scholarly journals Enhancement of Energy Absorption Capacity of Polyethylene Fiber-Reinforced Cementitious Composites According to Admixtures and Curing Conditions

2020 ◽  
Vol 20 (1) ◽  
pp. 319-325
Author(s):  
Min-Jae Kim ◽  
Hong-Joon Choi ◽  
Booki Chun ◽  
Wonsik Shin ◽  
Doo-Yeol Yoo
Keyword(s):  
Compressive Strength ◽  
Tensile Test ◽  
Energy Absorption ◽  
Absorption Capacity ◽  
Limestone Powder ◽  
Cementitious Composites ◽  
Energy Absorption Capacity ◽  
Curing Conditions ◽  
Direct Tensile ◽  
Direct Tensile Test

This study aims to enhance the energy absorption capacity of cementitious composites with 2 vol.% of polyethylene fibers, by adjusting mixing ingredients and curing conditions. Ground blast furnace slag, cement kiln dust, limestone powder, and silica fume were incorporated, and two different curing conditions were applied: 72 h of curing at 90 ℃ and 120 h of curing at 40 ℃. Compressive strength test and direct tensile test were performed on 6 mixtures and the test results were compared with those of ultra-high-performance concrete and engineered cementitious composite specimens. The maximum compressive strength of the 6 mixtures was measured to be approximately 117 MPa. The higher cement replacement ratio of the other components resulted in a decrease in the compressive strength of the specimens cured at 90 ℃. In the direct tensile test, the specimens cured at 40 ℃ exhibited lower tensile strength than those cured at 90 ℃, but the strain capacity was increased by approximately 305% and reached 7.7%. This also resulted in an enhancement of the energy absorption capacity from 80%–292% because of the differences in micro-cracking and fracturing behaviors, such as an increase inthe number of micro-cracks and decrease in crack width.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

Compressive Properties of Electroless Ni-P Coating Reinforced Magnesium Alloy Foams

2021 ◽  
Vol 889 ◽  
pp. 123-128
Author(s):  
Sheng Jun Liu ◽  
Zhi Qiang Dong ◽  
Ren Zhong Cao ◽  
Da Song ◽  
Jia An Liu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Energy Absorption ◽  
Absorption Efficiency ◽  
Absorption Capacity ◽  
Compressive Properties ◽  
Compressive Test ◽  
Energy Absorption Capacity ◽  
Energy Absorption Efficiency ◽  
Hybrid Foams ◽  
Electroless Ni

In this study, the open-cell Mg-2Zn-0.4Y foams were prepared by infiltration casting method. The Ni/Mg hybrid foams were prepared by electroless Ni-P coating on the foam struts to improve the compressive strength and energy absorption capacity. The compressive properties of the Mg alloy foams and Ni/Mg hybrid foams were studied by quasi-static compressive test. The experimental results show that the Ni-P coating is composed of crystallites. The Ni-P coating can significantly enhance the compressive strength, energy absorption capacity and energy absorption efficiency of the foams.

scholarly journals Tensile Behavior Characteristics of High-Performance Slurry-Infiltrated Fiber-Reinforced Cementitious Composite with Respect to Fiber Volume Fraction

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3335 ◽  
Author(s):  
Seungwon Kim ◽  
Dong Joo Kim ◽  
Sung-Wook Kim ◽  
Cheolwoo Park
Keyword(s):  
Tensile Strength ◽  
Energy Absorption ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Absorption Capacity ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Energy Absorption Capacity ◽  
Direct Tensile ◽  
Direct Tensile Strength

Concrete has high compressive strength, but low tensile strength, bending strength, toughness, low resistance to cracking, and brittle fracture characteristics. To overcome these problems, fiber-reinforced concrete, in which the strength of concrete is improved by inserting fibers, is being used. Recently, high-performance fiber-reinforced cementitious composites (HPFRCCs) have been extensively researched. The disadvantages of conventional concrete such as low tensile stress, strain capacity, and energy absorption capacity, have been overcome using HPFRCCs, but they have a weakness in that the fiber reinforcement has only 2% fiber volume fraction. In this study, slurry infiltrated fiber reinforced cementitious composites (SIFRCCs), which can maximize the fiber volume fraction (up to 8%), was developed, and an experimental study on the tensile behavior of SIFRCCs with varying fiber volume fractions (4%, 5%, and 6%) was carried out through direct tensile tests. The results showed that the specimen with high fiber volume fraction exhibited high direct tensile strength and improved brittleness. As per the results, the direct tensile strength is approximately 15.5 MPa, and the energy absorption capacity was excellent. Furthermore, the bridging effect of steel fibers induced strain hardening behavior and multiple cracks, which increased the direct tensile strength and energy absorption capacity.

