An Integrated Approach for Friction Damper Design

1990 ◽  
Vol 112 (2) ◽  
pp. 175-182 ◽  
Author(s):  
T. M. Cameron ◽  
J. H. Griffin ◽  
R. E. Kielb ◽  
T. M. Hoosac
Keyword(s):  
Optimal Design ◽  
High Speed ◽  
Design Procedure ◽  
Single Mode ◽  
Design Parameters ◽  
Bench Test ◽  
Friction Damper ◽  
Friction Dampers ◽  
Damper Design ◽  
Blade Model

A procedure is outlined for determining the optimal design of friction dampers for high-speed turbomachinery blading. The procedure includes: An integration of bench test results with finite-element analysis and a single-mode blade model to ensure accuracy of the analytical model and improve reliability of the friction damper design; an extension of the single-mode blade model to predict the engine behavior of friction dampers; and a new way of viewing analytical and experimental results in terms of a damper performance curve to determine optimal design parameters, when the levels of excitation and damping in the system are unknown. Unique experiments are performed on a test disk in order to demonstrate and verify the accuracy of the design procedure.

The Engagement of Hybrid Ultra High Space Division Multiplexing with Maximum Time Division Multiplexing Techniques for High-Speed Single-Mode Fiber Cable Systems

2019 ◽  
Vol 0 (0) ◽  
Author(s):  
I. S. Amiri ◽  
P. G. Kuppusamy ◽  
Ahmed Nabih Zaki Rashed ◽  
P. Jayarajan ◽  
M. R. Thiyagupriyadharsan ◽  
...  
Keyword(s):  
Communication Systems ◽  
High Speed ◽  
Single Mode ◽  
Single Mode Fiber ◽  
Design Parameters ◽  
Control Parameters ◽  
Data Rates ◽  
Fiber Optic Communication ◽  
High Space ◽  
Optic Communication

AbstractHigh-speed single-mode fiber-optic communication systems have been presented based on various hybrid multiplexing schemes. Refractive index step and silica-doped germanium percentage parameters are also preserved during their technological boundaries of attention. It is noticed that the connect design parameters suffer more nonlinearity with the number of connects. Two different propagation techniques have been used to investigate the transmitted data rates as a criterion to enhance system performance. The first technique is soliton propagation, where the control parameters lead to equilibrium between the pulse spreading due to dispersion and the pulse shrinking because of nonlinearity. The second technique is the MTDM technique where the parameters are adjusted to lead to minimum dispersion. Two cases are investigated: no dispersion cancellation and dispersion cancellation. The investigations are conducted over an enormous range of the set of control parameters. Thermal effects are considered through three basic quantities, namely the transmission data rates, the dispersion characteristics, and the spectral losses.

scholarly journals A Two-Round Optimization Design Method for Aerostatic Spindles Considering the Fluid–Structure Interaction Effect

2021 ◽  
Vol 11 (7) ◽  
pp. 3017
Author(s):  
Qiang Gao ◽  
Siyu Gao ◽  
Lihua Lu ◽  
Min Zhu ◽  
Feihu Zhang
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Design Method ◽  
Fluid Structure Interaction ◽  
Design Procedure ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Aerostatic Spindle

The fluid–structure interaction (FSI) effect has a significant impact on the static and dynamic performance of aerostatic spindles, which should be fully considered when developing a new product. To enhance the overall performance of aerostatic spindles, a two-round optimization design method for aerostatic spindles considering the FSI effect is proposed in this article. An aerostatic spindle is optimized to elaborate the design procedure of the proposed method. In the first-round design, the geometrical parameters of the aerostatic bearing were optimized to improve its stiffness. Then, the key structural dimension of the aerostatic spindle is optimized in the second-round design to improve the natural frequency of the spindle. Finally, optimal design parameters are acquired and experimentally verified. This research guides the optimal design of aerostatic spindles considering the FSI effect.

