Study of the influence of lubrication parameters on gear lubrication properties and efficiency

2016 ◽  
Vol 68 (6) ◽  
pp. 647-657 ◽  
Author(s):  
Kaiyue Li ◽  
Guoding Chen ◽  
Deng Liu
Keyword(s):  
Power Consumption ◽  
Film Thickness ◽  
High Speed ◽  
Hydrodynamic Lubrication ◽  
Quantitative Relationship ◽  
Gear Transmission ◽  
Content Type ◽  
Oil Film ◽  
Friction Power ◽  
Lubricating Properties

Purpose The analysis of lubricating properties and efficiency is important for aviation high-speed gear. So far, the project of lubricating properties and efficiency are processing under the condition of a given lubricating state, which is still depending on practical experience. This paper aims to mostly focus on the analysis of given lubricating state but lost sight of the relevance of lubrication parameters and lubricating state, which not only makes the analysis of aviation high-speed gear transmission and efficiency fail to trace to practical situation but also has an adverse effect on the reliance and validity of the project. Design/methodology/approach Based on this, the numerical model of spraying oil and oil film spreading is established, and the quantitative relationship between spray lubrication parameters and spreading characteristics of oil film is studied. According to the geometric and mechanical conditions of meshing points and taking the influence of rich-oil/starved-oil lubrication and roughness of teeth surface into consideration, corrected film thickness under condition of elasto-hydrodynamic lubrication and lubricating state of mesh points are analyzed. On this basis, power consumption and efficiency of gear transmission are also calculated by figuring out the solid friction and oil friction separately. Findings Through the research of this thesis, the effect of friction power consumption and efficiency with lubrication parameters is discussed. The effect of lubrication parameters on friction power consumption and efficiency of gear is complex. With the increase of spreading film thickness and film length, the frictional power consumption is less and the efficiency is higher. Originality/value This work provides a systematic technological approach to lubrication design and efficiency calculation of aviation high-speed gear transmission, which has remarkable engineering significance for the accurate lubrication design of the aviation mechanical parts.

Elastohydrodynamic Lubrication Design of Planetary Gear Transmission

2011 ◽  
Vol 228-229 ◽  
pp. 681-685
Author(s):  
Pei De Bao ◽  
Jun Xie ◽  
Xiao Qin Yin ◽  
Qi Zhi Yang ◽  
Lu Zhong Ma
Keyword(s):  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Elastohydrodynamic Lubrication ◽  
Planetary Gear ◽  
Gear Transmission ◽  
The Sun ◽  
Oil Film ◽  
Lubrication Film ◽  
Planet Gear ◽  
The Many

Based on elastic hydrodynamic lubrication (EHL) theory, an EHL model of the meshing between the sun gear and planet gear in planetary gear transmission was established. The EHL oil film thicknesses at meshing areas and those distributions for two operation cases were calculated: one case with the sun gear as the driving gear and another case with the ring gear as the driving gear. The Lubrication with second case was worse. Through the many comparing calculations the lubrication film thickness can be significantly increased by right parameter design. Reasonable raise of lubricant viscosity can get better gear lubrication. Increased gear pressure angle can greatly increase the oil film thickness. The increase of oil film thickness can improve the lubrication of gears and prevent wearing and reduce the production cost of gears, which have great practical value.

The effect of lubricant viscosity model with improver on friction and lubrication of piston skirt-cylinder liner conjunction

2019 ◽  
Vol 72 (1) ◽  
pp. 157-164
Author(s):  
Gu Xin ◽  
Xiao-Ri Liu ◽  
Dong-Kang Cheng ◽  
Qing-Ping Zheng ◽  
Meng-Han Li ◽  
...  
Keyword(s):  
Shear Rate ◽  
Film Thickness ◽  
Friction Force ◽  
Cylinder Liner ◽  
Content Type ◽  
Oil Film ◽  
Friction Power ◽  
Piston Skirt ◽  
Lubricant Viscosity ◽  
Oil Film Pressure

