Compressibility and Variable Density Effects in Turbulent Boundary layers

2006 ◽  
Vol 129 (4) ◽  
pp. 441-448 ◽  
Author(s):  
Kunlun Liu ◽  
Richard H. Pletcher
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Wall Temperature ◽  
Stokes Equations ◽  
Variable Density ◽  
Turbulent Boundary Layers ◽  
Reynolds Analogy ◽  
Density Effects

Two compressible turbulent boundary layers have been calculated by using direct numerical simulation. One case is a subsonic turbulent boundary layer with constant wall temperature for which the wall temperature is 1.58 times the freestream temperature and the other is a supersonic adiabatic turbulent boundary layer subjected to a supersonic freestream with a Mach number 1.8. The purpose of this study is to test the strong Reynolds analogy (SRA), the Van Driest transformation, and the applicability of Morkovin’s hypothesis. For the first case, the influence of the variable density effects will be addressed. For the second case, the role of the density fluctuations, the turbulent Mach number, and dilatation on the compressibility will be investigated. The results show that the Van Driest transformation and the SRA are satisfied for both of the flows. Use of local properties enable the statistical curves to collapse toward the corresponding incompressible curves. These facts reveal that both the compressibility and variable density effects satisfy the similarity laws. A study about the differences between the compressibility effects and the variable density effects associated with heat transfer is performed. In addition, the difference between the Favre average and Reynolds average is measured, and the SGS terms of the Favre-filtered Navier-Stokes equations are calculated and analyzed.

Investigation of Flat-Plate Hypersonic, Turbulent Boundary Layers With Heat Transfer

1961 ◽  
Vol 28 (3) ◽  
pp. 323-329 ◽  
Author(s):  
Eva M. Winkler
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Friction Coefficient ◽  
Mach Number ◽  
Flat Plate ◽  
Skin Friction ◽  
Boundary Layers ◽  
Skin Friction Coefficient ◽  
Turbulent Boundary Layers ◽  
Reynolds Analogy

Naturally turbulent boundary layers on a cooled flat plate have been investigated at several distances from the leading edge of the plate at a Mach number of 5.2 for three rates of steady-state heat transfer to the surface. Measurements of Pitot and static pressures and of total and wall temperatures made it possible to compute velocity profiles, static-temperature profiles, and boundary-layer parameters without resorting to assumptions. The data demonstrate that the Reynolds analogy between skin friction and heat transfer is valid for all conditions of the present experiments. With increasing rate of heat transfer to the surface, the skin-friction coefficient was found to decrease, a phenomenon opposite to that predicted by theories and empirical relations. On the basis of the present data and other published results of compressible and incompressible turbulent boundary-layer skin friction, a simple relation was devised which describes closely the variation of the skin-friction coefficient with Mach number, heat-transfer rate, and momentum-thickness Reynolds number.

scholarly journals Direct Numerical Simulation on Mach Number and Wall Temperature Effects in the Turbulent Flows of Flat-Plate Boundary Layer

2014 ◽  
Vol 17 (1) ◽  
pp. 189-212 ◽  
Author(s):  
Xian Liang ◽  
Xinliang Li
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Mach Number ◽  
Turbulent Boundary Layer ◽  
Direct Numerical Simulation ◽  
Flat Plate ◽  
Wall Temperature ◽  
Wall Region ◽  
Mean Velocity ◽  
Reynolds Analogy

AbstractIn this paper, direct numerical simulation (DNS) is presented for spatially evolving turbulent boundary layer over an isothermal flat-plate atMa∞= 2.25,5,6,8. WhenMa∞= 8, two cases with the ratio of wall-to-reference temperatureTω/T∞= 1.9 and 10.03 are considered respectively. The wall temperature approaches recovery temperatures for other cases. The characteristics of compressible turbulent boundary layer (CTBL) affected by freestream Mach number and wall temperature are investigated. It focuses on assessing compressibility effects and the validity of Morkovin's hypothesis through computing and analyzing the mean velocity profile, turbulent intensity, the strong Reynolds analogy (SRA) and possibility density function of dilatation term. The results show that, when the wall temperature approaches recovery temperature, the effects of Mach number on compressibility is insignificant. As a result, the compressibility effect is very weak and the Morkovin's hypothesis is still valid for Mach number even up to 8. However, when Mach number equal to 8, the wall temperature effect on the compressibility is sensitive. In this case, whenTω/T∞= 1.9, the Morkovin's hypothesis is not fully valid. The validity of classical SRA depends on wall temperature directly. A new modified SRA is proposed to eliminate such negative factor in near wall region. Finally the effects of Mach number and wall temperature on streaks are also studied.

