scholarly journals Spatially Resolved Streaming Potentials of Human Intervertebral Disk Motion Segments Under Dynamic Axial Compression

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
James C. Iatridis ◽  
Masaru Furukawa ◽  
Ian A. F. Stokes ◽  
Mack G. Gardner-Morse ◽  
Jeffrey P. Laible

Intervertebral disk degeneration results in alterations in the mechanical, chemical, and electrical properties of the disk tissue. The purpose of this study is to record spatially resolved streaming potential measurements across intervertebral disks exposed to cyclic compressive loading. We hypothesize that the streaming potential profile across the disk will vary with radial position and frequency and is proportional to applied load amplitude, according to the presumed fluid-solid relative velocity and measured glycosaminoglycan content. Needle electrodes were fabricated using a linear array of Ag∕AgCl micro-electrodes and inserted into human motion segments in the midline from anterior to posterior. They were connected to an amplifier to measure electrode potentials relative to the saline bath ground. Motion segments were loaded in axial compression under a preload of 500N, sinusoidal amplitudes of ±200N and ±400N, and frequencies of 0.01Hz, 0.1Hz, and 1Hz. Streaming potential data were normalized by applied force amplitude, and also compared with paired experimental measurements of glycosaminoglycans in each disk. Normalized streaming potentials varied significantly with sagittal position and there was a significant location difference at the different frequencies. Normalized streaming potential was largest in the central nucleus region at frequencies of 0.1Hz and 1.0Hz with values of approximately 3.5μV∕N. Under 0.01Hz loading, normalized streaming potential was largest in the outer annulus regions with a maximum value of 3.0μV∕N. Correlations between streaming potential and glycosaminoglycan content were significant, with R2 ranging from 0.5 to 0.8. Phasic relationships between applied force and electrical potential did not differ significantly by disk region or frequency, although the largest phase angles were observed at the outermost electrodes. Normalized streaming potentials were associated with glycosaminoglycan content, fluid, and ion transport. Results suggested that at higher frequencies the transport of water and ions in the central nucleus region may be larger, while at lower frequencies there is enhanced transport near the periphery of the annulus. This study provides data that will be helpful to validate multiphasic models of the disk.

2021 ◽  
Author(s):  
Damien Jougnot ◽  
Luong Duy Thanh ◽  
Mariangeles Soldi ◽  
Jan Vinogradov ◽  
Luis Guarracino

<p>Understanding streaming potential generation in porous media is of high interest for hydrological and reservoir studies as it allows to relate water fluxes to measurable electrical potential distributions in subsurface geological settings. The evolution of streaming potential <span>stems</span> from electrokinetic coupling between water and electrical fluxes due to the presence of an electrical double layer at the interface between the mineral and the pore water. Two different approaches can be used to model and interpret the generation of the streaming potential in porous media: the classical coupling coefficient approach based on the Helmholtz-Smoluchowski equation, and the effective excess charge density. Recent studies based on both approaches use a mathematical up-scaling procedure that employs the so-called fractal theory. In these studies, the porous medium is represented by a bundle of tortuous capillaries characterized by a fractal capillary-size distribution law. The electrokinetic coupling between the fluid flow and electric current is obtained by averaging the processes that take place in a single capillary. In most cases, closed-form expressions for the electrokinetic parameters are obtained in terms of macroscopic hydraulic variables like permeability, saturation and porosity. In this presentation we propose a review of the existing fractal distribution models that predict the streaming potential in porous media and discuss their benefits compared against other published models.</p>


2021 ◽  
Vol 13 (1) ◽  
pp. 91-100
Author(s):  
Philip Poillot ◽  
Christine L. Le Maitre ◽  
Jacques M. Huyghe

