The Influence of Gear Design Parameters on Gear Tooth Damage Detection Sensitivity

2002 ◽  
Vol 124 (4) ◽  
pp. 794-804 ◽  
Author(s):  
Lin Liu ◽  
Darryll J. Pines
Keyword(s):  
Damage Detection ◽  
Gear Tooth ◽  
Transmission Error ◽  
Spur Gear ◽  
Detection Sensitivity ◽  
Design Parameters ◽  
Gear Design ◽  
Gear Mesh ◽  
Pressure Angle ◽  
Number Of Teeth

This paper develops an analytical model to simulate the gear mesh contact for a spur gear pair with and without tooth damage. Three common gear tooth faults are simulated including pitting, wear and root cracks. The effect of tooth face width on detection sensitivity for pitting and the effect of crack width on detection sensitivity for crack are investigated. Using static performance measures, such as transmission error, results suggest that basic gear design parameters, such as diametral pitch, pressure angle and number of teeth, may have a significant effect on damage detection sensitivity. It appears that a decrease in diametral pitch will enhance damage detection sensitivity for all the three types of damage. An increase in pressure angle or number of teeth will enhance detection sensitivity for pitting damage, but tends to decrease the sensitivity to crack or wear damage.

Further Evaluation of Spur Gear Tooth Profile Designs Used in Heavily Loaded Transmissions

2011 ◽  
Author(s):  
Nihat Yıldırım ◽  
Hakan I˙s¸c¸i ◽  
Abdullah Akpolat
Keyword(s):  
Gear Tooth ◽  
Transmission Error ◽  
Spur Gear ◽  
Tooth Profile ◽  
Design Parameters ◽  
Preference Order ◽  
Spur Gears ◽  
Tooth Root ◽  
Contact Ratio ◽  
Practical Applications

Aerospace applications require special procedures for component design and manufacturing. Spur gears of different designs, because of their simpler geometries, are used in vital units-transmissions of helicopters and alike aerospace vehicles. In this study, performances of various profile designs of previously researched low and high contact ratio spur gears with some realistic design parameters are studied. Effects of the realistic parameters of variable tooth pair stiffness, relief shape, and adjacent pitch error on Transmission Error (TE), tooth loads and root stresses are presented; composition of these parameters determines the efficiency of the gearbox assembly. Detail of minimization of tooth root stress through optimized/proper design of relief is described. More comprehensive comparison of the gear tooth profile design cases is done to be able to guide aerospace transmission designers for practical applications with realistic parameters for each of the design cases. A preference order is done among the design cases, depending on effect of some design parameters on the results such as tooth loads, tooth root stresses, TE curves and peak-to-peak TE values.

scholarly journals Selection of Pressure Angle based on Dynamic Effects in Asymmetric Spur Gear with Fixed Normal Contact Ratio

2019 ◽  
Vol 69 (3) ◽  
pp. 303-310
Author(s):  
Benny Thomas ◽  
K. Sankaranarayansamy ◽  
S. Ramachandra ◽  
Suresh Kumar S.P.
Keyword(s):  
Gear Tooth ◽  
Transmission Error ◽  
Spur Gear ◽  
Dynamic Factor ◽  
Spur Gears ◽  
Contact Ratio ◽  
Normal Contact ◽  
Pressure Angle ◽  
Side Pressure ◽  
Static Transmission Error

Asymmetric spur gears are finding application in many fields including aerospace propulsion and automobile which demand unidirectional or relatively higher load on one side of the gear flank. Design intend to maximise the load carrying capacity of the drive side of asymmetric gear by increasing the pressure angle is achieved at the expense of coast side capacity. Multiple solution for coast to drive side pressure angle exist for a given contact ratio and each of these have relative merits and demerits. In the present work asymmetric spur gears of theoretically equal contact ratio as that of corresponding symmetric gears are selected to investigate the change in gear tooth static transmission error and dynamic behaviour with coast and drive side pressure angle. Study shows that dynamic factor of normal contact ratio asymmetric spur gears below resonance speed are relatively lower than corresponding symmetric gears of same module, contact ratio, number of teeth, coast side pressure angle and fillet radii. Results also show that, coast and drive side pressure angle can be suitably selected for a given contact ratio to reduce the single tooth and double tooth contact static transmission error and dynamic factor of asymmetric spur gears.