Purpose This paper aims to investigate the effect of lubricant viscosity model with improver on friction and lubrication of piston skirt-cylinder liner conjunction. Design/methodology/approach A dynamic calculation model is established for the piston skirt-cylinder liner conjunction of a heavy-duty commercial diesel engine, to explore the effects of two kinds of lube oil viscosity models named after polyalkyle-metacrylate-1 (PAMA1) and styrene-isoprene-copolymer (SICP) improvers on the maximum oil film viscosity, the minimum oil film thickness, the peak oil film pressure, the maximum shear rate, the friction force and the total friction power loss. Findings The variation trends with the crank angle of the above parameters are not changed with the difference of improvers, while obvious numerical differences are found except the maximum oil film pressure. The minimum oil film thickness and maximum shear rate of PAMA1 are larger than that of SICP, the maximum oil film viscosity of SICP is larger than that of PAMA1, which indicates that the shear-thinning effect of PAMA1 is greater, the maximum friction force on the piston of SICP is larger than that of PAMA1, and the total friction power consumption is also larger, the average friction power consumptions of SICP and PAMA1 are 385.4 and 262.8 W, respectively, with the relative difference of 31.8 per cent. Originality/value The influence of different lubricating oil additive models on the lubrication and friction of piston skirt-cylinder liner conjunction is simulated and analyzed.

Skidding research of a high-speed cylindrical roller bearing with beveled cage pockets

2020 ◽  
Vol 72 (7) ◽  
pp. 969-976
Author(s):  
Yanbin Liu ◽  
Zhanli Zhang
Keyword(s):  
Peer Review ◽  
Tilt Angle ◽  
High Speed ◽  
Hydrodynamic Lubrication ◽  
Roller Bearing ◽  
Front Wall ◽  
Dynamics Model ◽  
Content Type ◽  
Cylindrical Roller Bearing ◽  
Cylindrical Roller

Purpose This study aims to uncover the influencing mechanism of the tilt angles of the cage pocket walls of the high-speed cylindrical roller bearing on the bearing skidding. Design/methodology/approach A novel cylindrical roller bearing with the beveled cage pockets was proposed. Using the Hertz contact theory and the elastohydrodynamic and hydrodynamic lubrication formulas, the contact models of the bearing were built. Using the multibody kinematics and the Newton–Euler dynamics theory, a dynamics model of the bearing was established. Using the Runge–Kutta integration method, the dynamics simulations and analysis of the bearing were performed. Findings The simulation results show that the effects of the tilt angles of the front and rear walls of the pocket on the bearing skidding are remarkable. Under a 5° tilt angle of the front wall of the pocket and a 10° tilt angle of the rear wall, the bearing skidding can be effectively decreased in the rotational speed range of 10,000-70,000 r/min. Originality/value In this paper, a novel cylindrical roller bearing with the beveled cage pockets was proposed; a dynamics model of the bearing was established; the influence mechanism of the tilt angles of the front and rear walls of the pocket on the bearing skidding was investigated, which can provide fundamental theory basis for optimizing the pocket. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2020-0035/

Dynamic transmission of oil film in soft-start process of HVD considering surface roughness

2018 ◽  
Vol 70 (3) ◽  
pp. 463-473 ◽  
Author(s):  
Fangwei Xie ◽  
Jie Zhu ◽  
Jianzhong Cui ◽  
Xudong Zheng ◽  
Xinjian Guo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Friction Pair ◽  
Maximum Temperature ◽  
Force Model ◽  
Content Type ◽  
Oil Film ◽  
Soft Start ◽  
Viscous Torque ◽  
Start Process

Purpose The purpose of this paper is to study the dynamic transmission of the oil film in soft start process of hydro-viscous drive (HVD) between the friction pairs with consideration of surface roughness, and obtain the distribution law of temperature, velocity, pressure, shear stress and viscous torque of the oil film. Design/methodology/approach The revised soft-start models of HVD were derived and calculated, including average Reynolds equation, asperity contact model, load force model and total torque model. Meanwhile, a 2D model of the oil film between friction pair was built and solved numerically using computational fluid dynamics (CFD) technique in FLUENT. Findings The results show that the maximum temperature gradually reduces from the intermediate range (z = 0.5 h) to the inner side of the friction pair along the direction of oil film thickness. As the soft-start process continues, pressure gradient along the direction of the oil film thickness gradually changes to zero. In addition, tangential velocity increases and yet radial velocity decreases with the increase of the radius. Originality/value In this paper, it was found that the viscous torque calculated by the numerical method is smaller than that by the CFD model, but their overall trend is almost the same. This also demonstrates the effectiveness of the numerical simulation.

