POTENTIAL OF HIGH QUALITY LIMESTONE AS ADSORBENT FOR IRON AND MANGANESE REMOVAL IN GROUNDWATER

2016 ◽  
Vol 78 (9-4) ◽  
Author(s):  
Nor Azliza Akbar ◽  
Hamidi Abdul Aziz ◽  
Mohd Nordin Adlan
Keyword(s):  
Langmuir Isotherm ◽  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Groundwater Sample ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Quality ◽  
Study Results ◽  
Fe And Mn

Adsorption using low cost of media plays more attention to this current research. Previous literature found that high quality of limestone was effective in removing heavy metals in water and wastewater. In this study, the potential use of limestone media was investigated. Groundwater sample and limestone properties were characterized to determine the physical and chemical composition. The batch experiments were conducted to determine the effect of varied dosage and contact time.   Analysis on isotherm and kinetic was carried out in this study. Batch study results showed that the maximum removal of both Fe and Mn was greater than 95 and 80% respectively which occurs at optimum dosage of 40g. Moreover, the optimum contact time of Fe and Mn was 90 and 120 minutes, respectively. At the optimum contact time, 96.8% of Fe and 87.4 % of Mn was removed using limestone adsorbent media. In isotherm study, the result revealed that Langmuir isotherm fitted the experimental data better than Freundlich isotherm for both Fe and Mn adsorption. In Langmuir isotherm, the maximum adsorption capacity for both Fe and Mn were 0.018mg/g and 0.011mg/g. Based on kinetic study, the removal of Fe and Mn followed the pseudo-second order kinetic model which R2 (>0.99) greater than in pseudo-first order. This indicates that the chemisorption is the mechanism of adsorption, which contributed to the Fe and Mn removal from the groundwater sample. Thus, from these results, limestone could be used as an alternative for the removal of Fe and Mn from groundwater

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

scholarly journals Adsorption, Equilibrium and Kinetic Studies of the Removal of Methyl Violet from Aqueous Solution Using White Potato Peel Powder

2018 ◽  
Vol 80 ◽  
pp. 17-29 ◽  
Author(s):  
Conrad Kenechukwu Enenebeaku ◽  
Ikechukwu C. Ukaga ◽  
Nnaemeka John Okorocha ◽  
Benedict Ikenna Onyeachu
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Methyl Violet ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Operational Parameters ◽  
Potato Peel ◽  
White Potato

The adsorption of methyl violet (MV) dye onto white potato Peel powder from aqueous solution was investigated by analyzing the operational parameters such as contact time, adsorbent dosage, initial dye concentration, PH and temperature to observe their effects in the dye adsorption process. The optimum conditions for the adsorption of MV onto the adsorbent (WPPP) was found to be contact time (120 mins), PH (10.0) and temperature (303K) for an initial MV dye concentration of 50mg/l and adsorbent dose of 1.0g. The experimental equilibrium adsorption data of the (MV) dye fitted best and well to the freundlich isotherm model. The maximum adsorption capacity was found to be 17.13mg/g for the adsorption of MV. The kinetic data conforms to the pseudo – second order kinetic model.

scholarly journals REACTIVE AZO DYE ADSORPTION USING ZEOLITIC MATERIAL: CONTACT TIME, pH, TEMPERATURE AND EFFECT OF SALTS

2012 ◽  
Vol 09 (17) ◽  
pp. 48-59
Author(s):  
Carina Pitwak MAGDALENA ◽  
Denise Alves FUNGARO ◽  
Patricia CUNICO
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Dye Adsorption ◽  
Correlation Coefficients ◽  
Coal Ash ◽  
Freundlich Isotherm ◽  
Reactive Dye ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Synthetic Dyes

