Performance Characteristics of Shrouded and Unshrouded Impellers of a Centrifugal Compressor

1985 ◽  
Vol 107 (2) ◽  
pp. 528-533 ◽  
Author(s):  
H. Harada
Keyword(s):  
Velocity Distribution ◽  
Centrifugal Compressor ◽  
Closed Loop ◽  
Unsteady Flows ◽  
Test Stand ◽  
Performance Characteristics ◽  
Working Fluid ◽  
Overall Performance ◽  
Hot Film

The overall performance of shrouded and unshrouded identical impellers of a centrifugal compressor were tested and compared. A closed loop test stand with Freon gas as the working fluid was employed for the experiments. The inlet and outlet velocity distributions of both impellers were measured using a three-hole cobra probe and a hot-film probe to determine the velocity distribution and unsteady flows due to wakes and inlet stall.

Performance Characteristics of Two- and Three-Dimensional Impellers in Centrifugal Compressors

1988 ◽  
Vol 110 (1) ◽  
pp. 110-114 ◽  
Author(s):  
H. Harada
Keyword(s):  
Centrifugal Compressor ◽  
Closed Loop ◽  
Three Dimensional ◽  
Test Stand ◽  
Performance Characteristics ◽  
Working Fluid ◽  
Angle Distribution ◽  
Blade Angle ◽  
Operating Range ◽  
Overall Performance

The overall performance of two- and three-dimensional impellers of a centrifugal compressor were tested and compared. A closed-loop test stand with Freon gas as the working fluid was employed for the experiments. The inlet and outlet velocity distributions of all impellers were measured using three-hole cobra probes. As a result, it has been revealed that three-dimensional impeller in terms of efficiency, head coefficient, and operating range. Further, it has also been clarified that the impeller slip factor is affected by blade angle distribution.

scholarly journals Performance Characteristics of Two- and Three-Dimensional Impellers in Centrifugal Compressors

1986 ◽  
Author(s):  
H. Harada
Keyword(s):  
Centrifugal Compressor ◽  
Closed Loop ◽  
Three Dimensional ◽  
Performance Characteristics ◽  
Working Fluid ◽  
Angle Distribution ◽  
Two Dimensional ◽  
Blade Angle ◽  
Operating Range ◽  
Overall Performance

The overall performance of two- and three-dimensional impellers of a centrifugal compressor were tested and compared. A closed loop test stand with Freon gas as working fluid was employed for the experiments. The inlet and outlet velocity distribtions of all impellers were measured using three hole cobra probes. As a result, it has been revealed that three-dimensional impellers are superior to two-dimensional one in terms of efficiency, head coefficient and operating range. Further, it has also been clarified that the impeller slip factor is affected by blade angle distribution.

scholarly journals Comparative Study of Unsteady Flows in a Transonic Centrifugal Compressor With Vaneless and Vaned Diffusers

2001 ◽  
Author(s):  
Michael M. Cui
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Power Laws ◽  
Working Fluid ◽  
Local Flow ◽  
Transonic Centrifugal Compressor ◽  
Compressor Performance ◽  
Overall Performance

To reduce vibration and noise level, the impeller and diffuser blade numbers inside an industrial compressor are typically chosen without common divisors. The shapes of volutes or collectors in these compressors are also not axis-symmetric. When impeller blades pass these asymmetric structures, the flow field in the compressor is time-dependent and three-dimensional. To obtain a fundamental physical understanding of these three-dimensional unsteady flow fields and assess their impact on the compressor performance, the flow field inside the compressors needs to be studied as a whole to include asymmetric and unsteady interaction between the compressor components. In current study, a unified three-dimensional numerical model was built for a transonic centrifugal compressor including impeller, diffusers, and volute. HFC 134a was used as the working fluid. The thermodynamic and transport properties of the refrigerant gas were modeled by the Martin-Hou equation of state and power laws, respectively. The three-dimensional unsteady flow field was simulated with a Navier-Stokes solver using the k-ε turbulent model. The overall performance parameters are obtained by integrating the field quantities. Both unsteady flow field and overall performance are analyzed comparatively for each component. The compressor was tested in a water chiller system instrumented to obtain both overall performance data and local flow field quantities. The experimental and numerical results agree well. The correlation between the overall compressor performance and local flow field quantities is defined. The methodology developed and data obtained in these studies can be applied to centrifugal compressor design and optimization.