AbstractThe strain-generated potential (SGP) is a well-established mechanism in cartilaginous tissues whereby mechanical forces generate electrical potentials. In articular cartilage (AC) and the intervertebral disc (IVD), studies on the SGP have focused on fluid- and ionic-driven effects, namely Donnan, diffusion and streaming potentials. However, recent evidence has indicated a direct coupling between strain and electrical potential. Piezoelectricity is one such mechanism whereby deformation of most biological structures, like collagen, can directly generate an electrical potential. In this review, the SGP in AC and the IVD will be revisited in light of piezoelectricity and mechanotransduction. While the evidence base for physiologically significant piezoelectric responses in tissue is lacking, difficulties in quantifying the physiological response and imperfect measurement techniques may have underestimated the property. Hindering our understanding of the SGP further, numerical models to-date have negated ferroelectric effects in the SGP and have utilised classic Donnan theory that, as evidence argues, may be oversimplified. Moreover, changes in the SGP with degeneration due to an altered extracellular matrix (ECM) indicate that the significance of ionic-driven mechanisms may diminish relative to the piezoelectric response. The SGP, and these mechanisms behind it, are finally discussed in relation to the cell response.


1981 ◽  
Vol 103 (4) ◽  
pp. 280-292 ◽  
Author(s):  
R. C. Lee ◽  
E. H. Frank ◽  
A. J. Grodzinsky ◽  
D. K. Roylance

The compressive stiffness of articular cartilage was examined in oscillatory confined compression over a wide frequency range including high frequencies relevant to impact loading. Nonlinear behavior was found when the imposed sinusoidal compression amplitude exceeded a threshold value that depended on frequency. Linear behavior was attained only by suitable control of the compression amplitude. This was enabled by real time Fourier analysis of data which provided an accurate assessment of the extent of nonlinearity. For linear viscoelastic behavior, a stiffness could be defined in the usual sense. The dependence of the stiffness on ionic strength and proteoglycan content showed that electrostatic forces between matrix charge groups contribute significantly to cartilage’s compressive stiffness over the 0.001 to 20 Hz frequency range. Sinusoidal streaming potentials were also generated by oscillatory compression. A theory relating the streaming potential field to the fluid velocity field is derived and used to interpret the data. The observed magnitude of the streaming potential suggests that interstitial fluid flow is significant to cartilage behavior over the entire frequency range. The use of simultaneous streaming potential and stiffness data with an appropriate theory appears to be an important tool for assessing the relative contribution of fluid flow, intrinsic matrix viscoelasticity, or other molecular mechanisms to energy dissipation in cartilage. This method is applicable in general to hydrated, charged polymers.


1931 ◽  
Vol 14 (5) ◽  
pp. 563-573 ◽  
Author(s):  
H. A. Abramson ◽  
E. B. Grossman

1. The conditions are described which are necessary for the comparison of certain types of electrokinetic potentials. An experimental comparison is made of (a) electrophoresis of quartz particles covered with egg albumin; and (b) similar experiments by Briggs on streaming potentials. A slight, consistent, difference is found between the electrophoretic potential and the streaming potential. This difference is probably due to the difference in the protein preparations used rather than to real difference in the electrophoretic and streaming potentials. 2. Data are given which facilitate the measurements and enhance the precision of the estimation of electrical mobilities of microscopic particles.


1969 ◽  
Vol 172 (1028) ◽  
pp. 203-225 ◽  

A rapid procedure based on that of Smyth & Wright (1966) is described for obtaining a measure of the permeability of rabbit gall-bladder epithelium to non-electrolytes. The underlying principles are that concentration gradients of permeant molecules produce lower rates of osmotic flow across a membrane than does the same gradient of an impermeant molecule, and that streaming potentials in the gall-bladder are directly proportional to the flow rate. Hence reflexion coefficients (cr’s) were calculated as the ratio of the streaming potential produced by a 0* 1 m gradient of the test solute to the streaming potential produced by a 0T m gradient of an impermeant reference solute, sucrose. The method yields results in agreement with those obtained in the gall-bladder by a zero-flow procedure. In general, the patterns of permeation derived are similar to those obtained in other tissues by the same procedure, by other osmotic procedures, or by direct chemical or tracer methods. The advantages of the method are that (a) large numbers of cr’s can be determined in one experiment with an average standard deviation of ± 8 % ; and (b) the minimum elapsed time between the preparation of a solution and the determination of or is about 90 s, so that cr’s may be obtained for some non-electrolytes subject to gradual chemical transformation in aqueous solution, such as aldehydes. The principles underlying osmotic methods of measuring permeability, and the effects of unstirred layers, are discussed.