Textile effluents, when not correctly treated, cause a high impact to the environment. The synthetic dyes are used in the fibber dying process, but part of them is discarded to receiving water body. The adsorption is a technique that has been used successfully for an effective removal of color. In this work, the adsorption of reactive dye Remazol Red RB from aqueous solution using zeolite of coal ash as low cost adsorbent was studied. The zeolite was synthesized by hydrothermal treatment with NaOH solution. The effect of experimental parameters such as contact time, pH, temperature and adding salt was investigated. The kinetics studies indicated that the adsorption followed the pseudo-second-order model with correlation coefficients > 0.99. The equilibrium was reached after 360 min of contact time. The experimental data were analyzed using Langmuir and Freundlich isotherm models and the data fitted well to the Langmuir isotherm. The maximum adsorption capacity of zeolite of coal ash for Remazol Vermelho RB was 1.20 mg g-1 with adsorption efficiency between 75 and 91%. The dye adsorption was more efficient in the presence of salts.

scholarly journals Aqueous Phase Adsorption of Pb (II) Ions onto Hymenoptera sphecidae (Mud-wasp) Nest

2020 ◽  
pp. 21-31
Author(s):  
Donald T. Kukwa ◽  
Peter A. Adie ◽  
Rose E. Kukwa ◽  
Paula D. Kungur
Keyword(s):  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Batch Process ◽  
Second Order ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Adsorbent Dose

Removal of Pb (II) ion from aqueous solution using Hymenoptera sphecidae (mud-wasp) nest was investigated using a batch process. The effect of pH, contact time and adsorbent dose were also investigated. The result showed that the adsorption of Pb (II) ion onto mud-wasp nest was dependent on pH, contact time and adsorbent dose. Adsorption patterns were analysed in terms of three bi-parameter isotherms of Langmuir, Freundlich and Temkin. Freundlich isotherm gave the best fit to the adsorption data with a correlation coefficient of 0.992, while monolayer sorption capacity yielded 41.667 mg/g. Lagergren’s pseudo first-order and pseudo second-order kinetic models were used to test the adsorption kinetics. The kinetic data were well described by the pseudo second-order kinetic model, suggesting that the process was chemisorption type.  The results showed that mud-wasp nest can be used as a low-cost adsorbent for the removal of Pb (II) ion from aqueous solutions.

scholarly journals ADSORPTION OF FLUORIDE USING SIO2 NANOPARTICLES AS ADSORBENT

2020 ◽  
Vol 2 (2) ◽  
pp. 1-9
Author(s):  
Davoud Balarak ◽  
Yousef Mahdavi ◽  
Ali Joghatayi
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Sio2 Nanoparticles ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Initial Concentration ◽  
High Doses

Presence of Fluoride in water is safe and effective when used as directed, but it can be harmful at high doses. In the present paper SiO2 nanoparticles as a adsorbent is used for removal of fluoride from aqueous solution. The effect of various operating parameters such as initial concentration of F-, Contact time, adsorbent dosage and pH were investigated. Equilibrium isotherms were used to identify the possible mechanism of the adsorption process. Maximum adsorption capacity of the SiO2 nanoparticles was 49.95 mg/g at PH=6, contact time 20 min, initial concentration of 25 mg/L, and 25±2 ◦C temperatures, when 99.4% of Fwere removed. The adsorption equilibriums were analyzed by Langmuir and Freundlich isotherm models. It was found that the data fitted to Langmuir (R2=0.992) better than Freundlich (R2=0.943) model. Kinetic analyses were conducted using pseudo first-and second-order models. The regression results showed that the adsorption kinetics was more accurately represented by a pseudo second-order model. These results indicate that SiO2 nanoparticles can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution.

scholarly journals Adsorption of Phenol from Wastewater Using Calcined Magnesium-Zinc-Aluminium Layered Double Hydroxide Clay

2020 ◽  
Vol 12 (10) ◽  
pp. 4273
Author(s):  
Lehlogonolo Tabana ◽  
Shepherd Tichapondwa ◽  
Frederick Labuschagne ◽  
Evans Chirwa
Keyword(s):  
Layered Double Hydroxide ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Treatment Temperature ◽  
Bet Surface Area ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Order Kinetic ◽  
Equilibrium Data ◽  
Double Hydroxide

