scholarly journals Evaluation of Grape Pomace Composting Process

2014 ◽  
Vol 62 (5) ◽  
pp. 875-881 ◽  
Author(s):  
Patrik Burg ◽  
Tomáš Vítěz ◽  
Jan Turan ◽  
Jana Burgová
Keyword(s):  
Moisture Content ◽  
Bulk Density ◽  
Cross Section ◽  
Significant Influence ◽  
Grape Pomace ◽  
Wood Chips ◽  
Waste Wood ◽  
Composting Process ◽  
The Individual

The paper deals with the problems of composting of grape pomace in strip compost piles. The three variants of compost piles formed from grape pomace and vegetables waste, wood chips and mature in varying proportions were tested. Turning of piles was performed using windrow turner PKS 2.8, in which the achieved performance was monitored. On the performance of windrow turner has a significant influence also cross section or width and height of turning piles and the bulk density of ingredients including their moisture. In evaluating, attention has been paid to assessment of selected parameters (temperature, moisture content) of the composting process. From the viewpoint of temperature course, the highest temperature reached at the piles in Var. I (64.1 °C) and Var. II (55.3 °C). Moisture of compost piles in the individual variants did not differ significantly and ranged between 25–35%.

scholarly journals Parameters of Trucks and Loads in the Transport of Scots Pine Wood Biomass Depending on the Season and Moisture Content of the Load

Forests ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 223
Author(s):  
Grzegorz Trzciński ◽  
Łukasz Tymendorf ◽  
Paweł Kozakiewicz
Keyword(s):  
Moisture Content ◽  
Bulk Density ◽  
Load Capacity ◽  
Wood Chips ◽  
Total Weight ◽  
Wood Biomass ◽  
Four Seasons ◽  
Gross Vehicle Weight ◽  
Bulk Volume ◽  
Average Quantity

Transport of wood biomass is one of the key operations in forestry and in the wood industry. An important part is the transport of shredded wood, where the most common forms are chips and sawdust. The aim of the research was to present the variability of the total weight of trucks (gross vehicle weight, GVW), the weight of the empty trucks (tare), and loads of chips and sawdust in different periods of the year. Changes in specific parameters were analyzed: GVW; tare weight; trailer capacity; use of the trailer load capacity; bulk volume and bulk density of wood biomass loads; solid cubic meter (m3) and weight of 1m3 of the load; and load weight depending on the season, with simultaneous measurements of wood chips and sawdust moisture. More than 250 transports from four seasons of the year were analyzed in the research. It was found that the total weight of trucks (GVW) was at a comparable level, on average from 39.42 to 39.64 Mg with slight differences (with SD 0.29 and 0.39). The weight of empty trucks was 16.15 Mg for chip-bearing trucks and 15.93 Mg for sawdust-bearing trucks (with SD 0.604 and 0.526). The type of wood material has an influence on the transported volume. The average quantity of load in the bulk cubic meter was 64.783 m3 for wood chips (SD 3.127) and 70.465 m3 (SD 2.516) for sawdust. Over 30% differences in the volume of transported wood chips and approximately 18% for sawdust were observed. The use of the loading capacity of the trailer was on average 72.58% (SD 5.567) for the transport of wood chips and 77.42% (SD 3.019) for the transport of sawdust. The sawdust bulk density was from 0.3050 to 0.4265 Mg⋅m−3 for wood chips and 0.3200 to 0.3556 Mg⋅m−3 for sawdust. This parameter is significantly dependent on moisture content, and the determined correlation functions can be used for estimating and predicting bulk density. The abovementioned absolute moisture content of chips and sawdust also depends on the season, which also affects the selected parameters of wood biomass loads.

scholarly journals Some Physical Properties of Palmyrah Palm (Borassus flabellifer L.) Fruits

2021 ◽  
pp. 18-25
Author(s):  
P. C. Vengaiah ◽  
S. Kaleemullah ◽  
M. Madhava ◽  
A. Mani ◽  
B. Sreekanth
Keyword(s):  
Aspect Ratio ◽  
Moisture Content ◽  
Mild Steel ◽  
Physical Properties ◽  
Bulk Density ◽  
Geometric Mean ◽  
Static Friction ◽  
Angle Of Repose ◽  
Average Mass ◽  
The Individual

Some physical properties of palmyrah fruit were investigated in this study. The average values of major, medium, minor and geometric mean diameters of fresh whole palmyrah fruit were 11.54,10.45, 9.85 and 10.64 cm respectively at 47.34 % (w.b) moisture content whereas that of palmyrah nut were 8.59, 7.35, 4.99 and 6.79 cm respectively at 8% (w.b) moisture content. Sphericity, surface area and aspect ratio were found to be 91.94%, 359.17 cm2 and 0.90 for fruit and whereas that of nut were 79.19%, 145.16 cm2 and 0.86 respectively. The average mass of the individual palmyrah fruit and nut was 927.78 and 248.10 g whereas bulk density was 525.92 and 693.0 kg/m3 respectively. The coefficient of static friction on mild steel, glass and plywood surfaces were 0.27, 0.21 and 0.25 for palmyrah fruit and 0.36, 0.28 and 0.27 for nut respectively. The angle of repose of palmyrah fruit and nut were 30.77 and 44.03 respectively.

