Algebraic summation of eigenstates as a novel output metric to extend the linear sensing range of mode-localized sensors

Author(s):  
Hemin Zhang ◽  
Jiming Zhong ◽  
Jing Yang ◽  
Weizheng Yuan ◽  
Hao Kang ◽  
...  
Author(s):  
Toshihiro HORI ◽  
Tomotaka WADA ◽  
Norie UCHITOMI ◽  
Kouichi MUTSUURA ◽  
Hiromi OKADA

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Guangzhong Ma ◽  
Runli Liang ◽  
Zijian Wan ◽  
Shaopeng Wang

AbstractQuantification of molecular interactions on a surface is typically achieved via label-free techniques such as surface plasmon resonance (SPR). The sensitivity of SPR originates from the characteristic that the SPR angle is sensitive to the surface refractive index change. Analogously, in another interfacial optical phenomenon, total internal reflection, the critical angle is also refractive index dependent. Therefore, surface refractive index change can also be quantified by measuring the reflectivity near the critical angle. Based on this concept, we develop a method called critical angle reflection (CAR) imaging to quantify molecular interactions on glass surface. CAR imaging can be performed on SPR imaging setups. Through a side-by-side comparison, we show that CAR is capable of most molecular interaction measurements that SPR performs, including proteins, nucleic acids and cell-based detections. In addition, we show that CAR can detect small molecule bindings and intracellular signals beyond SPR sensing range. CAR exhibits several distinct characteristics, including tunable sensitivity and dynamic range, deeper vertical sensing range, fluorescence compatibility, broader wavelength and polarization of light selection, and glass surface chemistry. We anticipate CAR can expand SPR′s capability in small molecule detection, whole cell-based detection, simultaneous fluorescence imaging, and broader conjugation chemistry.


2021 ◽  
pp. 1-1
Author(s):  
Valliammai Palaniappan ◽  
Masoud Panahi ◽  
Dinesh Maddipatla ◽  
Xingzhe Zhang ◽  
Simin Masihi ◽  
...  

2019 ◽  
Vol 21 (29) ◽  
pp. 16329-16336 ◽  
Author(s):  
Suchinder K. Sharma ◽  
Thomas Köhler ◽  
Jan Beyer ◽  
Margret Fuchs ◽  
Richard Gloaguen ◽  
...  

Extending the temperature sensing range up to 865 K using an appropriate choice of excitation wavelength and coupling scheme in a single crystal sample of EuPO4.


Author(s):  
Qiong Tian ◽  
Wenrong Yan ◽  
Tianding CHEN ◽  
Derek Ho

Pressure sensing electronics have gained great attention in human-machine interface, soft robotics, and wearable biomedical applications. However, existing sensor architectures are inadequate in overcoming the classic tradeoff between sensing range,...


Small ◽  
2021 ◽  
pp. 2106906
Author(s):  
Yue Liu ◽  
Juan Tao ◽  
Wenkai Yang ◽  
Yufei Zhang ◽  
Jing Li ◽  
...  

Author(s):  
Л.В. АЛЕКСЕЙЧИК ◽  
Н.В. АНДРИЕВСКИЙ

Представлены результаты численного моделирования частотныххарактеристик квадратурного трехшлейфового моста (КШМ) L-диапазона, выполненного на основе симметричной полосковой линии с воздушным заполнением. Цель работы - установление допустимого уровня вносимых тепловых потерь полосковых линий (или других типов линий передачи), не оказывающих заметного влияния на рабочие характеристики КШМ, удовлетворяющие требуемым параметрам. Метод расчета основан на принципе декомпозиции электрической цепи КШМ на шесть симметричных 6-полюсников, три из которых соответствуют нечетной моде возбуждения КШМ, а три других - четной моде возбуждения КШМ. Алгебраическое суммирование матриц рассеяния указанных мод позволило получить частотные характеристики результирующей S-матрицы рассеяния КШМ. Нормирование S-матрицы к стандартному волновому сопротивлению 50 Ом выполнено с помощью вычисления собственных значений матриц рассеяния эквивалентных 4-полюсников КШМ. Моделирование проведено в среде LabVIEW. The paper presents the results of numerical simulation of the frequency characteristics of the L-range quadrature three-loop bridge (QLB), based on the symmetric striped line with air filling. The purpose of the study is to establish the permissible level of introduced thermal losses of strip lines (or other types of transmission lines) that do not significantly affect the performance characteristics of the QLB, satisfying the required parameters. The calculation method is based on the principle of decomposition of the QLB electric circuit into six symmetric 6-poles, three of which correspond to the odd excitation mode of the QLB, and the other three correspond to the even excitation mode of the QLB. Algebraic summation of the scattering matrices of these modes made it possible to obtain frequency characteristics of the resulting S-scattering matrix of the qLb. The normalization of the S-matrix to the standard wave resistance of 50 Ohms was carried out using the calculation of the eigenvalues of the scattering matrices of equivalent 4-poles of the QLB. The simulation was carried out in the LabVIEW environment.


2021 ◽  
Author(s):  
Minghui Li ◽  
Jun Zhou ◽  
Ruoshan Lei ◽  
Huanping Wang ◽  
Feifei Huang ◽  
...  

Nowadays, there is an enthusiastic effort to develop the luminescent thermometers used for remote and high-sensitivity temperature readout over a wide sensing range. Herein, the Pr3+ and Gd3+ co-doped ZrO2...


2019 ◽  
Vol 12 (2) ◽  
pp. 28-32
Author(s):  
Nicolae Crișan

Abstract This paper presents a method to increase the detection range for RFID readers in the UHF radio band. The design is following especially the ISO 18000-6C standardization demands for the UHF band, operating from 865 to 868 MHz in Europe and from 902 to 928 MHz in North America. These regulations are allowing the RFID tags to operate near the metallic surfaces and in a wider range than its counterparts at lower frequencies. The paper highlights the advantages offered by the array antenna, especially by the beamforming to increase the reader surveillance zone. The paper describes some additional techniques that are allowing the usage of the circular polarization to increase the reader sensing range and to improuve detection. The design starts with simulation and optimization using HFSS and ends with the measurements that validate the simulation results.


Sign in / Sign up

Export Citation Format

Share Document