Prediction of Turbulent Boundary Layer Development in Conical Diffusers

1966 ◽  
Vol 8 (4) ◽  
pp. 426-436 ◽  
Author(s):  
A. D. Carmichael ◽  
G. N. Pustintsev
Keyword(s):  
Boundary Layer ◽  
Kinetic Energy ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Shape Factor ◽  
Turbulent Boundary Layers ◽  
Energy Deficit ◽  
Momentum Thickness ◽  
Boundary Layer Development ◽  
Layer Development

Methods of predicting the growth of turbulent boundary layers in conical diffusers using the kinetic-energy deficit equation were developed. Three different forms of auxiliary equations were used. Comparison between the measured and predicted results showed that there was fair agreement although there was a tendency to underestimate the predicted momentum thickness and over-estimate the predicted shape factor.

scholarly journals Self-similar compressible turbulent boundary layers with pressure gradients. Part 1. Direct numerical simulation and assessment of Morkovin’s hypothesis

2019 ◽  
Vol 880 ◽  
pp. 239-283 ◽  
Author(s):  
Christoph Wenzel ◽  
Tobias Gibis ◽  
Markus Kloker ◽  
Ulrich Rist
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Mach Number ◽  
Direct Numerical Simulation ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Shear Stresses ◽  
Pressure Gradients ◽  
Mean Flow ◽  
Self Similar

A direct numerical simulation study of self-similar compressible flat-plate turbulent boundary layers (TBLs) with pressure gradients (PGs) has been performed for inflow Mach numbers of 0.5 and 2.0. All cases are computed with smooth PGs for both favourable and adverse PG distributions (FPG, APG) and thus are akin to experiments using a reflected-wave set-up. The equilibrium character allows for a systematic comparison between sub- and supersonic cases, enabling the isolation of pure PG effects from Mach-number effects and thus an investigation of the validity of common compressibility transformations for compressible PG TBLs. It turned out that the kinematic Rotta–Clauser parameter $\unicode[STIX]{x1D6FD}_{K}$ calculated using the incompressible form of the boundary-layer displacement thickness as length scale is the appropriate similarity parameter to compare both sub- and supersonic cases. Whereas the subsonic APG cases show trends known from incompressible flow, the interpretation of the supersonic PG cases is intricate. Both sub- and supersonic regions exist in the boundary layer, which counteract in their spatial evolution. The boundary-layer thickness $\unicode[STIX]{x1D6FF}_{99}$ and the skin-friction coefficient $c_{f}$, for instance, are therefore in a comparable range for all compressible APG cases. The evaluation of local non-dimensionalized total and turbulent shear stresses shows an almost identical behaviour for both sub- and supersonic cases characterized by similar $\unicode[STIX]{x1D6FD}_{K}$, which indicates the (approximate) validity of Morkovin’s scaling/hypothesis also for compressible PG TBLs. Likewise, the local non-dimensionalized distributions of the mean-flow pressure and the pressure fluctuations are virtually invariant to the local Mach number for same $\unicode[STIX]{x1D6FD}_{K}$-cases. In the inner layer, the van Driest transformation collapses compressible mean-flow data of the streamwise velocity component well into their nearly incompressible counterparts with the same $\unicode[STIX]{x1D6FD}_{K}$. However, noticeable differences can be observed in the wake region of the velocity profiles, depending on the strength of the PG. For both sub- and supersonic cases the recovery factor was found to be significantly decreased by APGs and increased by FPGs, but also to remain virtually constant in regions of approximated equilibrium.

Velocity Profiles of Turbulent Boundary Layers

1969 ◽  
Vol 73 (698) ◽  
pp. 143-147 ◽  
Author(s):  
M. K. Bull
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Velocity Profile ◽  
Boundary Layers ◽  
Experimental Work ◽  
Constant Pressure ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Boundary Layer Equations

Although a numerical solution of the turbulent boundary-layer equations has been achieved by Mellor and Gibson for equilibrium layers, there are many occasions on which it is desirable to have closed-form expressions representing the velocity profile. Probably the best known and most widely used representation of both equilibrium and non-equilibrium layers is that of Coles. However, when velocity profiles are examined in detail it becomes apparent that considerable care is necessary in applying Coles's formulation, and it seems to be worthwhile to draw attention to some of the errors and inconsistencies which may arise if care is not exercised. This will be done mainly by the consideration of experimental data. In the work on constant pressure layers, emphasis tends to fall heavily on the author's own data previously reported in ref. 1, because the details of the measurements are readily available; other experimental work is introduced where the required values can be obtained easily from the published papers.

Equilibrium-Turbulent Boundary Layer Prediction for a Proposed Prandtl Mixing Length Distribution

1968 ◽  
Vol 10 (5) ◽  
pp. 426-433 ◽  
Author(s):  
F. C. Lockwood
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Length Distribution ◽  
Momentum Equation ◽  
Turbulent Boundary Layers ◽  
Mixing Length ◽  
Good Agreement

The momentum equation is solved numerically for a suggested ramp variation of the Prandtl mixing length across an equilibrium-turbulent boundary layer. The predictions of several important boundary-layer functions are compared with the equilibrium experimental data. Comparisons are also made with some recent universal recommendations for turbulent boundary layers since the equilibrium experimental data are limited. Good agreement is found between the predictions, the experimental data, and the recommendations.

