Thermal fluid-structure interaction of PCB configurations during the wave soldering process

2015 ◽  
Vol 27 (1) ◽  
pp. 31-44 ◽  
Author(s):  
M.S. Abdul Aziz ◽  
M.Z. Abdullah ◽  
C.Y. Khor
Keyword(s):  
Integrated Circuit ◽  
Printed Circuit Boards ◽  
Molten Solder ◽  
Circuit Boards ◽  
Fluid Structure ◽  
Content Type ◽  
Thermally Induced ◽  
C Language ◽  
Soldering Process ◽  
Wave Soldering

Purpose – This paper aims to investigate the thermal fluid–structure interactions (FSIs) of printed circuit boards (PCBs) at different component configurations during the wave soldering process and experimental validation. Design/methodology/approach – The thermally induced displacement and stress on the PCB and its components are the foci of this study. Finite volume solver FLUENT and finite element solver ABAQUS, coupled with a mesh-based parallel code coupling interface, were utilized to perform the analysis. A sound card PCB (138 × 85 × 1.5 mm3), consisting of a transistor, diode, capacitor, connector and integrated circuit package, was built and meshed by using computational fluid dynamics pre-processing software. The volume of fluid technique with the second-order upwind scheme was applied to track the molten solder. C language was utilized to write the user-defined functions of the thermal profile. The structural solver analyzed the temperature distribution, displacement and stress of the PCB and its components. The predicted temperature was validated by the experimental results. Findings – Different PCB component configurations resulted in different temperature distributions, thermally induced stresses and displacements to the PCB and its components. Results show that PCB component configurations significantly influence the PCB and yield unfavorable deformation and stress. Practical implications – This study provides PCB designers with a profound understanding of the thermal FSI phenomenon of the process control during wave soldering in the microelectronics industry. Originality/value – This study provides useful guidelines and references by extending the understanding on the thermal FSI behavior of molten solder for PCBs. This study also explores the behaviors and influences of PCB components at different configurations during the wave soldering process.

Experimental measurements of the shear force on surface mount components simulating the wave soldering process

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Violeta Carvalho ◽  
Bruno Arcipreste ◽  
Delfim Soares ◽  
Luís Ribas ◽  
Nelson Rodrigues ◽  
...  
Keyword(s):  
Printed Circuit Boards ◽  
Deep Understanding ◽  
Critical Issue ◽  
Circuit Boards ◽  
Content Type ◽  
Surface Mount ◽  
Soldering Process ◽  
Wave Soldering ◽  
Pull Out ◽  
Minimum Force

Purpose This study aims to determine the minimum force required to pull out a surface mount component in printed circuit boards (PCBs) during the wave soldering process through both experimental and numerical procedures. Design/methodology/approach An efficient experimental technique was proposed to determine the minimum force required to pull out a surface mount component in PCBs during the wave soldering process. Findings The results showed that the pullout force is approximately 0.4 N. Comparing this value with the simulated force exerted by the solder wave on the component ( ≅ 0.001158 N), it can be concluded that the solder wave does not exert sufficient force to remove a component. Originality/value This study provides a deep understanding of the wave soldering process regarding the component pullout, a critical issue that usually occurs in the microelectronics industry during this soldering process. By applying both accurate experimental and numerical approaches, this study showed that more tests are needed to evaluate the main cause of this problem, as well as new insights were provided into the depositing process of glue dots on PCBs.

Numerical Modeling of the Wave Soldering Process and Experimental Validation

2021 ◽  
Author(s):  
Violeta Carvalho ◽  
Bruno Arcipreste ◽  
Delfim Soares ◽  
Luís Ribas ◽  
Nelson Rodrigues ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Printed Circuit Boards ◽  
Fluid Dynamic ◽  
Circuit Boards ◽  
Electronic Components ◽  
Effective Technique ◽  
Soldering Process ◽  
Wave Soldering ◽  
Air Interface ◽  
Good Agreement

Abstract One of the most important procedures in the electronics industry is the assembly of electronic components onto Printed Circuit Boards (PCB) through the soldering process. Among the various soldering methods available, wave soldering is a very effective technique. In this process, the components are placed onto the PCB, which subsequently, is coated with flux and then passed across a preheat zone. In the end, the assembly is moved by the conveyor and passed over the surface of the molten solder wave in order to create a reliable connection both mechanically and electrically. Although this process has been frequently used, there are soldering defects that remain unsolved and continue to emerge, such as the missing of surface-mount components in the PCB after the soldering process. Aiming to understand if such defects are related to the force exerted by the solder wave in the PCB, in the present work, a numerical and experimental study was performed. For this purpose, a Computational Fluid Dynamic model was developed by using the Fluent® software to describe the interaction between the solder jet and the PCB with the integrated circuits, and the multiphase method, Volume of Fluid, was also applied to track the solder-air interface boundary. The results obtained numerically were validated by using an experimental setup designed and built to this end. In general, the data obtained showed to be in good agreement and it was concluded that the force exerted by the solder wave is approximately 0.02 N.