Minerals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 306 ◽  
Author(s):  
Francisca San Martín ◽  
Claudio Aguilar

In the present work, the streaming potential of A. ferrooxidans and pyrite was measured in two environments: fresh and saline water (water with 35 g/L of NaCl) at different pH values. Also, attachment kinetics of A. ferrooxidans to pyrite was studied in fresh and saline water at pH 4. The results show that A. ferrooxidans and pyrite had lower streaming potentials (comparing absolute values) in saline water than in fresh water, indicating the compression in the electrical double layer caused by Cl− and Na+ ions. It was also determined that the bacteria had a higher level of attachment to pyrite in fresh water than in saline water. The high ionic strength of saline water reduced the attractive force between A. ferrooxidans and pyrite, which in turn reduced bacterial attachment. Electrostatic interactions were determined to be mainly repulsive, since the bacteria and mineral had the same charge at pH 4. Despite this, the bacteria adhered to pyrite, indicating that hydrophobic attraction forces and Lifshitz–van der Waals interactions were stronger than electrostatic interactions, which caused the adhesion of A. ferrooxidans to pyrite.


1963 ◽  
Vol 18 (6) ◽  
pp. 1263-1264 ◽  
Author(s):  
R. E. Beck ◽  
V. Mirkovitch ◽  
P. G. Andrus ◽  
R. I. Leininger

A system was developed to measure the streaming potential generated between the ends of a capillary by the flow of a fluid through the capillary. Zeta potential can be calculated from the streaming potential. Adequate sensitivity and reproducibility were achieved by making special electrodes: silver wires plated in KCl solution and embedded in agar, careful electrical shielding, and provision for reversal of flow through the capillary to minimize electrode errors. The apparatus was developed to measure streaming potentials generated by either RingerS's solution or blood in contact with capillaries made of different materials such as quartz, polyethylene, etc. An example of a determination using a quartz capillary is presented. interfaces; blood; salt solutions; glass; quartz Submitted on February 25, 1963


2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Yuina Abe ◽  
Hajime Konno ◽  
Shotaro Yoshida ◽  
Matsuhiko Nishizawa

The electrical response of the skin to mechanical stretches is reported here. The electrical potential difference across the epidermis, i.e., transepidermal potential (TEP) of porcine skin samples subjected to cyclic stretching, was measured in real time to observe electrochemical change in epidermal tissue. In addition to a conventional method of TEP measurement for the whole of skin sample, a probe-type system with a fine-needle salt bridge was used for direct measurement of TEP at a targeted local point of the skin. TEP decreased with the increased mechanical stretches, and the change of TEP was found to be mostly occurred in the epidermis but not dermis nor hypodermis by comparing the results of conventional and the probe-type methods. The observed change of TEP value was quick, reversible, and strain-dependent. Considering from such characteristic behaviors, one of the possible mechanisms of the modulation of TEP would be influence of the streaming potential caused by the fluid flow during the physical deformation of the epidermis.


