Bright Electron Beam from Graphite Nano-needle Cold Cathodes and Their Applications to Electron Beam Devices

2006 ◽  
Author(s):  
T. Matsumoto ◽  
Y. Neo ◽  
H. Kume ◽  
H. Mimura
Keyword(s):  
Electron Beam ◽  
Cold Cathodes

scholarly journals Investigation of the Effect of Structural Properties of a Vertically Standing CNT Cold Cathode on Electron Beam Brightness and Resolution of Secondary Electron Images

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1918
Author(s):  
Ha Rim Lee ◽  
Da Woon Kim ◽  
Alfi Rodiansyah ◽  
Boklae Cho ◽  
Joonwon Lim ◽  
...  
Keyword(s):  
Electron Beam ◽  
Structural Properties ◽  
Field Emission ◽  
Secondary Electron ◽  
Structural Features ◽  
Cold Cathode ◽  
Sem Images ◽  
Theoretical Simulation ◽  
Field Emission Properties ◽  
Cold Cathodes

Carbon nanotube (CNT)-based cold cathodes are promising sources of field emission electrons for advanced electron devices, particularly for ultra-high-resolution imaging systems, due to their high brightness and low energy spread. While the electron field emission properties of single-tip CNT cathodes have been intensively studied in the last few decades, a systematic study of the influencing factors on the electron beam properties of CNT cold cathodes and the resolution of the secondary electron images has been overlooked in this field. Here, we have systematically investigated the effect of the structural properties of a CNT cold cathode on the electron beam properties and resolution of secondary electron microscope (SEM) images. The aspect ratio (geometric factor) and the diameter of the tip of a vertically standing CNT cold cathode significantly affect the electron beam properties, including the beam size and brightness, and consequently determine the resolution of the secondary electron images obtained by SEM systems equipped with a CNT cold cathode module. Theoretical simulation elucidated the dependence of the structural features of CNT cold cathodes and electron beam properties on the contribution of edge-emitted electrons to the total field emission current. Investigating the correlations between the structural properties of CNT cold cathodes, the properties of the emitted electron beams, and the resolution of the secondary electron images captured by SEM equipped with CNT cold cathode modules is highly important and informative as a basic model.

Electron beam sources with cold cathodes based on DC high-voltage glow-discharges for PVD applications

2008 ◽  
Author(s):  
Peter Feinaugle ◽  
Gosta Mattausch ◽  
Frank-Holm Rogner ◽  
Vitaly Melnyk ◽  
Igor Melnyk ◽  
...  
Keyword(s):  
Electron Beam ◽  
High Voltage ◽  
Cold Cathodes ◽  
Glow Discharges

Techniques for Transmission Electron Microscopy of Fiber-Matrix Interfaces in Aluminum Alloy-Boron Composites by Ion Erosio

1971 ◽  
Vol 29 ◽  
pp. 204-205
Author(s):  
G. G. Shaw
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Aluminum Alloy ◽  
Electron Beam ◽  
Pure Aluminum ◽  
Ion Milling ◽  
Transmission Electron ◽  
Fiber Matrix ◽  
Ion Erosion ◽  
Row Of Fibers

The morphology and composition of the fiber-matrix interface can best be studied by transmission electron microscopy and electron diffraction. For some composites satisfactory samples can be prepared by electropolishing. For others such as aluminum alloy-boron composites ion erosion is necessary.When one wishes to examine a specimen with the electron beam perpendicular to the fiber, preparation is as follows: A 1/8 in. disk is cut from the sample with a cylindrical tool by spark machining. Thin slices, 5 mils thick, containing one row of fibers, are then, spark-machined from the disk. After spark machining, the slice is carefully polished with diamond paste until the row of fibers is exposed on each side, as shown in Figure 1.In the case where examination is desired with the electron beam parallel to the fiber, preparation is as follows: Experimental composites are usually 50 mils or less in thickness so an auxiliary holder is necessary during ion milling and for easy transfer to the electron microscope. This holder is pure aluminum sheet, 3 mils thick.

Temperature Dependence of the Critical Electron Dose for Fatty Acid Monolayers

1982 ◽  
Vol 40 ◽  
pp. 78-79
Author(s):  
Kenneth H. Downing ◽  
Robert M. Glaeser
Keyword(s):  
Electron Beam ◽  
Fatty Acid ◽  
Inelastic Scattering ◽  
Temperature Dependence ◽  
Structural Damage ◽  
Direct Result ◽  
Second Step ◽  
Strong Temperature Dependence ◽  
Electron Dose ◽  
Covalent Bonds

The structural damage of molecules irradiated by electrons is generally considered to occur in two steps. The direct result of inelastic scattering events is the disruption of covalent bonds. Following changes in bond structure, movement of the constituent atoms produces permanent distortions of the molecules. Since at least the second step should show a strong temperature dependence, it was to be expected that cooling a specimen should extend its lifetime in the electron beam. This result has been found in a large number of experiments, but the degree to which cooling the specimen enhances its resistance to radiation damage has been found to vary widely with specimen types.