Momentum exchange impact damper design methodology for object-wall-collision problems

2017 ◽  
Vol 24 (14) ◽  
pp. 3206-3218
Author(s):  
Yohei Kushida ◽  
Hiroaki Umehara ◽  
Susumu Hara ◽  
Keisuke Yamada
Keyword(s):  
Optimal Design ◽  
Design Methodology ◽  
Design Parameters ◽  
Momentum Exchange ◽  
Impact Damper ◽  
One Dimensional ◽  
Practical Design ◽  
Wall Collision ◽  
Damper Design ◽  
And Control

Momentum exchange impact dampers (MEIDs) were proposed to control the shock responses of mechanical structures. They were applied to reduce floor shock vibrations and control lunar/planetary exploration spacecraft landings. MEIDs are required to control an object’s velocity and displacement, especially for applications involving spacecraft landing. Previous studies verified numerous MEID performances through various types of simulations and experiments. However, previous studies discussing the optimal design methodology for MEIDs are limited. This study explicitly derived the optimal design parameters of MEIDs, which control the controlled object’s displacement and velocity to zero in one-dimensional motion. In addition, the study derived sub-optimal design parameters to control the controlled object’s velocity within a reasonable approximation to derive a practical design methodology for MEIDs. The derived sub-optimal design methodology could also be applied to MEIDs in two-dimensional motion. Furthermore, simulations conducted in the study verified the performances of MEIDs with optimal/sub-optimal design parameters.

Development of High-Speed Response Electromagnetic Linear Actuator Using for Pneumatic Control Valve

2014 ◽  
Vol 532 ◽  
pp. 41-45 ◽  
Author(s):  
Myung Jin Chung
Keyword(s):  
Optimal Design ◽  
Dynamic Characteristics ◽  
High Speed ◽  
Design Method ◽  
Control Valve ◽  
Design Parameters ◽  
Linear Actuator ◽  
Analytic Model ◽  
Electromagnetic Linear Actuator ◽  
Quadratic Programming Method

Analytic model of electromagnetic linear actuator in the function of electric and geometric parameters is proposed and the effects of the design parameters on the dynamic characteristics are analyzed. To improve the dynamic characteristics, optimal design is conducted by applying sequential quadratic programming method to the analytic model. This optimal design method aims to minimize the response time and maximize force efficiency. By this procedure, electromagnetic linear actuator having high-speed characteristics is developed.

Development and Application of a Multi-Disciplinary Multi-Regime Design Methodology of a Low-Noise Contra-Rotating Open-Rotor

2015 ◽  
Author(s):  
Michaël Leborgne ◽  
Timothée Lonfils ◽  
Ingrid Lepot
Keyword(s):  
Noise Reduction ◽  
High Speed ◽  
Design Methodology ◽  
Design Procedure ◽  
Low Noise ◽  
Design Parameters ◽  
Mechanical Constraints ◽  
Open Rotor ◽  
Mechanical Optimization ◽  
Lifting Line

This paper focuses on the development and exploitation of a multi-disciplinary, optimization-assisted, design methodology for contra-rotating open-rotors. The design procedure relies on a two-step approach. An aero-mechanical optimization is first performed to generate a geometry with good performances over several high-speed points representative of a mission. This geometry is subsequently used as the baseline of an aero-mechanical-acoustic optimization focusing on interaction noise reduction at Cutback and Sideline low-speed points. In terms of design parameters, both rotors are modified for the first phase but only the upper part of the front rotor is altered for the noise minimization. A fully-automatic high-fidelity aero-mechanical-acoustic computational chain with fluid-structure coupling is exploited in combination with evolutionary algorithms assisted by surrogate models for the constrained-optimization process. The acoustic footprint is estimated by a simplified but fast and relevant formulation combining an unsteady lifting-line and an acoustic propagation method. The best geometry of the first design gains 1.2pt in weighted efficiency while respecting all the aero-mechanical constraints. The acoustic optimization shows that noise reduction at Sideline and Cutback points is strongly antagonistic. However, significant Sideline noise reduction from 3.5 to 5.5dB depending on the harmonics is achieved while maintaining Cutback noise and without major degradation of high-speed efficiency.