scholarly journals Thermal Fluid-Structure Interaction in the Effects of Pin-Through-Hole Diameter during Wave Soldering

2014 ◽  
Vol 6 ◽  
pp. 275735 ◽  
Author(s):  
M. S. Abdul Aziz ◽  
M. Z. Abdullah ◽  
C. Y. Khor ◽  
Z. M. Fairuz ◽  
A. M. Iqbal ◽  
...  
Keyword(s):  
Capillary Flow ◽  
Flow Behavior ◽  
Fluid Structure Interaction ◽  
Molten Solder ◽  
Circuit Board ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Soldering Process ◽  
Wave Soldering ◽  
Through Hole

An effective simulation approach is introduced in this paper to study the thermal fluid-structure interaction (thermal FSI) on the effect of pin-through-hole (PTH) diameter on the wave soldering zone. A 3D single PTH connector and a printed circuit board model were constructed to investigate the capillary flow behavior when passing through molten solder (63SnPb37). In the analysis, the fluid solver FLUENT was used to solve and track the molten solder advancement using the volume of fluid technique. The structural solver ABAQUS was used to examine the von Mises stress and displacement of the PTH connector in the wave soldering process. Both solvers were coupled by MpCCI software. The effects of six different diameter ratios (0.1 < d/ D < 0.97) were studied through a simulation modeling. The use of ratio d/ D = 0.2 yielded a balanced filling profile and low thermal stress. Results revealed that filling level, temperature, and displacement exhibited polynomial behavior to d/ D. Stress of pin varied quadratically with the d/ D. The predicted molten solder profile was validated by experimental results. The simulation results are expected to provide better visualization and understanding of the wave soldering process by considering the aspects of thermal FSI.

Path optimization of CNC PCB drilling using hybrid Taguchi genetic algorithm

Kybernetes ◽  
2016 ◽  
Vol 45 (1) ◽  
pp. 107-125 ◽  
Author(s):  
Dony Hidayat Al-Janan ◽  
Tung-Kuan Liu
Keyword(s):  
Genetic Algorithm ◽  
Printed Circuit Boards ◽  
Numerical Control ◽  
Circuit Boards ◽  
Improved Genetic Algorithm ◽  
Solution Quality ◽  
Content Type ◽  
Neighbor Search ◽  
Feasible Solutions ◽  
The Traveling Salesman Problem

Purpose – In this study, the hybrid Taguchi genetic algorithm (HTGA) was used to optimize the computer numerical control-printed circuit boards drilling path. The optimization was performed by searching for the shortest route for the drilling path. The number of feasible solutions is exponentially related to the number of hole positions. The paper aims to discuss these issues. Design/methodology/approach – Therefore, a traveling cutting tool problem (TCP), which is similar to the traveling salesman problem, was used to evaluate the drilling path; this evaluation is considered an NP-hard problem. In this paper, an improved genetic algorithm embedded in the Taguchi method and a neighbor search method are proposed for improving the solution quality. The classical TCP problems proposed by Lim et al. (2014) were used for validating the performance of the proposed algorithm. Findings – Results showed that the proposed algorithm outperforms a previous study in robustness and convergence speed. Originality/value – The HTGA has not been used for optimizing the drilling path. This study shows that the HTGA can be applied to complex problems.

Thermal decomposition of solder flux activators under simulated wave soldering conditions

2017 ◽  
Vol 29 (3) ◽  
pp. 133-143 ◽  
Author(s):  
Kamila Piotrowska ◽  
Morten Stendahl Jellesen ◽  
Rajan Ambat
Keyword(s):  
Thermal Treatment ◽  
Heat Exposure ◽  
Copper Surface ◽  
Substrate Material ◽  
Content Type ◽  
Soldering Process ◽  
Wave Soldering ◽  
Solder Flux ◽  
Solder Mask ◽  
The Impact