Lithography below 100 nm

1983 ◽  
Vol 41 ◽  
pp. 96-99
Author(s):  
L. D. Jackel
Keyword(s):  
Spatial Distribution ◽  
Electron Beam ◽  
Electron Scattering ◽  
Electron Beam Lithography ◽  
Substrate Material ◽  
Local Electron ◽  
Electron Dose ◽  
Positive Resist ◽  
Exposure Process

Most production electron beam lithography systems can pattern minimum features a few tenths of a micron across. Linewidth in these systems is usually limited by the quality of the exposing beam and by electron scattering in the resist and substrate. By using a smaller spot along with exposure techniques that minimize scattering and its effects, laboratory e-beam lithography systems can now make features hundredths of a micron wide on standard substrate material. This talk will outline sane of these high- resolution e-beam lithography techniques.We first consider parameters of the exposure process that limit resolution in organic resists. For concreteness suppose that we have a “positive” resist in which exposing electrons break bonds in the resist molecules thus increasing the exposed resist's solubility in a developer. Ihe attainable resolution is obviously limited by the overall width of the exposing beam, but the spatial distribution of the beam intensity, the beam “profile” , also contributes to the resolution. Depending on the local electron dose, more or less resist bonds are broken resulting in slower or faster dissolution in the developer.

Domain Formation in Synthetic Quartz

1971 ◽  
Vol 29 ◽  
pp. 156-157
Author(s):  
Joseph J. Comer
Keyword(s):  
Electron Beam ◽  
Room Temperature ◽  
Domain Formation ◽  
Synthetic Quartz ◽  
Transmission Electron ◽  
Black Spots ◽  
Diffraction Mode ◽  
Domain Boundaries ◽  
Kikuchi Lines ◽  
Straight Lines

Domains visible by transmission electron microscopy, believed to be Dauphiné inversion twins, were found in some specimens of synthetic quartz heated to 680°C and cooled to room temperature. With the electron beam close to parallel to the [0001] direction the domain boundaries appeared as straight lines normal to <100> and <410> or <510> directions. In the selected area diffraction mode, a shift of the Kikuchi lines was observed when the electron beam was made to traverse the specimen across a boundary. This shift indicates a change in orientation which accounts for the visibility of the domain by diffraction contrast when the specimen is tilted. Upon exposure to a 100 KV electron beam with a flux of 5x 1018 electrons/cm2sec the boundaries are rapidly decorated by radiation damage centers appearing as black spots. Similar crystallographio boundaries were sometimes found in unannealed (0001) quartz damaged by electrons.

Materials for Electron Beam Information Storage

1969 ◽  
Vol 27 ◽  
pp. 152-153 ◽  
Author(s):  
D. E. Speliotis
Keyword(s):  
Magnetic Field ◽  
Electron Beam ◽  
Recent Literature ◽  
Electron Beams ◽  
Information Storage ◽  
The Subject ◽  
The Magnetic Field

The interaction of electron beams with a large variety of materials for information storage has been the subject of numerous proposals and studies in the recent literature. The materials range from photographic to thermoplastic and magnetic, and the interactions with the electron beam for writing and reading the information utilize the energy, or the current, or even the magnetic field associated with the electron beam.

Application of Improved Voltage Compensation in the SEM to Imaging of Organic Materials

1973 ◽  
Vol 31 ◽  
pp. 444-445
Author(s):  
P.J. Killingworth ◽  
M. Warren
Keyword(s):  
Electron Beam ◽  
Organic Materials ◽  
Operating Parameters ◽  
Low Density ◽  
Beam Diameter ◽  
Incident Electron Beam ◽  
Specimen Material ◽  
Voltage Compensation ◽  
Selection Of ◽  
Scanning Electron

Ultimate resolution in the scanning electron microscope is determined not only by the diameter of the incident electron beam, but by interaction of that beam with the specimen material. Generally, while minimum beam diameter diminishes with increasing voltage, due to the reduced effect of aberration component and magnetic interference, the excited volume within the sample increases with electron energy. Thus, for any given material and imaging signal, there is an optimum volt age to achieve best resolution.In the case of organic materials, which are in general of low density and electric ally non-conducting; and may in addition be susceptible to radiation and heat damage, the selection of correct operating parameters is extremely critical and is achiev ed by interative adjustment.

Sign in / Sign up

Export Citation Format

Share Document