The presence of priority and emerging aromatic-based pollutants in water sources is of growing concern as they are not bioavailable and are present in reuse plant feed streams. These pollutants have known mutagenic and carcinogenic effects and must therefore be removed. Adsorption has been widely accepted as a suitable remediation technology due to its simplicity. Clay-based adsorbents have attracted significant attention due to their low cost, environmentally benign properties and regeneration potential. The present work focused on the thermal modification of a commercial Layered Double Hydroxide (LDH) clay and its subsequent effectiveness as an adsorbent in the removal of phenol from wastewater. Calcination of the neat clay resulted in the formation of metal oxides with varying phases and crystallinity depending on the treatment temperature. The BET surface area increased by 233% upon calcination at 500 °C. The highest phenol removal (85%) was observed in the clay calcined at 500 °C compared to 10% for the neat clay. Optimization studies revealed a maximum adsorption capacity of 12 mg/g at an adsorbent loading of 10 g/L at pH 7. Phenol adsorption was postulated to occur via a two-stage intercalation and surface adsorption mechanism. The equilibrium data were best fitted on the Freundlich isotherm model which describes heterogeneous adsorption. The adsorption kinetics followed a pseudo-second-order kinetic model with rate constants of 4.4 x 10−3 g/mg.h for the first 12h and 6.1 x 10−3 g/mg.h thereafter.

scholarly journals Adsorption Kinetics for the Removal of Hazardous Dye Congo Red by Biowaste Materials as Adsorbents

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Sumanjit Kaur ◽  
Seema Rani ◽  
Rakesh Kumar Mahajan
Keyword(s):  
Congo Red ◽  
Low Cost ◽  
Correlation Coefficients ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Experimental Conditions ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The present work aims to investigate the removal of dye congo red from aqueous solutions by two low-cost biowaste adsorbents such as ground nut shells charcoal (GNC) and eichhornia charcoal (EC) under various experimental conditions. The effect of contact time, ionic strength, temperature, pH, dye concentration, and adsorbent dose on the removal of dye was studied. The kinetic experimental data were fitted to pseudo-first order, pseudo-second order, intraparticle diffusion, Elovich model, and Bangham’s model. Results imply that adsorption of congo red on these adsorbents nicely followed the second order kinetic model and maximum adsorption capacity was found to be 117.6 and 56.8 mg g−1for GNC and EC at 318 K, however it increases with increase in temperature for both adsorbents. Equilibrium isotherms were analyzed by Langmuir, Freundlich, Temkin, Dubinin and Radushkevich, and Generalized Isotherms. Freundlich isotherm described the isotherm data with high-correlation coefficients. The results of the present study substantiate that biowaste material GNC and EC are promising adsorbents for the removal of the dye congo red.

scholarly journals Adsorption of Phosphate from Aqueous Solution onto Iron-coated Waste Mussel Shell: Physicochemical Characteristics, Kinetic, and Isotherm Studies

2021 ◽  
Vol 11 (5) ◽  
pp. 12831-12842
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Physicochemical Characteristics ◽  
Order Kinetic ◽  
Mussel Shell ◽  
Order Kinetic Model ◽  
Synthetic Solution ◽  
Pseudo Second Order

High amounts of phosphate (PO43–) discharged in receiving water can lead to eutrophication, which endangers life below water and human health. This study elucidates the removal of PO43– from synthetic solution by iron-coated waste mussel shell (ICWMS). The PO43– adsorption by ICWMS was determined at different process parameters, such as initial PO43– concentration (7 mg L−1), solution volume (0.2 L), adsorbent dosage (4, 8, 12, 16, and 20 g), and contact time. The highest efficiency of PO43− removal can reach 96.9% with an adsorption capacity of 0.30 mg g−1 could be obtained after a contact time of 48 h for the use of 20 g of ICWMS. Batch experimental data can be well described by the pseudo-second-order kinetic model (R2 = 0.999) and Freundlich isotherm model (R2 = 0.996), suggesting that chemisorption and multilayer adsorption occurred. The efficiency of PO43– removal from aqueous solution by ICWMS was verified to contribute to applying a new low-cost adsorbent obtained from waste mussel shell in the field of wastewater treatment.