Purpose The aim of this work is to investigate the decomposition behaviour of the activator species commonly used in the wave solder no-clean flux systems and to estimate the residue amount left after subjecting the samples to simulated wave soldering conditions. Design/methodology/approach Changes in the chemical structure of the activators were studied using Fourier transform infrared spectroscopy technique and were correlated to the exposure temperatures within the range of wave soldering process. The amount of residue left on the surface was estimated using standardized acid-base titration method as a function of temperature, time of exposure and the substrate material used. Findings The study shows that there is a possibility of anhydride-like species formation during the thermal treatment of fluxes containing weak organic acids (WOAs) as activators (succinic and DL-malic). The decomposition patterns of solder flux activators depend on their chemical nature, time of heat exposure and substrate materials. Evaporation of the residue from the surface of different materials (laminate with solder mask, copper surface or glass surface) was found to be more pronounced for succinic-based solutions at highest test temperatures than for adipic acid. Less left residue was found on the laminate surface with solder mask (∼5-20 per cent of initial amount at 350°C) and poorest acid evaporation was noted for glass substrates (∼15-90 per cent). Practical implications The findings are attributed to the chemistry of WOAs typically used as solder flux activators. The results show the importance WOA type in relation to its melting/boiling points and the impact on the residual amount of contamination left after soldering process. Originality/value The results show that the evaporation of the flux residues takes place only at significantly high temperatures and longer exposure times are needed compared to the temperature range used for the wave soldering process. The extended time of thermal treatment and careful choice of fluxing technology would ensure obtaining more climatically reliable product.

Non-destructive detection methods for discontinuities of interconnection structures

2016 ◽  
Vol 33 (1) ◽  
pp. 23-35 ◽  
Author(s):  
Tomas Blecha
Keyword(s):  
Transmission Lines ◽  
Printed Circuit Boards ◽  
Characteristic Impedance ◽  
Diagnostic Methods ◽  
Detection Methods ◽  
Circuit Boards ◽  
Content Type ◽  
Multiple Line ◽  
Detection And Localization ◽  
Non Destructive

Purpose – The purpose of this paper is to demonstrate the non-destructive methods for detection and localization of interconnection structure discontinuities based on the signal analysis in the frequency and time domain. Design/methodology/approach – The paper deals with the discontinuity characterization of interconnection structures created on substrates used for electronics, and methods for their detection and localization, based on the frequency analysis of transmitted signals. Used analyses are based on the theoretical approach for the solution of discontinuity electrical parameters and are the base for diagnostic methods of discontinuity identification. Findings – The measurement results of reflection parameters, frequency spectrums of transmitted signals and characteristic impedance values are presented on test samples containing multiple line cracks and their width reduction. Practical implications – Obtained results can be used practically, not only for the detection of transmission lines discontinuities on printed circuit boards but also in other applications, such as the quality assessment of bonded joints. Originality/value – Developed methods allow the quick identification and localization of particular discontinuities without the destruction of tested devices.

New technologies of multi-layered printed circuit boards, intended of rapid-design electronic modules

Circuit World ◽  
2015 ◽  
Vol 41 (3) ◽  
pp. 121-124
Author(s):  
Wojciech Stęplewski ◽  
Mateusz Mroczkowski ◽  
Radoslav Darakchiev ◽  
Konrad Futera ◽  
Grażyna Kozioł
Keyword(s):  
Printed Circuit Boards ◽  
New Technologies ◽  
Circuit Board ◽  
Circuit Boards ◽  
Content Type ◽  
Signal Distribution ◽  
Printed Circuit ◽  
Rapid Design ◽  
Small Pitch ◽  
Signal Path

Purpose – The purpose of this study was the use of embedded components technology and innovative concepts of the printed circuit board (PCB) for electronic modules containing field-programmable gate array (FPGA) devices with a large number of pins (e.g. Virtex 6, FF1156/RF1156 package, 1,156 pins). Design/methodology/approach – In the multi-layered boards, embedded passive components that support FPGA device input/output (I/O), such as blocking capacitors and pull-up resistors, were used. These modules can be used in rapid design of electronic devices. In the study, the MC16T FaradFlex material was used for the inner capacitive layer. The Ohmega-Ply RCM 25 Ω/sq material was used to manufacture pull-up resistors for high-frequency pins. The embedded components have been connected to pins of the FPGA component by using plated-through holes for capacitors and blind vias for resistors. Also, a technique for a board-to-board joining, by using castellated terminations, is described. Findings – The fully functional modules for assembly of the FPGA were manufactured. Achieved resistance of embedded micro resistors, as small as the smallest currently used surface-mount device components (01005), was below required tolerance of 10 per cent. Obtained tolerance of capacitors was less than 3 per cent. Use of embedded components allowed to replace the pull-up resistors and blocking capacitors and shortens the signal path from the I/O of the FPGA. Correct connection to the castellated terminations with a very small pitch was also obtained. This allows in further planned studies to create a full signal distribution system from the FPGA without the use of unreliable plug connectors in aviation and space technology. Originality/value – This study developed and manufactured several innovative concepts of signal distribution from printed circuit boards. The signal distribution solutions were integrated with embedded components, which allowed for significant reduction in the signal path. This study allows us to build the target object that is the module for rapid design of the FPGA device. Usage of a pre-designed module would lessen the time needed to develop a FPGA-based device, as a significant part of the necessary work (mainly designing the signal and power fan-out) will already be done during the module development.

Sign in / Sign up

Export Citation Format

Share Document