A Simplified Form of the Auxiliary Equation for Use in the Calculation of Turbulent Boundary Layers

1958 ◽  
Vol 62 (567) ◽  
pp. 215-219
Author(s):  
T. J. Black
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Auxiliary Equation ◽  
Pressure Gradients ◽  
Momentum Thickness ◽  
Form Parameter ◽  
New Type ◽  
Simple Quadrature

A New type of auxiliary equation is given for calculating the development of the form-parameter H in turbulent boundary layers with adverse pressure gradients. The chief advantage of this new method lies in the rapidity and ease of calculation which has been achieved, without apparent sacrifice of accuracy.Whereas the growth of momentum thickness in the turbulent boundary layer can now be rapidly calculated by methods involving only simple quadrature, the prediction of the form parameter development remains a laborious task, while the results obtained do not always appear to justify the complexity of the calculations.

On the scaling in sink-flow turbulent boundary layers

2013 ◽  
Vol 737 ◽  
pp. 329-348 ◽  
Author(s):  
Shivsai Ajit Dixit ◽  
O. N. Ramesh
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Physical Space ◽  
Streamwise Velocity ◽  
Turbulent Boundary Layers ◽  
Velocity Spectrum ◽  
Scaling Exponent ◽  
Order Of Magnitude

AbstractScaling of the streamwise velocity spectrum ${\phi }_{11} ({k}_{1} )$ in the so-called sink-flow turbulent boundary layer is investigated in this work. The present experiments show strong evidence for the ${ k}_{1}^{- 1} $ scaling i.e. ${\phi }_{11} ({k}_{1} )= {A}_{1} { U}_{\tau }^{2} { k}_{1}^{- 1} $, where ${k}_{1} $ is the streamwise wavenumber and ${U}_{\tau } $ is the friction velocity. Interestingly, this ${ k}_{1}^{- 1} $ scaling is observed much farther from the wall and at much lower flow Reynolds number (both differing by almost an order of magnitude) than what the expectations from experiments on a zero-pressure-gradient turbulent boundary layer flow would suggest. Furthermore, the coefficient ${A}_{1} $ in the present sink-flow data is seen to be non-universal, i.e. ${A}_{1} $ varies with height from the wall; the scaling exponent −1 remains universal. Logarithmic variation of the so-called longitudinal structure function, which is the physical-space counterpart of spectral ${ k}_{1}^{- 1} $ scaling, is also seen to be non-universal, consistent with the non-universality of ${A}_{1} $. These observations are to be contrasted with the universal value of ${A}_{1} $ (along with the universal scaling exponent of −1) reported in the literature on zero-pressure-gradient turbulent boundary layers. Theoretical arguments based on dimensional analysis indicate that the presence of a streamwise pressure gradient in sink-flow turbulent boundary layers makes the coefficient ${A}_{1} $ non-universal while leaving the scaling exponent −1 unaffected. This effect of the pressure gradient on the streamwise spectra, as discussed in the present study (experiments as well as theory), is consistent with other recent studies in the literature that are focused on the structural aspects of turbulent boundary layer flows in pressure gradients (Harun et al., J. Fluid Mech., vol. 715, 2013, pp. 477–498); the present paper establishes the link between these two. The variability of ${A}_{1} $ accommodated in the present framework serves to clarify the ideas of universality of the ${ k}_{1}^{- 1} $ scaling.

Velocity and Temperature Profiles in Turbulent Boundary Layers With Tangential Injection

1962 ◽  
Vol 84 (1) ◽  
pp. 45-54 ◽  
Author(s):  
R. A. Seban ◽  
L. H. Back
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Thermal Behavior ◽  
Boundary Layers ◽  
Film Cooling ◽  
Mass Velocity ◽  
Free Stream ◽  
Turbulent Boundary Layers ◽  
Temperature Profiles ◽  
Adiabatic Wall

Velocity and temperature profiles are presented for the turbulent boundary layer downstream of a tangential injection slot for the further clarification of the film-cooling problem. The profiles refer primarily to an injection mass velocity of 0.36 times that of the free stream; these and other auxiliary results demonstrate a complex hydrodynamic and relatively simple thermal behavior in which the temperature profiles appear to be similar in all cases. By using this correspondence together with the approximation of a fully developed hydrodynamic layer in most of the downstream region, it is possible to rationalize the adiabatic wall temperatures that have been presented previously.

Sign in / Sign up

Export Citation Format

Share Document