scholarly journals Quasi-Harmonic Friction-Induced Vibration

1970 ◽  
Vol 92 (4) ◽  
pp. 550-556 ◽  
Author(s):  
C. A. Brockley ◽  
P. L. Ko
Keyword(s):  
Experimental Investigation ◽  
Friction Velocity ◽  
Velocity Curve ◽  
Harmonic Vibration ◽  
Dynamic Friction ◽  
Sliding Velocity ◽  
Friction Forces ◽  
Automatic Transmissions ◽  
Friction Induced Vibration

A theoretical and experimental investigation of quasi-harmonic friction-induced vibration is reported. The vibration is of near-sinusoidal form and is solely governed by dynamic friction forces. However, the friction-velocity curve must be of a particular shape for the vibration to occur. The amplitude of the quasi-harmonic vibration is shown to increase with sliding velocity until oscillation ceases at some upper velocity boundary. The introduction of suitable damping will quench the vibration entirely. The vibration can exist at high sliding velocities and as a consequence may influence the operation of automatic transmissions, brakes, and clutches.

Boundary and Mixed Friction in the Presence of Dynamic Normal Loads: Part I—System Model

1995 ◽  
Vol 117 (2) ◽  
pp. 255-260 ◽  
Author(s):  
Andreas A. Polycarpou ◽  
Andres Soom
Keyword(s):  
Important Variable ◽  
Friction Model ◽  
System Model ◽  
Dynamic Friction ◽  
Discrete Elements ◽  
Friction Forces ◽  
Contact Compliance ◽  
Stiffness Characteristics ◽  
Nonlinear Normal ◽  
Linearized Model

The instantaneous normal motion between bodies in a sliding contact is an important variable in determining dynamic friction under unsteady sliding conditions. In order to model friction under dynamic conditions, it is therefore necessary to combine a dynamic model of the sliding system with an accurate model of the friction process. In the present work, the nonlinear normal dynamics of a friction test apparatus are described by a linearized model at a particular steady loading and sliding condition in a mixed or boundary-lubricated regime. The geometry is a line contact. The Hertzian bulk contact compliance and film and asperity damping and stiffness characteristics are included as discrete elements. In Part I of the paper, a fifth-order model is developed for the normal dynamics of the system, using both the Eigensystem Realization Algorithm (ERA) and classical experimental modal analysis techniques. In Part II, this system model is combined with a friction model, developed independently, to describe dynamic friction forces under both harmonic and impulsive applied normal loads.

scholarly journals Impact-sliding wear response of 2.25Cr1Mo steel tubes: Experimental and semi-analytical method

Friction ◽  
2021 ◽  
Author(s):  
Meigui Yin ◽  
Chaise Thibaut ◽  
Liwen Wang ◽  
Daniel Nélias ◽  
Minhao Zhu ◽  
...  
Keyword(s):  
Sliding Wear ◽  
Power Plants ◽  
Mechanical Response ◽  
Wear Behavior ◽  
Wear Test ◽  
Steel Tube ◽  
Wear Depth ◽  
Sliding Velocity ◽  
Friction Forces ◽  
The Impact

AbstractThe impact-sliding wear behavior of steam generator tubes in nuclear power plants is complex owing to the dynamic nature of the mechanical response and self-induced tribological changes. In this study, the effects of impact and sliding velocity on the impact-sliding wear behavior of a 2.25Cr1Mo steel tube are investigated experimentally and numerically. In the experimental study, a wear test rig that can measure changes in the impact and friction forces as well as the compressive displacement over different wear cycles, both in real time, is designed. A semi-analytical model based on the Archard wear law and Hertz contact theory is used to predict wear. The results indicate that the impact dynamic effect by the impact velocity is more significant than that of the sliding velocity, and that both velocities affect the friction force and wear degree. The experimental results for the wear depth evolution agree well with the corresponding simulation predictions.

Stick-Slip Behaviour of Seals With Respect to Time Dependent Friction Forces

2004 ◽  
Author(s):  
Markus Lindner ◽  
Matthias Kro¨ger ◽  
Karl Popp ◽  
Manuel Gime´nez
Keyword(s):  
Stability Analysis ◽  
Time Dependent ◽  
Dynamic Friction ◽  
Slip Effect ◽  
Stick Slip ◽  
Friction Forces ◽  
Seal Design

In the present paper dynamic friction processes in seals are investigated. The undesired stick-slip effect of these components under real technical conditions is analyzed. Starting with the basics of stick-slip vibrations the development of an advanced seal design with improved properties is presented that prevents stick-slip. Finally, an optimization based on the extensive but simple stability analysis is shown by an expanded theory of stick-slip simulations.

scholarly journals Experimental investigation of a single-degree-of-freedom system with Coulomb friction

2020 ◽  
Vol 99 (3) ◽  
pp. 1781-1799
Author(s):  
Luca Marino ◽  
Alice Cicirello
Keyword(s):  
Experimental Investigation ◽  
Degree Of Freedom ◽  
Experimental Results ◽  
Systematic Observation ◽  
Stick Slip ◽  
Friction Forces ◽  
Single Degree Of Freedom ◽  
Sdof System ◽  
Single Degree ◽  
Set Up