Properties of steel fiber self-compacting concrete incorporating quarry dust fine powder

2020 ◽  
Vol 11 (1) ◽  
pp. 1
Author(s):  
Joseph Abah Apeh ◽  
Juliet Eyum Ameh
Keyword(s):  
Compressive Strength ◽  
Energy Absorption ◽  
Steel Fiber ◽  
Fine Powder ◽  
Absorption Capacity ◽  
Strength Development ◽  
Self Compacting Concrete ◽  
Energy Absorption Capacity ◽  
Hardened Properties ◽  
Quarry Dust

Self-compacting concrete (SCC) has great potentials as it offers several environmental, economic and technical benefits. Moreover, the use of fibers extends its possibilities since fibers arrest cracks and retard their propagation. Incorporation of Quarry Dust (QD) in SCC help to reduce environmental hazards during the production of QD. This study evaluated the fresh and hardened properties of steel fiber self-compacting concrete (SFSCC) incorporating QD. The optimum fiber and QD contents with no adverse effects on fresh and hardened properties were determined. A comparative study on behavior of SCC and SFSCC mixtures in terms of workability, compressive strength, compressive strength development ratio, tensile, flexural and energy absorption capacity was carried out. Test results showed that compressive strength increased with increase in QD contents at fixed fiber content by mass of Portland cement (PC) and then decreased. Strength development ratio (C28/C7) for SCC was 1.13, while it was 1.06, 1.08, 1.10 and 1.01 after reinforcing with 0.10, 0.20 and 0.30 contents of fiber. The compressive, tensile, flexural and energy absorption capacity or Toughness of SFSCC increased with the inclusion of the aforementioned contents of steel fiber up to 0.20 % volume of total binder at constant QD content and then decreased when compared with control SCC values. From these results, optimum value for the variables studied was obtained from mix QD20 + 0.2fr. Hence, steel fiber and QD could be successfully used in SCC production not minding the slight draw back on workability of SCC caused by inclusion of steel fiber, but with a modified dosage of super-plasticizer (SP), fresh and hardened properties, in accordance with specifications in relevant code(s) can be achieved.

Experimental investigation of recycled aggregate effect on the concrete properties

2018 ◽  
Vol 9 (4) ◽  
pp. 560-571
Author(s):  
Hamed Hemmati Pourghashti ◽  
Malek Mohammad Ranjbar ◽  
Rahmat Madandoust
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Tensile Test ◽  
Recycled Concrete ◽  
Test Results ◽  
Content Type ◽  
Treatment Conditions ◽  
Natural Aggregates ◽  
Direct Tensile ◽  
Direct Tensile Test

