the compressive strength.

Enhancing mortar strengths by ternary geopolymer binder of metakaolin, slag, and palm ash

2017 ◽  
Vol 35 (5) ◽  
pp. 438-455 ◽  
Author(s):  
Ali Mohamed Ali Aboshia ◽  
Riza Atiq Rahmat ◽  
Muhammad Fauzi Mohd Zain ◽  
Amiruddin Ismail
Keyword(s):  
Compressive Strength ◽  
Precast Concrete ◽  
Carbon Dioxide Emission ◽  
Sitting Time ◽  
Geopolymer Concrete ◽  
Low Carbon ◽  
Palm Oil Fuel Ash ◽  
Content Type ◽  
Normal Strength ◽  
Geopolymer Binder

Purpose The purpose of this paper is to develop an alternative new ternary geopolymer mortar (MKSP) to resolve a traditional mortar problem which exhibits several disadvantages, including poor strengths and surface microcracks and the CO2 air pollution. Design/methodology/approach The MKSP ternary binder was produced using metakaolin (MK), slag (S), and palm oil fuel ash (POFA) activated with an alkaline mixture of sodium silicate (Na2SiO3) and 10 M NaOH in a mass ratio of 2.5. Seven different mix proportions of MK, slag, and POFA were used to fabricate MKSP mortars. The water-to-binder ratio was varied between 0.4 and 0.5. The mortars were heat cured for 2 h at 80°C and then aged in air. Flexural stress and strain, mortars flow and compressive strength were tested. Furthermore, the mortars were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) analyses. Findings The results showed that the sample MKSP6, which contained 40 percent MK, 40 percent slag, and 20 percent POFA, exhibited high compressive strength (52 MPa) without any cracks and flexural strength (6.9 MPa) at 28 days after being cured for 2 h at 80°C; however, the MKSP7 mortar with optimal strength of 55 MPa showed some surface cracks . Further, the results of the XRD, SEM, and FTIR analyses indicated that the MKSP mortars primarily consisted of a crystalline (Si+Al) phase (70 percent) and a smaller amorphous (Si+Ca) phase (30 percent). Research limitations/implications The MKSP ternary geopolymer mix has three limitations as an importance of heat curing for development early strength, POFA content less than 20 percent to gain high normal strength and delaying the sitting time by controlling the slag content or the alkali activator type. Practical implications The use of geopolymer materials binder in a real building is limited and it still under research, Thus, the first model of real applied geopolymer cement in 2008 was the E-Crete model that formed by Zeobond company Australia to take the technology of geopolymer concrete to reality. Zeobond Pty Ltd was founded by Professor Jannie S.J. van (van Deventer et al., 2013), it was used to product precast concrete for the building structure. The second model was PYRAMENT model in 2002 by American cement manufacturer Lone Star Industries which was produced from the development carried out on inorganic alumino-silicate polymers called geopolymer (Palomo et al., 1999). In 2013 the third model was Queensland’s University GCI building with three suspended floors made from structural geopolymer concrete containing slag/fly ash-based geopolymer (Pathak, 2016). In Australia, 2014, the newly completed Brisbane West Wellcamp airport becomes the greenest airport in the world. Cement-free geopolymer concrete was used to save more than 6,600 tons of carbon emissions in the construction of the airport. Therefore, the next century will see cement companies developing alternative binders that are more environmentally friendly from a sustainable development point of view. Originality/value Production of new geopolymer binder of mortar as alternative to traditional cement binder with high early and normal strength from low cost waste materials, less potential of cracking, less energy consumption need and low carbon dioxide emission.

scholarly journals Enhancement of Energy Absorption Capacity of Polyethylene Fiber-Reinforced Cementitious Composites According to Admixtures and Curing Conditions

2020 ◽  
Vol 20 (1) ◽  
pp. 319-325
Author(s):  
Min-Jae Kim ◽  
Hong-Joon Choi ◽  
Booki Chun ◽  
Wonsik Shin ◽  
Doo-Yeol Yoo
Keyword(s):  
Compressive Strength ◽  
Tensile Test ◽  
Energy Absorption ◽  
Absorption Capacity ◽  
Limestone Powder ◽  
Cementitious Composites ◽  
Energy Absorption Capacity ◽  
Curing Conditions ◽  
Direct Tensile ◽  
Direct Tensile Test