Measurement and calculation of oil film thickness in a ball bearing

2018 ◽  
Vol 70 (8) ◽  
pp. 1500-1508 ◽  
Author(s):  
Baogang Wen ◽  
Hongjun Ren ◽  
Pengfei Dang ◽  
Xu Hao ◽  
Qingkai Han
Keyword(s):  
Film Thickness ◽  
Ball Bearing ◽  
Performance Indicator ◽  
Thickness Distribution ◽  
Content Type ◽  
Oil Film ◽  
Capacitance Method ◽  
Lubrication Condition ◽  
Series Of Experiments ◽  
External Loads

PurposeThe oil film thickness provides a key performance indicator of a ball bearing lubrication condition. This paper aims to propose an approach to calculate and measure the oil film thickness of the bearing.Design/methodology/approachOn a specially designed test rig, measurement of the capacitance is used to monitor the oil film thickness of ball bearing. A corrected film thickness formula taking account of the influences of non-Newtonian shear thinning and thermal is introduced to predict the oil film thickness of ball bearing. And then the film thickness distribution and the corresponding capacitances are calculated.FindingsMeasurement and calculation of oil film thickness in a ball bearing are carried out under various rotating speeds and external loads. By comparing the calculated capacitances with measured results, it can be concluded that the calculated results obtained by the amended film thickness formula are much closer to the test findings than the classical computed values according to Hamrock–Dowson.Originality/valueA new corrected film thickness formula is introduced in predicting oil film thickness of ball bearing and verified by the series of experiments according to capacitance method.

Experimental analysis of influence of double-layer bump foils on aerodynamic thrust foil bearings performance

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fangcheng Xu ◽  
Zeda Dong ◽  
Jianhua Chu ◽  
Haoming Wang ◽  
Yongliang Wang
Keyword(s):  
Power Consumption ◽  
Double Layer ◽  
External Force ◽  
Performance Optimization ◽  
Load Capacity ◽  
Foil Thickness ◽  
Selection Scheme ◽  
Content Type ◽  
Friction Power ◽  
Foil Bearings

Purpose Gas thrust foil bearings (GTFBs) are used to balance the axial load of engines. However, in some working conditions of large axial force, such as the use of single impeller air compressor, the load capacity of GTFBs is still insufficient. To solve this problem, the load capacity can be improved by increasing the stiffness of bump foil. The purpose of this paper is to explore a scheme to effectively improve the performance of thrust foil bearings. In the paper, the stiffness of bump foil is improved by increasing the thickness of bump foil and using double-layer bump foil. Design/methodology/approach The foil deformation of GTFBs supported by three different types of bump foils, the relationship between friction power consumption and external force and the difference of limited load capacity were measured by experimental method. Findings The variation of the foil deformation, bearing stiffness, friction power consumption with the external force at different speeds and limited load capacity are obtained. Based on experimental results, the selection scheme of bump foil thickness is obtained. Originality/value This paper provides a feasible method for the performance optimization of GTFBs.

Experimental study on line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuqin Yang ◽  
Dexing Hu ◽  
Qianhao Xiao ◽  
Shun Zhao
Keyword(s):  
Film Thickness ◽  
Surface Texture ◽  
Inhibitory Effect ◽  
Lubricating Oil ◽  
Line Contact ◽  
Grease Lubrication ◽  
Content Type ◽  
Oil Film ◽  
Crown Width ◽  
Lubrication Properties

Purpose This paper aims to study line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers as well as the effect of different crown widths (dw) on oil film thickness under textured conditions. Design/methodology/approach The laser processing method was used to make the micro-texture on the surface of GCr15 steel rollers; lithium grease was used as the lubricant, and line-contact elastohydrodynamic grease lubrication experiments under pure sliding conditions were performed on light interference elastohydrodynamic-lubricated experimental table. Findings The results show that the line-contact elastohydrodynamic grease lubrication is closely related to the textured crown width of steel rollers. At low speeds and light loads, texturing has an inevitable inhibitory effect on the formation of the lubricating oil film, and the smaller the width of the crown area, the more obvious the inhibitory effect, which is not conducive to the improvement of the lubrication condition. At high speeds and high loads, the textured roller with dw = 1 mm has the largest oil film thickness and shows better lubrication performance. Originality/value At present, there is little research on the surface texture of line-contact friction pairs. This work explores the effect of different textured crown width on the lubricating properties of line-contact elastohydrodynamic grease lubrication by experiment. It provides a new theoretical basis for the subsequent practical application of surface texture technology.