scholarly journals An Experimental Investigation of the Impact of Random Spacing Errors on the Dynamic Transmission Error of Spur Gear Pairs

2019 ◽  
Author(s):  
Muhammad Nevin Anandika ◽  
Ahmet Kahraman ◽  
David Talbot
Keyword(s):  
Frequency Spectrum ◽  
Gear Tooth ◽  
Random Sequence ◽  
Transmission Error ◽  
Spur Gear ◽  
Engineering Industry ◽  
Gear Pair ◽  
Gear Mesh ◽  
Dynamic Transmission Error ◽  
The Impact

Abstract Noise and vibration performance of a gear system is critical in any engineering industry. Excessive vibrational amplitudes originated by the excitations at the gear meshes propagate to the transmission housing to cause noticeable noise, while also increasing gear tooth stresses to degrade durability. As such, gear designers must generate designs that are nominally quiet with low-vibration amplitudes. This implies a gear pair fabricated exactly to the specifications of its blue print will be acceptable for its vibration behavior. Achieving this, however, is not sufficient. As the manufacturing of gears require them to be subject to bands of tolerances afforded by the manufacturing processes employed, the designers must be concerned about variations to the performance of their presumably quite baseline designs within these tolerance bands. This research aims at demonstrating how one type of manufacturing error, random tooth spacing errors, alter the vibratory behavior of a spur gear pair. Two pairs of spur gears are tested for their dynamic transmission error performance. One gear pair with no tooth spacing errors form the baseline. The second gear pair contain an intentionally induced random sequence of spacing errors. The forced vibration responses of both gear pairs are compared within wide ranges of speed and torque. This comparison shows that there is a clear and significant impact of random spacing errors on spur gear dynamics, measurable through examination of their respective transmission error signatures. In the off-resonance regions of speed, vibration amplitudes of the random error pair are higher than the no-error baseline spur gear pair. Meanwhile, at or near resonance peaks, the presence of random spacing errors tends to lower the peak amplitudes slightly as compared to the no-error baseline spur gear pair. The presence of random spacing errors introduces substantial harmonic content that are non-mesh harmonics. This results in a broadband frequency spectrum in addition to an otherwise well-defined frequency spectrum with gear-mesh order components, pointing to an additional concern of noise quality.

Nonlinear Dynamic Modeling of Gear-Shaft-Disk-Bearing Systems Using Finite Elements and Describing Functions

2003 ◽  
Vol 126 (3) ◽  
pp. 534-541 ◽  
Author(s):  
Rafiq Maliha ◽  
Can U. Dogˇruer ◽  
H. Nevzat O¨zgu¨ven
Keyword(s):  
Dynamic Model ◽  
Nonlinear Dynamic ◽  
Gear Tooth ◽  
Transmission Error ◽  
Spur Gear ◽  
Degree Of Freedom ◽  
Discrete Models ◽  
Nonlinear Dynamic Model ◽  
Disk System ◽  
Gear Mesh

This study presents a new nonlinear dynamic model for a gear-shaft-disk-bearing system. A nonlinear dynamic model of a spur gear pair is coupled with linear finite element models of shafts carrying them, and with discrete models of bearings and disks. The nonlinear elasticity term resulting from backlash is expressed by a describing function, and a method developed in previous studies to determine multi harmonic responses of nonlinear multi-degree-of-freedom systems is employed for the solution. The excitations considered in the model are external static torque and internal excitation caused by mesh stiffness variation, gear errors and gear tooth profile modifications. The model suggested and the solution method presented combine the versatility of modeling a shaft-bearing-disk system that can have any configuration without a limitation to the total degree of freedom, with the accuracy of a nonlinear gear mesh interface model that allows to predict jumps and double solutions in frequency response. Thus any single stage gear mesh configuration can be modeled easily and accurately. With the model developed it is possible to calculate dynamic gear loads, dynamic bearing forces, dynamic transmission error and bearing displacements. Theoretical results obtained by using the method suggested are compared with the experimental data available in literature, as well as with the theoretical values calculated by employing a previously developed nonlinear single degree of freedom model.