Purpose The purpose of this paper is to conduct a laboratory investigation on measuring the tensile strength of recycled concrete using a double punch test. Furthermore, one of the main goals of this study is to compare the tensile and compressive strengths of recycled concrete samples. Design/methodology/approach Recycled concrete samples were made with variables such as aggregate type (natural stone and aggregate recycled concrete), different water-to-cement ratios and different treatment conditions in the first stage. In the next stage, the double punch test was performed on them, and finally the results obtained from experiments were analyzed and investigated. Findings According to the above tests, it was concluded that: first, according to the laboratory results, the strength of concrete containing recycled aggregates becomes closer to the strength of concrete containing natural aggregates whenever the water-to-cement ratio is higher. Second, upon investigating the treatment conditions, it was observed that the treatment had a greater effect on the strength of the recycled concrete. However, this effect was less tangible in tensile strength. Third, upon investigating the results of tensile strength, it can be said that the Barcelona test results were closer to the direct tensile test results compared to the Brazilian test results. This indicates the higher viability of Barcelona’s test results. Fourth, the results obtained from the Barcelona tensile test for recycled concrete were closer to the results of the direct tensile test compared to the concrete containing natural aggregates, which suggests that the Barcelona test is more suitable as a tensile test for recycled concrete. Fifth, the effects of various factors on tensile strength were somewhat less compared to the compressive strength, although very close. Sixth, the relationships provided by the regulation for concrete tensile strength on compressive strength were highly inconsistent with the results obtained from the direct tensile test, for which the consistency was higher for concrete containing natural aggregates compared to recycled concrete. Seventh, the dispersion of results obtained from tensile tests was higher for recycled concrete compared to concrete containing natural aggregates, but lesser of this dispersion was observed in the compressive strength. Originality/value According to the laboratory results, the strength of concrete containing recycled aggregates becomes closer to the strength of concrete containing natural aggregates whenever the water-to-cement ratio is higher. Upon investigating the treatment conditions, it was observed that the treatment had a greater effect on the strength of the recycled concrete. However, this effect was less tangible in tensile strength. On the basis on the results of the tensile strength, it can be said that the Barcelona test results were closer to the results of the direct tensile test compared to those of the Brazilian test. This indicates the higher viability of Barcelona’s test results. The results obtained from the Barcelona tensile test for recycled concrete were closer to the results of direct tensile test compared to the concrete containing natural aggregates, which suggests that the Barcelona test is more suitable as a tensile test for recycled concrete. The effects of various factors on tensile strength were somewhat less compared to the compressive strength, although very close. The relationships provided by the regulation for concrete tensile strength on compressive strength were highly inconsistent with the results obtained from the direct tensile test, for which the consistency was higher for concrete containing natural aggregate compared to recycled concrete. The dispersion of results obtained from tensile tests was higher for recycled concrete compared to concrete containing natural aggregate, but lesser of this dispersion was observed in the compressive strength.

The compressive properties and strengthening mechanism of the middle-trabecular beetle elytron plate

2018 ◽  
Vol 22 (4) ◽  
pp. 948-961 ◽  
Author(s):  
Jinxiang Chen ◽  
Xindi Yu ◽  
Mengye Xu ◽  
Yoji Okabe ◽  
Xiaoming Zhang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Energy Absorption ◽  
Sandwich Structures ◽  
Strengthening Mechanism ◽  
Absorption Capacity ◽  
Compressive Properties ◽  
Energy Absorption Capacity ◽  
Standard Energy

For the development of new types of lightweight sandwich structures, the compressive properties and strengthening mechanism of the middle-trabecular beetle elytron plate were investigated for various values of η (the ratio of the trabecular radius to the honeycomb wall length). The results are as follows: (1) When η = 0.1, the increases in the compressive strength and standard energy absorption capacity of the middle-trabecular beetle elytron plate compared with the honeycomb plate exceed those of the end-trabecular beetle elytron plate; with an increase to η = 0.15, the compressive strength remains nearly the same, the energy absorption capacity undergoes a significant further increase, and the trabeculae exhibit Φ-type failure. (2) The strengthening mechanism that gives rise to the compressive properties of the middle-trabecular beetle elytron plate is proposed as follows: the trabeculae are located at the center of the honeycomb walls, where the maximum deformations would otherwise occur; they constrain the deformation of the honeycomb walls; and the number of trabeculae in the middle-trabecular beetle elytron plate also exceeds that in the end-trabecular beetle elytron plate. (3) Middle-trabecular beetle elytron plates have the advantage of facile manufacturing, which will establish a basis for promoting the application of beetle elytron plates.

Influence of Hybrid Steel Fiber Addition on Direct Tensile Behavior of UHPC

2016 ◽  
Vol 713 ◽  
pp. 270-272
Author(s):  
Seung Hun Park ◽  
Kyung Taek Koh ◽  
Gum Sung Ryu ◽  
Gi Hong An ◽  
Nam Kon Lee
Keyword(s):  
High Performance ◽  
Steel Fiber ◽  
Absorption Capacity ◽  
Tensile Behavior ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Energy Absorption Capacity ◽  
High Performance Fiber ◽  
Direct Tensile ◽  
Direct Tensile Test