Effect of Suction Elbow and Inlet Guide Vanes on Flow Field in a Centrifugal Compressor Stage

2002 ◽  
Author(s):  
Michael M. Cui
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Power Laws ◽  
Working Fluid ◽  
Guide Vanes ◽  
Design And Optimization ◽  
Inlet Guide Vanes ◽  
Compressor Design ◽  
Overall Performance

Suction elbows and inlet guide vanes (IGVs) are typical upstream components in front of first-stage impellers in centrifugal compressors. The three-dimensional distortion induced by elbows and IGVs affects the flow field behind the IGV housing. Since the flow field in front of the impeller is subsonic, the flow motion induced by the rotating impeller will interact with the elbow and IGVs as well. The flow field resulting from these interactions is three-dimensional. The nature of this flow field defines design requirements of upstream components and impact overall performance of the compressor. To understand the mechanism controlling the interactions of up-steam components and optimize the compressor design for better efficiency and reliability, a numerical simulation of the flow field inside the entire first stage of the compressor was conducted. The stage studied includes suction elbow, IGV housing with vanes, and first-stage impeller. HFC 134a was used as the working fluid. The thermodynamic and transport properties of the refrigerant gas were modeled by the Martin-Hou equation of state and power laws respectively. The three-dimensional flow field was simulated with a Navier-Stokes solver using the k-ε turbulence model. The overall performance parameters are obtained by integrating the field quantities. The force, torque, and arm of moment acting on the IGVs were then calculated. The results can be used to improve centrifugal compressor design to achieve higher efficiency and improve reliability. The methodology developed in the current study can be applied to centrifugal compressor design and optimization.

scholarly journals Comparative Study of Unsteady Flows in a Transonic Centrifugal Compressor with Vaneless and Vaned Diffusers

2005 ◽  
Vol 2005 (1) ◽  
pp. 90-103 ◽  
Author(s):  
Michael M. Cui
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Power Laws ◽  
Working Fluid ◽  
Local Flow ◽  
Transonic Centrifugal Compressor ◽  
Compressor Performance ◽  
Overall Performance

To reduce vibration and noise level, the impeller and diffuser blade numbers inside an industrial compressor are typically chosen without common divisors. The shapes of volutes or collectors in these compressors are also not axis-symmetric. When impeller blades pass these asymmetric structures, the flow field in the compressor is time-dependent and three-dimensional. To obtain a fundamental physical understanding of these three-dimensional unsteady flow fields and assess their impact on the compressor performance, the flow field inside the compressors needs to be studied as a whole to include asymmetric and unsteady interaction between the compressor components. In the current study, a unified three-dimensional numerical model was built for a transonic centrifugal compressor including impeller, diffusers, and volute. HFC 134a was used as the working fluid. The thermodynamic and transport properties of the refrigerant gas were modeled by the Martin-Hou equation of state and power laws, respectively. The three-dimensional unsteady flow field was simulated with a Navier-Stokes solver using thek−εturbulent model. The overall performance parameters are obtained by integrating the field quantities. Both the unsteady flow field and the overall performance are analyzed comparatively for each component. The compressor was tested in a water chiller system instrumented to obtain both the overall performance data and local flow-field quantities. The experimental and numerical results agree well. The correlation between the overall compressor performance and local flow-field quantities is defined. The methodology developed and data obtained in these studies can be applied to the centrifugal compressor design and optimization.

scholarly journals Modelling an unconventional closed-loop deep borehole heat exchanger (DBHE): sensitivity analysis on the Newberry volcanic setting

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Hannah R. Doran ◽  
Theo Renaud ◽  
Gioia Falcone ◽  
Lehua Pan ◽  
Patrick G. Verdin
Keyword(s):  
Sensitivity Analysis ◽  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Energy Flow ◽  
Closed Loop ◽  
Working Fluid ◽  
Valuable Insight ◽  
Deep Borehole