Identification of key design parameters of high-speed train for optimal design

2014 ◽  
Vol 73 (1-4) ◽  
pp. 251-265 ◽  
Author(s):  
J. Zhang ◽  
G. F. Ding ◽  
Y. S. Zhou ◽  
J. Jiang ◽  
X. Ying ◽  
...  
Keyword(s):  
Optimal Design ◽  
High Speed ◽  
Design Parameters ◽  
High Speed Train

Seismic retrofit of structures using rotational friction dampers with restoring force

2020 ◽  
Vol 23 (16) ◽  
pp. 3525-3540
Author(s):  
Asad Naeem ◽  
Jinkoo Kim
Keyword(s):  
Ground Motions ◽  
Design Procedure ◽  
Steel Structures ◽  
Friction Damper ◽  
Heavy Duty ◽  
Limit States ◽  
Restoring Force ◽  
Friction Dampers ◽  
Torsional Spring ◽  
Capacity Spectrum

In this study, the seismic performance of a rotational friction damper with restoring force is presented. The torsional spring friction damper consists of rotational friction pads with the heavy duty torsional springs attached on both sides of the friction damper. An analytical model and a design procedure for the damper are developed using capacity spectrum method. A parametric study is carried out to investigate the influence of the torsional spring in the response of the structure when subjected to ground motions. The seismic performances of steel structures retrofitted with the torsional spring friction damper and conventional rotational friction dampers are evaluated using fragility analysis, which shows that the structure retrofitted with the torsional spring friction damper has the smallest probability of reaching the specific limit states.

scholarly journals A Simulation Study for the Design of Membrane Restrictor in an Opposed-Pad Hydrostatic Bearing to Achieve High Static Stiffness

Lubricants ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 71
Author(s):  
Ta-Hua Lai ◽  
Shih-Chieh Lin
Keyword(s):  
Optimal Design ◽  
Design Procedure ◽  
Effective Area ◽  
Design Parameters ◽  
Static Stiffness ◽  
Load Range ◽  
Hydrostatic Bearing ◽  
Optimal Value ◽  
Bearing Stiffness ◽  
Design Restriction

The effects of a membrane restrictor’s design parameters on the performance of a hydrostatic opposed-pad bearing are presented in this article. Compared to the single-pad bearing, the opposed-pad bearing can perform much better in terms of static stiffness over a wider load range. It is also found that, for small bearing eccentricity, the optimal design restriction ratio of 0.25 still results in high bearing stiffness even if the dimensionless stiffness of membrane is not the optimal value of 1.33. Furthermore, decreasing the ratio of the upper effective area to the lower effective area generally increases the applicable working range of the bearing. Additionally, for high loading demands, the chance for further improvement of bearing performance by employing different design parameter for each pad is examined. Finally, a design procedure for designing the membrane restrictor for an opposed-pad bearing to achieve high static stiffness is given.

Optimal Design of a Parallel Micromanipulator for Precision Machining

2009 ◽  
Vol 69-70 ◽  
pp. 590-594
Author(s):  
Z.F. Wang ◽  
Guan Wang ◽  
Shi Ming Ji ◽  
J.H. Sun
Keyword(s):  
Optimal Design ◽  
Search Algorithm ◽  
Design Procedure ◽  
Pattern Search ◽  
Design Parameters ◽  
Precision Machining ◽  
Pattern Search Algorithm ◽  
Generalized Pattern Search ◽  
Precision And Accuracy ◽  
Design Result

A parallel micromanipulator (PmM) which can be applied into the precision machining is optimized in the paper. This paper adopts a methodology to determine a set of optimal design parameters of PmM whose workspace is as close as possible of being equal to a prescribed cuboid dexterous workspace (PCDW). The kinematic problem is analyzed in brief to determine the design parameters and their relation. Then, an optimal design procedure which adopts the generalized pattern search algorithm in the genetic algorithm and direct search toolbox of Matlab is proposed to solve these problems. As an applying example, the results of four cases PCDW to PmM are presented. And the design result is compared with a concept of the distance between the best state of the PmM and the requirement of the operation task. The method and result of this paper are very useful for the design of micromanipulator for the machining field which requires the high precision and accuracy.

Sign in / Sign up

Export Citation Format

Share Document