This paper examines the direct tensile behavior of ultra high performance fiber reinforced concrete (UHPFRC) according to the addition of hybrid-type steel fibers with different lengths and diameters but identical aspect ratio. Two types of steel fibers that are MS fiber with length of 20 mm and diameter of 0.2 mm and LS fiber with length of 22 mm and diameter of 0.22 mm are adopted and admixed together with different proportions to give three series of mixes (MS10LS05, MS075LS075, MS05LS10). Direct tensile test is conducted on specimens using each of the considered mixes and notched on both sides. The results show that the tensile strength and the energy absorption capacity of UHPFRC tend to increase with larger proportions of relatively long steel fibers.

scholarly journals Impact Energy Consumption of High-Volume Rubber Concrete with Silica Fume

2019 ◽  
Vol 2019 ◽  
pp. 1-11
Author(s):  
Hai-long Li ◽  
Ying Xu ◽  
Pei-yuan Chen ◽  
Jin-jin Ge ◽  
Fan Wu
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Energy Absorption ◽  
Silica Fume ◽  
Impact Energy ◽  
Impact Resistance ◽  
Absorption Capacity ◽  
Rubberized Concrete ◽  
Energy Absorption Capacity ◽  
Fine Aggregates

Adding rubber to concrete aims to solve the environmental pollution problem caused by waste rubber and to improve the energy absorption and impact resistance of concrete. In this paper, recycled rubber particles were used to replace fine aggregates in Portland cement concrete to combine the elasticity of rubber with the compression resistance of concrete. Fine aggregates in the concrete mixes were partially replaced with 0%, 20%, 40%, and 60% rubber by volume, and the cement in the concrete mixes was replaced with 0%, 5%, and 10% of silica fume by mass. The properties of the concrete specimens were examined through compressive strength, splitting tensile strength, flexural loading, and rebound tests. Results show that the compressive strength of concrete and the splitting tensile strength decreased to 11.81 and 1.31 MPa after adding silica fume to enhance the strength 37.8% and 23.7%, respectively, and the dosage of rubber was 60%. With the addition of rubber, the impact energy of rubberized concrete was 2.39 times higher than that of ordinary concrete, while its energy absorption capacity was 9.46% higher. The addition of silica fume increased its impact energy by 3.06 times, but the energy absorption capacity did not change significantly. In summary, the RC60SF10 can be used on non-load-bearing structures with high impact resistance requirements. A scanning electron microscope was used to examine and analyze the microstructural properties of rubberized concrete.

High-Performance Impact-Resistant Concrete Mixture for Transportation Infrastructure Applications

2019 ◽  
Vol 2673 (12) ◽  
pp. 628-635 ◽  
Author(s):  
Kamal Baral ◽  
Jovan Tatar ◽  
Qian Zhang
Keyword(s):  
Energy Absorption ◽  
High Performance ◽  
Impact Resistance ◽  
Absorption Capacity ◽  
Flexural Behavior ◽  
Cementitious Composites ◽  
Repeated Impact ◽  
Energy Absorption Capacity ◽  
Transportation Infrastructures ◽  
The Impact

Engineered cementitious composites (ECC) is a class of high-performance fiber-reinforced cementitious composites featuring metal-like strain-hardening behavior under tension and high ductility. The highly ductile behavior of ECC often results in high impact resistance and energy absorption capacity, which make ECC suitable for applications in structures that are prone to impact damages, like exterior bridge girders, bridge piers, and crash barriers. In a recent study, a new ECC mixture has been developed using domestically available polyvinyl alcohol (PVA) fibers and regular river sand in replacement of imported PVA fibers and fine silica sand that are normally used in other ECC mixtures. The newly developed mixture, with improved local accessibility of raw materials, enables structural-scale applications of ECC in transportation infrastructures. To evaluate the suitability of the mixture for impact-resistant structures, in this paper, the tensile and flexural behavior of the newly developed material were characterized under pseudo-static loading and high strain-rate loadings up to 10−1 s−1. Direct drop-weight impact test was also conducted to assess the impact resistance and energy absorption capacity of the material. It was ensured that the ECC mixture maintains high tensile strain capacity above 1.8% under all tested strain rates. Regarding the damage characteristics, energy absorption capacity and load-bearing capacity during repeated impact loadings, ECC was found to have 75% higher energy dissipation capacity compared with regular reinforced concrete specimens and superior damage tolerance. The research results demonstrated that the newly developed ECC has a great potential to improve the impact resistance of transportation infrastructures.

Sign in / Sign up

Export Citation Format

Share Document