Super-Hydrophobic Film Deposition on Epoxy Resin by Nanosecond Pulse Excited Ar/Hmdso Jet Array*

Gonadotroph cell adenomas of the pituitary are infrequent in human patients and are not invariably associated with altered gonadal function. To date, no animal model of this tumor type exists. Herein, we describe spontaneous gonadotroph cell adenomas in old male and female Sprague-Dawley rats by histology, immunocytology and electron microscopy.The material consisted of the pituitaries of 27 male and 38 female Sprague Dawley rats, all 26 months of age or older, removed at routine autopsy. Sections of formal in-fixed, paraffin-embedded tissue were stained with hematoxylin-phloxine-saffron (HPS), the PAS method and the Gordon-Sweet technique for the demonstration of reticulin fibers. For immunostaining, sections were exposed to anti-rat β-LH, anti-ratβ-TSH, anti-rat PRL, anti-rat GH and anti-rat ACTH 1-39. For electron microscopy, tissue was fixed in 2.5% glutaraldehyde, postfixed in 1% OsO4 and embedded in epoxy-resin. Tissue fixed in 10% formalin, embedded in epoxy resin without osmification, was used for immunoelectron microscopy.

Download Full-text

Characterization of Sputtered Films using the Scanning Electron Microscope

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100070667 ◽

1973 ◽

Vol 31 ◽

pp. 44-45

Author(s):

R. F. Schneidmiller ◽

W. F. Thrower ◽

C. Ang

Keyword(s):

Electron Microscope ◽

Scanning Electron Microscope ◽

Thin Film Deposition ◽

Film Deposition ◽

Sputtered Films ◽

Plasma Sputtering ◽

Microelectronic Devices ◽

Control Film ◽

Scanning Electron

Solid state materials in the form of thin films have found increasing structural and electronic applications. Among the multitude of thin film deposition techniques, the radio frequency induced plasma sputtering has gained considerable utilization in recent years through advances in equipment design and process improvement, as well as the discovery of the versatility of the process to control film properties. In our laboratory we have used the scanning electron microscope extensively in the direct and indirect characterization of sputtered films for correlation with their physical and electrical properties.Scanning electron microscopy is a powerful tool for the examination of surfaces of solids and for the failure analysis of structural components and microelectronic devices.

Download Full-text

Surface Structure in Microtomed Sections Caused by Glass and Diamond Knives

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100066334 ◽

1971 ◽

Vol 29 ◽

pp. 456-457

Author(s):

J. Temple Black ◽

William G. Boldosser

Keyword(s):

Plastic Deformation ◽

Epoxy Resin ◽

Carbon Coating ◽

Surface Damage ◽

Body Angle ◽

Normal Manner ◽

Bottom Side ◽

Cutting Direction ◽

Made In ◽

Diamond Knife

Ultramicrotomy produces plastic deformation in the surfaces of microtomed TEM specimens which can not generally be observed unless special preparations are made. In this study, a typical biological composite of tissue (infundibular thoracic attachment) infiltrated in the normal manner with an embedding epoxy resin (Epon 812 in a 60/40 mixture) was microtomed with glass and diamond knives, both with 45 degree body angle. Sectioning was done in Portor Blum Mt-2 and Mt-1 microtomes. Sections were collected on formvar coated grids so that both the top side and the bottom side of the sections could be examined. Sections were then placed in a vacuum evaporator and self-shadowed with carbon. Some were chromium shadowed at a 30 degree angle. The sections were then examined in a Phillips 300 TEM at 60kv.Carbon coating (C) or carbon coating with chrom shadowing (C-Ch) makes in effect, single stage replicas of the surfaces of the sections and thus allows the damage in the surfaces to be observable in the TEM. Figure 1 (see key to figures) shows the bottom side of a diamond knife section, carbon self-shadowed and chrom shadowed perpendicular to the cutting direction. Very fine knife marks and surface damage can be observed.

Download Full-text

Epoxy Resin Embedment

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s042482010010024x ◽

1968 ◽

Vol 26 ◽

pp. 100-101

Author(s):

J. G. Adams ◽

M. M. Campbell ◽

H. Thomas ◽

J. J. Ghldonl

Keyword(s):

Electron Microscopy ◽

Electron Beam ◽

Epoxy Resin ◽

Light Microscope ◽

Epoxy Resins ◽

Image Contrast ◽

Tissue Preservation ◽

Resin System ◽

Excellent Quality

Since the introduction of epoxy resins as embedding material for electron microscopy, the list of new formulations and variations of widely accepted mixtures has grown rapidly. Described here is a resin system utilizing Maraglas 655, Dow D.E.R. 732, DDSA, and BDMA, which is a variation of the mixtures of Lockwood and Erlandson. In the development of the mixture, the Maraglas and the Dow resins were tested in 3 different volumetric proportions, 6:4, 7:3, and 8:2. Cutting qualities and characteristics of stability in the electron beam and image contrast were evaluated for these epoxy mixtures with anhydride (DDSA) to epoxy ratios of 0.4, 0.55, and 0.7. Each mixture was polymerized overnight at 60°C with 2% and 3% BDMA.Although the differences among the test resins were slight in terms of cutting ease, general tissue preservation, and stability in the beam, the 7:3 Maraglas to D.E.R. 732 ratio at an anhydride to epoxy ratio of 0.55 polymerized with 3% BDMA proved to be most consistent. The resulting plastic is relatively hard and somewhat brittle which necessitates trimming and facing the block slowly and cautiously to avoid chipping. Sections up to about 2 microns in thickness can be cut and stained with any of several light microscope stains and excellent quality light photomicrographs can be taken of such sections (Fig. 1).

Download Full-text