AbstractThis paper presents an experimental investigation of the dynamic behaviour of a single-degree-of-freedom (SDoF) system with a metal-to-metal contact under harmonic base or joined base-wall excitation. The experimental results are compared with those yielded by mathematical models based on a SDoF system with Coulomb damping. While previous experiments on friction-damped systems focused on the characterisation of the friction force, the proposed approach investigates the steady response of a SDoF system when different exciting frequencies and friction forces are applied. The experimental set-up consists of a single-storey building, where harmonic excitation is imposed on a base plate and a friction contact is achieved between a steel top plate and a brass disc. The experimental results are expressed in terms of displacement transmissibility, phase angle and top plate motion in the time and frequency domains. Both continuous and stick-slip motions are investigated. The main results achieved in this paper are: (1) the development of an experimental set-up capable of reproducing friction damping effects on a harmonically excited SDoF system; (2) the validation of the analytical model introduced by Marino et al. (Nonlinear Dyn, 2019. https://doi.org/10.1007/s11071-019-04983-x) and, particularly, the inversion of the transmissibility curves in the joined base-wall motion case; (3) the systematic observation of stick-slip phenomena and their validation with numerical results.

Analysis of Tapered Roller Bearings Considering High Speed and Combined Loading

1976 ◽  
Vol 98 (4) ◽  
pp. 564-572 ◽  
Author(s):  
J. Y. Liu
Keyword(s):  
High Speed ◽  
Analytical Study ◽  
Roller Bearing ◽  
Combined Loading ◽  
Sliding Velocity ◽  
Friction Forces ◽  
Tapered Roller Bearing ◽  
Rolling Contacts ◽  
Tapered Roller ◽  
Tapered Roller Bearings

This paper presents an analytical study of the load distribution in a tapered roller bearing operating at a high speed and under combined loading. The friction forces at the rolling contacts and the cage forces are not considered. A numerical example showing, among other things, the effects of misalignment and speed on the bearing fatigue life and the sliding velocity at the flange contact is given.

Adhesive Effects on Dynamic Friction for Unlubricated Rough Planar Surfaces

2004 ◽  
Author(s):  
Xi Shi ◽  
Andreas A. Polycarpou
Keyword(s):  
Friction Coefficient ◽  
Mean Value ◽  
Friction Model ◽  
Major Influence ◽  
Dynamic Friction ◽  
Friction Behavior ◽  
Friction Forces ◽  
Normal Contact ◽  
Continuous Contact ◽  
Dynamic Friction Coefficient

As the size of contacting and sliding tribosystems decrease, intermolecular or adhesive forces become significant partly due to nanometer size surface roughness. The presence of adhesion has a major influence on the interfacial contact and friction forces as well as the microtribosystem dynamics and thus influences the overall dynamic friction behavior. In this paper, a dynamic friction model that explicitly includes adhesion, interfacial damping and the system dynamics for realistic rough surfaces was developed. The results show that the amplitude and mean value of the time varying normal contact and friction forces increase in the presence of adhesion under continuous contact conditions. Also, due to the attractive nature of adhesion, its presence delays or eliminates the occurrence of loss of contact. Furthermore, in the presence of significant adhesion, dynamic friction behavior is significantly more complicated compared to the no adhesion case, and the dynamic friction coefficient predictions may be misleading. Thus, it is more appropriate to discuss dynamic friction force instead of dynamic friction coefficient under dynamic conditions.

Circular AFM Mode: A New AFM Mode for Investigating Surface Properties

2011 ◽  
Vol 1318 ◽  
Author(s):  
Olivier Noel ◽  
Pierre-Emmanuel Mazeran ◽  
Hussein Nasrallah
Keyword(s):  
Surface Properties ◽  
Stationary State ◽  
High Speed ◽  
Operating Mode ◽  
Relative Displacement ◽  
Sliding Velocity ◽  
Friction Forces ◽  
First Time ◽  
Mode A ◽  
Adhesive Forces

ABSTRACTFor the first time, a new AFM mode is presented that simultaneously allows the measuring of adhesion and friction forces at different constant and continuous sliding velocities. Our methodology consists of implementing a circular relative displacement of the contact to reach a constant sliding velocity, with no stop periods. Some of the main advantages of performing a circular displacement is that continuous and high sliding velocities (more than 1 mm/s) can be reached compared to the low sliding velocities (up to 10 μm/s) available when using commercial AFM. Also, a stationary state is reached when doing measurements. Moreover, the circular mode can be coupled with the classical operating mode, for instance, force spectrum. Main applications of this circular mode are related to metrological measurements in physics that require high speed displacements. As an example, we report the evolution of friction and adhesive forces measured in air at different high sliding velocities.

Atomistics of Friction

2005 ◽  
Author(s):  
Motohisa Hirano
Keyword(s):  
Friction Force ◽  
Translational Motion ◽  
Static Friction ◽  
System Size ◽  
Dynamic Friction ◽  
Friction Forces ◽  
Internal Motions ◽  
Locking Mechanism ◽  
Roughness Model ◽  
Solid Bodies

The atomistic mechanisms are proposed for the origin of the static and the dynamic friction forces. The mechanism for the origin of the static friction force resembles the mechanical locking mechanism in a surface roughness model. The origin of the dynamic friction force is formulated as a problem of how the given translational kinetic energy dissipates into the internal relative motions of constituent atoms of bodies during sliding. From studying that the available phase space volume of the translational motion becomes negligible small for a large system size, compared with that of the internal motions, it is concluded that the energy dissipation occurs irreversibly from the translational motion to the internal motions. A phenomenon of superlubricity, where two solid bodies move relatively with no resistance, is discussed.

Sign in / Sign up

Export Citation Format

Share Document