Iron and Manganese Removal from Groundwater Using High Quality Limestone

2015 ◽  
Vol 802 ◽  
pp. 460-465 ◽  
Author(s):  
Nor Azliza Akbar ◽  
Hamidi Abdul Aziz ◽  
Mohd Nordin Adlan
Keyword(s):  
Langmuir Isotherm ◽  
Metal Removal ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Groundwater Sample ◽  
Groundwater Treatment ◽  
Mineral Contents ◽  
Manganese Removal ◽  
Batch Study ◽  
Iron And Manganese

Several techniques are used for iron and manganese removal from groundwater. Among these treatments, adsorption has been proven to be a very effective in metal removal for groundwater treatment. Thus, limestone has been proposed as adsorption media because of its low cost. In this study, the mineral contents of limestone were detected using X-ray fluorescence (XRF). XRF results showed that limestone contains 97.93% CaCO3, 0.87% MgO, and 1.2% other elements. Groundwater sample was obtained from USM borehole located at 5° 08’ 50.5”N and 100° 29’ 34.7”E. A batch study was carried out for various dosages of limestone media (5–50 g) in 200 mL of groundwater sample. The highest iron and manganese removal was more than 90% and 70%, respectively, at optimum dosage of 40 g/200 mL sample. Adsorption data were modeled using Langmuir and Freundlich adsorption isotherms. The batch study result shows that monolayer Langmuir isotherm fitted the experimental data better than the Freundlich isotherm. The correlation coefficient (R2) in the Langmuir isotherm for both metals were 0.84 and 0.97, whereas 0.83 and 0.23 in the Freundlich isotherm, respectively. Based on the present results, application of limestone as adsorbent media can be a good alternative of groundwater treatment because of the low cost of the media. Thus, the use of limestone could help to overcome the excessive iron and manganese problem in water treatment plants.

scholarly journals Parametric Statistical Significance of Iron (II) Ions Adsorption by Coconut Shell in Aqueous Solutions

2019 ◽  
Vol 11 (1) ◽  
pp. 17-25
Author(s):  
Babatope Abimbola Olufemi ◽  
Anne Nlerum
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Statistical Significance ◽  
Freundlich Isotherm ◽  
Coconut Shell ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Sorption Data

The parametric statistical adsorption of chemically unmodified coconut shell powder (CSP) to adsorb iron (II) ions from aqueous solutions was examined in this work. It was observed that the adsorption capacity increased with increasing adsorbent dose, reducing adsorbate dose, increasing contact time, decreasing temperature and reducing particle size. As observed about one gram of the adsorbent was sufficient enough to remove 98 % iron (II) ions. A total contact time of about 40 minutes was sufficient for almost complete adsorption of the ions, while a pH of about 6.0 exhibited the maximum adsorption capacity. The sorption data were fitted into Langmuir, Freundlich, Temkin and the Dubinin-Radushkevich isotherms, fitted most with the Freundlich Isotherm model. The energy values obtained from the Temkin and Dubinin-Radushkevich isotherm model indicated high chemisorption phenomenon with the adsorbents. Investigation of some kinetic models confirmed that the adsorption of iron (II) ions using CSP was a pseudo-second order kinetic process, which further corroborates that chemisorption dominates the adsorption. Fourier Transform Analysis (FTIR) further established and justified the outcome of the study. The adsorption was parametrically justified statistically with Analysis of Variance (ANOVA) and Bonferroni-Holm Posthoc significance test. Conclusively, coconut shell proved strongly to be an effective and suitable adsorbent for removing iron (II) ions from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document