scholarly journals Wood Chip Drying through the Using of a Mobile Rotary Dryer

Energies ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1590 ◽  
Author(s):  
Angelo Del Giudice ◽  
Andrea Acampora ◽  
Enrico Santangelo ◽  
Luigi Pari ◽  
Simone Bergonzoli ◽  
...  
Keyword(s):  
Moisture Content ◽  
Power Plants ◽  
Black Locust ◽  
Thermal Power ◽  
Initial Moisture Content ◽  
Wood Chip ◽  
Wood Chips ◽  
Cocurrent Flow ◽  
Drying Process ◽  
Rotary Dryer

Drying is a critical point for the exploitation of biomass for energy production. High moisture content negatively affects the efficiency of power generation in combustion and gasification systems. Different types of dryers are available however; it is known that rotary dryers have low cost of maintenance and consume 15% and 30% less in terms of specific energy. The study analyzed the drying process of woody residues using a new prototype of mobile rotary dryer cocurrent flow. Woodchip of poplar (Populus spp.), black locust (Robinia pseudoacacia L.), and grapevine (Vitis vinifera L.) pruning were dried in a rotary drier. The drying cycle lasted 8 h for poplar, 6 h for black locust, and 6 h for pruning of grapevine. The initial biomass had a moisture content of around 50% for the poplar and around 30% for grapevine and black locust. The study showed that some characteristics of the biomass (e.g., initial moisture content, particle size distribution, bulk density) influence the technical parameters (i.e., airflow temperature, rate, and speed) of the drying process and, hence, the energy demand. At the end of the drying process, 17% of water was removed for poplar wood chips and 31% for grapevine and black locust wood chips. To achieve this, result the three-biomass required 1.61 (poplar), 0.86 (grapevine), and 1.12 MJ kgdry solids−1 (black locust), with an efficiency of thermal drying (η) respectively of 37%, 12%, and 27%. In the future, the results obtained suggest an increase in the efficiency of the thermal insulation of the mobile dryer, and the application of the mobile dryer in a small farm, for the recovery of exhaust gases from thermal power plants.

scholarly journals Comparative Study of the Properties of Wood Flour and Wood Pellets Manufactured from Secondary Processing Mill Residues

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2487
Author(s):  
Geeta Pokhrel ◽  
Yousoo Han ◽  
Douglas J. Gardner
Keyword(s):  
Moisture Content ◽  
Bulk Density ◽  
Raw Materials ◽  
Wood Flour ◽  
The United States ◽  
Red Maple ◽  
Wood Pellets ◽  
Secondary Processing ◽  
Material Costs ◽  
Mill Residues

The generation of secondary processing mill residues from wood processing facilities is extensive in the United States. Wood flour can be manufactured utilizing these residues and an important application of wood flour is as a filler in the wood–plastic composites (WPCs). Scientific research on wood flour production from mill residues is limited. One of the greatest costs involved in the supply chain of WPCs manufacturing is the transportation cost. Wood flour, constrained by low bulk densities, is commonly transported by truck trailers without attaining allowable weight limits. Because of this, shipping costs often exceed the material costs, consequently increasing raw material costs for WPC manufacturers and the price of finished products. A bulk density study of wood flour (190–220 kg/m3) and wood pellets (700–750 kg/m3) shows that a tractor-trailer can carry more than three times the weight of pellets compared to flour. Thus, this study focuses on exploring the utilization of mill residues from four wood species in Maine to produce raw materials for manufacturing WPCs. Two types of raw materials for the manufacture of WPCs, i.e., wood flour and wood pellets, were produced and a study of their properties was performed. At the species level, red maple 40-mesh wood flour had the highest bulk density and lowest moisture content. Spruce-fir wood flour particles were the finest (dgw of 0.18 mm). For all species, the 18–40 wood flour mesh size possessed the highest aspect ratio. Similarly, on average, wood pellets manufactured from 40-mesh particles had a lower moisture content, higher bulk density, and better durability than the pellets from unsieved wood flour. Red maple pellets had the lowest moisture content (0.12%) and the highest bulk density (738 kg/m3). The results concluded that the processing of residues into wood flour and then into pellets reduced the moisture content by 76.8% and increased the bulk density by 747%. These material property parameters are an important attempt to provide information that can facilitate the more cost-efficient transport of wood residue feedstocks over longer distances.