Effect of design parameters on stresses occurring at the tooth root in a spur gear pressed on a shaft

2021 ◽  
pp. 095440892199529
Author(s):  
Fatih Güven
Keyword(s):  
Internal Pressure ◽  
Tangential Stress ◽  
Spur Gear ◽  
Design Parameters ◽  
Interference Fit ◽  
Gear Design ◽  
Compact Design ◽  
Fit Tolerance ◽  
Moderate Stress ◽  
Good Agreement

Gears are commonly used in transmission systems to adjust velocity and torque. An integral gear or an interference fit could be used in a gearbox. Integral gears are mostly preferred as driving gear for a compact design to reduce the weight of the system. Interference fit makes the replacement of damaged gear possible and re-use of the shaft compared to the integral shaft. However, internal pressure occurs between mating surfaces of the components mated. This internal pressure affects the stress distribution at the root and bottom land of the gear. In this case, gear parameters should be re-considered to assure gear life while reducing the size of the gear. In this study, interference fitted gear-shaft assembly was examined numerically. The effects of rim thickness, profile shifting, module and fit tolerance on bending stress occurring at the root of the gear were investigated to optimize gear design parameters. Finite element models were in good agreement with analytical solutions. Results showed that the rim thickness of the gear is the main parameter in terms of tangential stress occurring at the bottom land of the gear. Positive profile shifting reduces the tangential stress while the pitch diameter of the gear remains constant. Also, lower tolerance class could be selected to moderate stress for small rim thickness.

scholarly journals Research on the Design and Modification of Asymmetric Spur Gear

2015 ◽  
Vol 2015 ◽  
pp. 1-13 ◽  
Author(s):  
Xiaohe Deng ◽  
Lin Hua ◽  
Xinghui Han
Keyword(s):  
Computer Aided Design ◽  
Design Method ◽  
Geometric Model ◽  
Simulation Method ◽  
Transmission Error ◽  
Spur Gear ◽  
Geometric Shape ◽  
Spur Gears ◽  
Gear Design ◽  
Aided Design

A design method for the geometric shape and modification of asymmetric spur gear was proposed, in which the geometric shape and modification of the gear can be obtained directly according to the rack-cutter profile. In the geometric design process of the gear, a rack-cutter with different pressure angles and fillet radius in the driving side and coast side was selected, and the generated asymmetric spur gear profiles also had different pressure angles and fillets accordingly. In the modification design of the gear, the pressure angle modification of rack-cutter was conducted firstly and then the corresponding modified involute gear profile was obtained. The geometric model of spur gears was developed using computer-aided design, and the meshing process was analyzed using finite element simulation method. Furthermore, the transmission error and load sharing ratio of unmodified and modified asymmetric spur gears were investigated. Research results showed that the proposed gear design method was feasible and desired spur gear can be obtained through one time rapid machining by the method. Asymmetric spur gear with better transmission characteristic can be obtained via involute modification.

Evaluation of Mechanical and Thermal Stresses in Polymer Gear Teeth through Simulation Approach

2013 ◽  
Vol 302 ◽  
pp. 468-473 ◽  
Author(s):  
Per Lindholm ◽  
Jian Qin
Keyword(s):  
Thermal Properties ◽  
Thermal Stresses ◽  
Material Selection ◽  
Gear Tooth ◽  
Gear Wheel ◽  
Spur Gear ◽  
Contact Forces ◽  
Mechanical And Thermal Properties ◽  
Gear Mesh ◽  
Tensional Stress

One way to achieve lightweight and lubricant-free drive train is, among others, to convert conventional steel to polymer composite materials. This paper describes a part of this endeavor by taking a spur gear pair as a study object. One of the steel gear wheel is replaced with three different materials including Victrex PEEK 650G, Victrex PEEK 650CA30 and Luvocom PEEK 1105-8165 while keeping the gear geometry unchanged. Mechanical stresses and thermal properties are two major criteria for material selection at this stage. Therefore carbon fiber filled PEEK (Victrex PEEK 650CA30) and PEEK filled with thermal conductive minerals (Luvocom 1105-8165) are chosen to benchmark each of the criterion. The evaluation is done by modeling the gear mesh and analyzing the contact forces and heat generated in the gear tooth. The results show surface temperature on the tooth flanks, root tensional stress and contact pressure during the tooth mesh. The work suggests a guideline of materials selection. Depending on actual application a compromisation between mechanical and thermal properties often needs to be considered within the tolerance boundary in order to obtain optimized results. This work only deals with material selection. Gear design such as optimization of tooth geometry for polymer gears is out of the scope of this study and will not be discussed.