1967 ◽  
Vol 7 (04) ◽  
pp. 359-368 ◽  
Author(s):  
S.H. Raza ◽  
S.S. Marsden

Abstract An experimental study of the flow of fine-textured, aqueous foams through Pyrex tubes is described. The foams range in quality F (ratio of gas volume to total volume) from 0.70 to 0.96 and behave like pseudoplastic fluids. At lower flow rates they exhibit laminar flow and have apparent viscosities which increase with quality, and which cover a range of 15 cp to 255 poise for tubes of 0.25- to 1.50-mm radius ri. At higher flow rates a plug-like type of flow is developed, the extent of which increases with both and ri. When the same foams flow through either open or packed Pyrex tubes, remarkably high streaming potentials phi E are often generated. These can easily reach 50v if nonionic foaming agents are used, but are at least an order of magnitude less for ionic foaming agents. A linear relationship between phi E and the pressure differential phi p is observed; this usually extrapolates to positive values of phi p at phi E of zero. The slope of the line increases with both F and ri. An equation was derived to describe the streaming potential of non-Newtonian fluids in circular tubes and was used to correlate experimental results. The calculated potential is are of the right order of magnitude. Introduction Foams are both unusual and intriguing in their physical properties, and have been the subject of many scientific studies. However, present knowledge of foams is still fragmentary, specific and often contradictory. Apparent viscosity of foam is the physical property of greatest interest to both rheologists and engineers. Sibree reported that the apparent viscosity decreased with increasing shear rate in a manner similar to some non-Newtonian fluids. Penny and Blackman reported that fire-fighting foams had both a limiting shear stress and a tensile yield stress. There is little doubt that some foams at least behave like non-Newtonian fluids, and have apparent viscosities considerably higher than those of either constituent phase. The high apparent viscosity of foam with its concomitant effect on mobility ratio and sweep efficiency no doubt prompted several attempts by research groups to use foam as a displacing agent in porous media. Based on recent experience, most of these groups probably succeeded in completely blocking fluid flow in the porous media and then abandoned their efforts. Two groups apparently found the successful combination of experimental parameters at about the same time. Others have recently added to our knowledge-of foam flow in porous media and its use as a displacing agent. An experimental problem encountered by Fried was a transient blockage of foam flow in porous media when distilled water was used to prepare the foam-producing solution. Fried surmised that this was due to an electrokinetic effect and he eliminated it by using electrolytes in preparing foaming solutions. He also measured the streaming potential of a number of foams in capillary tubes which he found to be appreciably higher than those obtained when the constituent liquid flowed under comparable conditions. This paper presents results of a more comprehensive study of the streaming potential generated by aqueous foam flowing in both open and packed Pyrex tubes. It also adds to knowledge of the rheology of these foams as deduced from their flow behavior in open tubes. APPARATUS AND PROCEDURE A diagram of the apparatus used is shown in Fig. 1. Details of its construction, testing and use are described elsewhere. Careful selection of materials, extreme cleanliness and rather elaborate electrical insulation and shielding were necessary to obtain reproducible results (15 percent). Both streaming potential and streaming current were measured with an electrometer. The design of the foam generator developed for this work is novel (Fig. 2). SPEJ P. 359ˆ


Author(s):  
Edwar Romero ◽  
Michael R. Neuman ◽  
Robert O. Warrington

Energy harvesting from environmental sources such as motion, light, and temperature changes, has been demonstrated with commercially viable products (such as human-powered flashlights, solar-powered calculators, and thermal-powered wristwatches). Vibration or motion is an attractive environmental energy source due to its abundance and availability. A new electromagnetic energy harvester presented here is found to be capable for scavenging energy from human motion. The electrical power output of an inertial energy scavenger is proportional to the acceleration-squared-to-frequency (ASTF) and the quality (Q) factor. Human motion is associated with large ASTF values and low Q factors while machine vibrations are usually related with the opposite. Thus, passive energy harvesting from human activities could generate as much power as the one available from machine harvesters. The limit for such inertial generator is estimated to be on the order of 1mW/cm3. This paper reviews the energy harvesting limits, the energy generation from human activities, and the development of a new oscillating electromagnetic generator. This energy harvester is built with a permanent magnet (PM) ring with multiple poles and a gear-shaped planar coil. The PM ring has attached an eccentric proof mass for converting external movement into oscillations or rotations, these oscillations induce an electrical potential on the planar coil. As much as 3.45μW of power have been generated with a prototype at a frequency of 2.7Hz on a laboratory shaker and 2.35μW had been obtained when positioned laterally on the hip while walking.


Sign in / Sign up

Export Citation Format

Share Document