This study aims to enhance the energy absorption capacity of cementitious composites with 2 vol.% of polyethylene fibers, by adjusting mixing ingredients and curing conditions. Ground blast furnace slag, cement kiln dust, limestone powder, and silica fume were incorporated, and two different curing conditions were applied: 72 h of curing at 90 ℃ and 120 h of curing at 40 ℃. Compressive strength test and direct tensile test were performed on 6 mixtures and the test results were compared with those of ultra-high-performance concrete and engineered cementitious composite specimens. The maximum compressive strength of the 6 mixtures was measured to be approximately 117 MPa. The higher cement replacement ratio of the other components resulted in a decrease in the compressive strength of the specimens cured at 90 ℃. In the direct tensile test, the specimens cured at 40 ℃ exhibited lower tensile strength than those cured at 90 ℃, but the strain capacity was increased by approximately 305% and reached 7.7%. This also resulted in an enhancement of the energy absorption capacity from 80%–292% because of the differences in micro-cracking and fracturing behaviors, such as an increase inthe number of micro-cracks and decrease in crack width.

scholarly journals The use of non-destructive tests to estimate Self-compacting concrete compressive strength

2018 ◽  
Vol 149 ◽  
pp. 01036
Author(s):  
Boukhelkhal Djamila ◽  
Guendouz Mohamed
Keyword(s):  
Compressive Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Mineral Admixture ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Self Compacting Concrete ◽  
Correlation Relationship ◽  
Granulated Slag

Until now, there are few studies on the effect of mineral admixtures on correlation between compressive strength and ultrasonic pulse velocity for concrete. The aim of this work is to study the effect of mineral admixture available in Algeria such as limestone powder, granulated slag and natural pozzolana on the correlation between compressive strength and corresponding ultrasonic pulse velocity for self-compacting concrete (SCC). Compressive strength and ultrasonic pulse velocity (UPV) were determined for four different SCC (with and without mineral admixture) at the 3, 7, 28 and 90 day curing period. The results of this study showed that it is possible to develop a good correlation relationship between the compressive strength and the corresponding ultrasonic pulse velocity for all SCC studied in this research and all the relationships had exponential form. However, constants were different for each mineral admixture type; where, the best correlation was found in the case of SCC with granulated slag (R2 = 0.85). Unlike the SCC with pozzolana, which have the lowest correlation coefficient (R2 = 0.69).

scholarly journals Effect of Curing Conditions on the Compressive Strength of Self Compacting Concrete Incorporating Slag and Steel Fibres

2019 ◽  
Vol 8 (4) ◽  
pp. 4754-4760
Keyword(s):  
Compressive Strength ◽  
Treatment Period ◽  
Water Immersion ◽  
Site Conditions ◽  
Self Compacting Concrete ◽  
Steam Curing ◽  
Curing Conditions ◽  
Manufactured Sand ◽  
Curing Methods ◽  
Curing Cycle

The influence of different curing conditions on the compressive strength of Self compacting concrete in combination of Slag and Manufactured sand (MSand) is only little known, especially when subjected to steam accelerated curing process.Water immersion curing, Sealed curing, Curing compounds, Air Curing, Curing at site conditions and curing with steam were considered for the present study on the compressive strength of Self compacting concrete (SCC).The specimens were tested for 3,7,28&90 days. Out of the various curing methods, the highest compressive strength achieved is for Water immersion curing followed by Sealed curing (95%), curing compounds (93%), curing at site conditions (89%) and air curing (75%).Curing using steam was introduced to optimize the steam curing cycle for SCC. 36 different steam curing cycles were considered with varying temperatures of 50, 60 and 700C.The treatment period considered for the study were 8, 10, 12 &14 hours. From the experimental investigation, it is observed that increase in temperature and total cycle time led to higher immediate compressive strength. Out of the 36 curing cycles, the optimum cycle is having a temperature of 600 c, delay period of 5 hours and a treatment period of 12 hrs

Sign in / Sign up

Export Citation Format

Share Document