Size effect on thermal elastohydrodynamic lubrication of industrial chain bush-pin hinge pair

2019 ◽  
Vol 71 (9) ◽  
pp. 1080-1085 ◽  
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Yi Liu ◽  
Longjie Dai ◽  
Zhaohua Shang
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Curvature Radius ◽  
Line Contact ◽  
Content Type ◽  
Oil Film ◽  
Industrial Chain ◽  
Infinite Line

Purpose The purpose of this paper is to use elastohydrodynamic lubrication (EHL) theory to study the variation of the equivalent curvature radius “R” on the change of oil film thickness, pressure, temperature rise and friction coefficient in the contact zone between bush-pin in industrial chain drive. Design/methodology/approach In this paper, the contact between bush and pin is simplified as infinitely long line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. The two constitutive equations, namely, Newton fluid and Ree–Eyring fluid are used in the calculations. Findings It is found that with the increase of equivalent curvature radius, the thickness of oil film decreases and the temperature rise increases. Under the same condition, the friction coefficient of Newton fluid is higher than that of Ree–Eyring fluid. When the load increases, the oil film thickness decreases, the temperature rise increases and the friction coefficient decreases; and the film thickness increases with the increase of the entraining speed under the condition “R < 1,000 mm”. Research limitations/implications The infinite line contact assumption is only an approximation. For example, the distances between the two inner plates are 5.72 mm, by considering the two parts assembled into the inner plates, the total length of the bush is less than 6 mm. The diameter of the pin and the bore diameter of the bush are 3.28 and 3.33 mm. However, the infinite line contact is also helpful in understanding the general variation of oil film characteristics and provides a reference for the future study of finite line contact of chain problems. Originality/value The change of the equivalent radius R on the variation of the oil film in the contact of the bush and the pin in industrial chain drive was investigated. The size effect influences the lubrication characteristic greatly in the bush-pin pair.

A thermal EHL investigation for size effect of finite line contact on bush-pin hinge pairs in industrial chains

2020 ◽  
Vol 72 (5) ◽  
pp. 695-701
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Peiran Yang ◽  
Zhaohua Shang ◽  
Yi Liu ◽  
...  
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Contact Zone ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Oil Film ◽  
Finite Line Contact ◽  
Finite Line ◽  
Thermal Ehl

Purpose This paper aims to study the influence of the dimension change of bush-pin on the pressure, oil film thickness, temperature rise and traction coefficient in contact zone by using a thermal elastohydrodynamic lubrication (EHL) model for finite line contact. Concretely, the effects of the equivalent curvature radius of the bush and the pin, and the length of the bush are investigated. Design/methodology/approach In this paper, the contact between the bush and pin is simplified as finite line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. A constitutive equation Ree–Eyring fluid is used in the calculations. Findings It is found that by selecting an optimal equivalent radius of curvature and prolonging the bush length can improve the lubrication state effectively. Originality/value Under specific working conditions, there exists an optimal equivalent radius to maximize the minimum oil film thickness in the contact zone. The increase of generatrix length will weaken the stress concentration effect in the rounded corner area at both ends of the bush, which can improve the wear resistance of chain. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2019-0448.

An adjustable oil film thickness test rig for detecting lubrication characteristics of slipper/swash-pair in piston pumps

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Haiji Wang ◽  
Guanglin Shi
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Relative Error ◽  
Mathematical Analysis ◽  
Test Rig ◽  
Content Type ◽  
Oil Film ◽  
Displacement Sensors ◽  
Measuring Machine ◽  
Lubrication Characteristics

Purpose The purpose of this paper is to propose an adjustable oil film thickness test rig for detecting lubrication characteristics of the slipper. The mathematical analysis of lubrication is introduced. Based on the results from the test rig, the results comparison from test rig and mathematical analysis is carried out. Design/methodology/approach This paper introduces a mechanism which can adjust the oil film thickness between the slipper and swash-plate. Feasibility is ensured, and the accuracy of test rig is guaranteed by the three-coordinate measuring machine. Three displacement sensors show the oil film thickness and its shape. The reacting force and torque resulting from oil film can be achieved by three S-type force sensors and a torque sensor, respectively. Findings The relative error of the reacting force is small. The relative error reduces and is acceptable when the deformation of retainer is taken into account. The thickness and tilt angle of oil film have less effect on the reacting force. However, they are significantly impact on torque. Originality/value The test rig proposed in this paper is able to adjust the oil film thickness, which is used to detecting the lubrication characteristics in pump design. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2020-0166/

Sign in / Sign up

Export Citation Format

Share Document