scholarly journals The Chosen Aspects of Skew Rolling of Hollow Stepped Shafts

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 764
Author(s):  
Jarosław Bartnicki ◽  
Yingxiang Xia ◽  
Xuedao Shu
Keyword(s):  
Cross Section ◽  
Rolling Mill ◽  
Metal Flow ◽  
Experimental Tests ◽  
Rolling Process ◽  
Numerical Control ◽  
Technological Parameters ◽  
Flow Mechanisms ◽  
The Individual ◽  
Skew Rolling

The paper presents chosen aspects of the skew rolling process of hollow stepped products with the use of a skew rolling mill designed and manufactured at the Lublin University of Technology. This machine is characterized by the numerical control of spacing between the working rolls and the sequence of the gripper axial movement, which allows for the individual programming of the obtained shapes of parts such as stepped axles and shafts. The length of these zones and the values of possibly realizable cross-section reduction and obtained outlines are the subject of this research paper. The chosen results regarding the influence of the technological parameters used on the course of the process are shown in the present study. Numerical modelling using the finite element method in Simufact Forming, as well as the results of experimental tests performed in a skew rolling mill, were applied in the conducted research. The work takes into account the influence of cross-section reduction of the hollow parts and the feed rate per rotation on the metal flow mechanisms in the skew rolling process. The presented results concern the obtained dimensional deviations and changes in the wall thickness determining the proper choice of technological parameters for hollow parts formed by the skew rolling method. Knowledge about the cause of the occurrence of these limitations is very important for the development of this technology and the choice of the process parameters.

scholarly journals Effects of microwave irradiation on the moisture content of various wood chip fractions obtained from different tree species

2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Monika Aniszewska ◽  
Krzysztof Słowiński ◽  
Ewa Tulska ◽  
Witold Zychowicz
Keyword(s):  
Moisture Content ◽  
Microwave Irradiation ◽  
Microwave Power ◽  
Irradiation Time ◽  
Initial Moisture Content ◽  
Radiant Energy ◽  
Wood Chip ◽  
Wood Chips ◽  
Chip Size ◽  
Drying Rates

AbstractThe paper proposes the use of microwave irradiation to lower the initial moisture content of wood chips. The study involved willow and fir chips fractionated by means of a sieve separator and unfractionated ash chips. The wood chips were exposed to a constant microwave power of 800 W for 30 s, 60 s, 120 s and 180 s. The chips were weighed before and after irradiation to measure loss of moisture. It was found that the decline in moisture content increased with wood chip size for a given irradiation time and microwave power. The initial moisture content of wood chips was not found to significantly affect loss of moisture as the drying rates of wood chips with higher and lower moisture content exposed to microwaves were not statistically different. The results showed that irradiation intensity increased with the time of exposure to microwaves and unit radiant energy per unit of evaporated moisture decreased with increasing wood chip size in the 3.15–31.50 mm range.

The Study of Chinese Political Culture

1966 ◽  
Vol 18 (3) ◽  
pp. 503-524 ◽  
Author(s):  
John W. Lewis
Keyword(s):  
Political Culture ◽  
Cross Section ◽  
Scholarly Publication ◽  
Communist China ◽  
The Individual ◽  
Chinese Political Culture

These seven recent works typify a cross section of scholarly publication on the Chinese People's Republic, its history, present operation, and prospects. Taken together, they provide the basis for some remarks on the study of Chinese “political culture.” Rather than attempt a full review of the individual works, this brief article will examine some of their assumptions and indirectly comment on the literature they represent. Each book reflects a prodigious scholarly effort and has received in various other journals a complete appraisal of its intellectual value. In general it may be fairly said that these volumes do not constitute significant breakthroughs of knowledge. They do, however, bring together and analyze important bodies of data on Communist China.

Measuring the Thermo-Technical Parameters of Autoclaved Aerated Concrete

2016 ◽  
Vol 824 ◽  
pp. 100-107 ◽  
Author(s):  
Alena Struhárová
Keyword(s):  
Thermal Conductivity ◽  
Moisture Content ◽  
Physical Properties ◽  
Bulk Density ◽  
Capillary Absorption ◽  
Measuring Device ◽  
Technical Parameters ◽  
Autoclaved Aerated Concrete ◽  
Aerated Concrete ◽  
Technical Properties

Bulk density and moisture content are factors that significantly affect the physical properties of autoclaved aerated concrete (AAC) including thermal conductivity and other thermo-technical characteristics. This article shows the results of measurements of compressive strength, capillary absorption, water absorption and porosity of AAC (ash on fluidized fly ash) at different bulk density and also the results of thermal conductivity of AAC at different bulk density and variable moisture content of the material. The thermo-technical properties were measured using the Isomet 2104, a portable measuring device. Acquired results demonstrate dependence of physical properties including thermal conductivity of AAC on bulk density and moisture content. The reliability and accuracy of the method of measuring was also shown.

Sign in / Sign up

Export Citation Format

Share Document