AbstractAlternative (unconventional) deep geothermal designs are needed to provide a secure and efficient geothermal energy supply. An in-depth sensitivity analysis was investigated considering a deep borehole closed-loop heat exchanger (DBHE) to overcome the current limitations of deep EGS. A T2Well/EOS1 model previously calibrated on an experimental DBHE in Hawaii was adapted to the current NWG 55-29 well at the Newberry volcano site in Central Oregon. A sensitivity analysis was carried out, including parameters such as the working fluid mass flow rate, the casing and cement thermal properties, and the wellbore radii dimensions. The results conclude the highest energy flow rate to be 1.5 MW, after an annulus radii increase and an imposed mass flow rate of 5 kg/s. At 3 kg/s, the DBHE yielded an energy flow rate a factor of 3.5 lower than the NWG 55-29 conventional design. Despite this loss, the sensitivity analysis allows an assessment of the key thermodynamics within the wellbore and provides a valuable insight into how heat is lost/gained throughout the system. This analysis was performed under the assumption of subcritical conditions, and could aid the development of unconventional designs within future EGS work like the Newberry Deep Drilling Project (NDDP). Requirements for further software development are briefly discussed, which would facilitate the modelling of unconventional geothermal wells in supercritical systems to support EGS projects that could extend to deeper depths.

The Effect of Inlet Distortion on the Performance Characteristics of a Centrifugal Compressor

1983 ◽  
Vol 105 (2) ◽  
pp. 223-230 ◽  
Author(s):  
I. Ariga ◽  
N. Kasai ◽  
S. Masuda ◽  
Y. Watanabe ◽  
I. Watanabe
Keyword(s):  
Centrifugal Compressor ◽  
Total Pressure ◽  
Performance Characteristics ◽  
Performance Tests ◽  
Velocity Measurements ◽  
Test Rig ◽  
Low Speed ◽  
Inlet Distortion ◽  
Surge Margin ◽  
The Given

The present paper concerns itself with the effects of total pressure (and thus velocity) distortion on performance characteristics and surge margin of centrifugal compressors. Both radial and circumferential distortions were investigated. The performance tests as well as the velocity measurements within the impeller passages were carried out with a low-speed compressor test rig with the inlet honeycomb as the distortion generators and compared with the case of “no distortion” as a datum. The results indicated that the inlet distortion exerted unfavorable influences on the efficiency and the surge margin of the given compressor, though the influence of the radial distortion was much stronger than that of the circumferential one. Various distortion indices were further examined in order to correlate the performance to the inlet distortion.

scholarly journals Computational Analysis of the Performance Characteristics of a Supercritical CO2 Centrifugal Compressor

Computation ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 54 ◽  
Author(s):  
Senthil Raman ◽  
Heuy Kim
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
National Laboratory ◽  
Sandia National Laboratory ◽  
Ideal Gas ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Performance Characteristics ◽  
Supercritical Regime ◽  
Vaned Diffuser

A centrifugal compressor working with supercritical CO 2 (S-CO 2 ) has several advantages over other supercritical and conventional compressors. S-CO 2 is as dense as the liquid CO 2 and becomes difficult to compress. Thus, during the operation, the S-CO 2 centrifugal compressor requires lesser compression work than the gaseous CO 2 . The performance of S-CO 2 compressors is highly varying with tip clearance and vanes in the diffuser. To improve the performance of the S-CO 2 centrifugal compressor, knowledge about the influence of individual components on the performance characteristics is necessary. This present study considers an S-CO 2 compressor designed with traditional engineering design tools based on ideal gas behaviour and tested by SANDIA national laboratory. Three-dimensional, steady, viscous flow through the S-CO 2 compressor was analysed with computational fluid dynamics solver based on the finite volume method. Navier-Stokes equations are solved with K- ω (SST) turbulence model at operating conditions in the supercritical regime. Performance of the impeller, the main component of the centrifugal compressor is compared with the impeller with vaneless diffuser and vaned diffuser configurations. The flow characteristics of the shrouded impeller are also studied to analyse the tip-leakage effect.

scholarly journals Numerical study of flow patterns and heat transfer in mini twisted oval tubes

2015 ◽  
Vol 26 (12) ◽  
pp. 1550140 ◽  
Author(s):  
Amin Ebrahimi ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Critical Role ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Working Fluid ◽  
Transfer Performance ◽  
Temperature Dependent ◽  
Overall Performance

Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and available experimental results, the performance of TOTs is compared to a smooth circular tube. The overall performance of TOTs is evaluated by investigating the thermal-hydraulic performance and the results are analyzed in terms of the field synergy principle and entropy generation. Enhanced heat transfer performance for TOTs is observed at the expense of a higher pressure drop. Additionally, the secondary flow generated by the tube-wall twist is concluded to play a critical role in the augmentation of convective heat transfer, and consequently, better heat transfer performance. It is also observed that the improvement of synergy between velocity and temperature gradient and lower irreversibility cause heat transfer enhancement for TOTs.

Sign in / Sign up

Export Citation Format

Share Document