Development of High-Loaded, Low-Speed Spiroid Gearboxes

2000 ◽  
Author(s):  
V. I. Goldfarb ◽  
V. M. Spiridonov ◽  
N. S. Golubkov
Keyword(s):  
High Reliability ◽  
Operating Conditions ◽  
Design Parameters ◽  
Angular Range ◽  
Operating Modes ◽  
Gear Design ◽  
Gear Mesh ◽  
Numerical Studies ◽  
High Durability ◽  
Spiroid Gear

Abstract Actuator rotation sometimes is required to transmit considerable torques at low speeds in a limited angular range. Such operating conditions are typical, for example, for the rotational drives of gas pipeline stop valves. These conditions are made worse by increased torques requried at the initial instant of motion when the torque is 1.3 to 1.5 times greater than the nominal torque, and by the range of operating temperatures of −60°C to +50°C. A number of gearboxes with a spiroid gear mesh were developed to satisfy these conditions for different torques (i.e. for different standard stop valves), with the steel spiroid pair case-hardened to 60–62 hardness Rc. A set of numerical studies had been conducted in order to choose gear design parameters and other elements of the gearbox. Experimental research performed using special testing rigs for definite operating modes showed high reliability and wear resistance of the drives developed and their high durability compared to known ones which is of great importance for given application domain.

scholarly journals Analysis on Meshing Characteristics and Transmission Error of Elliptic Gears

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Changbin Dong ◽  
Yongping Liu ◽  
Yongqiao Wei ◽  
Beibei Yun ◽  
Dawei Li ◽  
...  
Keyword(s):  
Great Influence ◽  
Transmission Error ◽  
Spur Gear ◽  
Analysis Model ◽  
Contact Ratio ◽  
Cylindrical Gear ◽  
Pressure Angle ◽  
Object Based ◽  
Meshing Characteristics ◽  
Eccentricity Error

As an important parameter to distinguish noncircular gear from cylindrical gear, eccentricity is very important for the meshing characteristics and transmission error of noncircular gear. In order to study the transmission characteristics of the elliptic gear, a pair of elliptic gear in the reversing device of a new type of drum pumping was taken as the research object. Based on the analysis of the transmission pressure angle and instantaneous contact ratio of the elliptic gear, the eccentricity error was introduced into the analysis model of transmission error. The influences of the eccentricity on the transmission pressure angle, instantaneous contact ratio, and transmission error were analyzed, and the analysis accuracy is verified by the finite element method. The results show that the eccentricity has a great influence on the transmission pressure angle, instantaneous contact ratio, and transmission error of the elliptic gear, and the eccentricity error has a significant influence on the transmission error. In order to ensure the normal meshing condition of the elliptic gear, the eccentricity should be less than 0.7071, and the maximum instantaneous contact ratio is 1.809. The research results can provide some guidance for the following noncircular spur gear transmission test and transmission error research.

scholarly journals Optimization of Tooth Root Profile Using Bezier Curve with G2 Continuity to Reduce Bending Stress of Asymmetric Spur Gear Tooth

2018 ◽  
Vol 237 ◽  
pp. 03010 ◽  
Author(s):  
Priyakant Vaghela ◽  
Jagdish Prajapati
Keyword(s):  
Stress Concentration ◽  
Gear Tooth ◽  
Spur Gear ◽  
Bézier Curve ◽  
Bezier Curve ◽  
Tooth Root ◽  
Geometric Continuity ◽  
Bending Stress ◽  
Gear Design ◽  
G2 Continuity

This research describes simple and innovative approach to reduce bending stress at tooth root of asymmetric spur gear tooth which is desire for improve high load carrying capacity. In gear design at root of tooth circular-filleted is widely used. Blending of the involute profile of tooth and circular fillet creates discontinuity at root of tooth causes stress concentration occurs. In order to minimize stress concentration, geometric continuity of order 2 at the blending of gear tooth plays very important role. Bezier curve is used with geometric continuity of order 2 at tooth root of asymmetric spur gear to reduce bending stress.

Sign in / Sign up

Export Citation Format

Share Document